Mark the memory node with u-boot,dm-spl so we can use it
from early SPL on both R5 and A53.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The spl_enable_dcache() function calls dram_init_banksize()
to get the total memory size. Normally the dram_init_banksize()
setups the memory banks, while the total size is reported
by ddr_init(). This worked so far for K3 since we set the
gd->ram_size in dram_init_banksize() as well.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
implement overrides for spl_spi_boot_bus() and spl_spi_boot_cs()
lookup functions according to bootmode selection, so as to support
both QSPI and OSPI boot using the same build.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
This converts the following to Kconfig:
CONFIG_KIRKWOOD_EGIGA_INIT
CONFIG_KIRKWOOD_PCIE_INIT
CONFIG_KIRKWOOD_RGMII_PAD_1V8
CONFIG_KM_DISABLE_PCIE
Signed-off-by: Tom Rini <trini@konsulko.com>
As things stand currently, there is only one PowerPC platform that
enables the options for CHAIN_OF_TRUST. From the board header files,
remove a number of never-set options. Remove board specific values from
arch/powerpc/include/asm/fsl_secure_boot.h as well. Rework
include/config_fsl_chain_trust.h to not abuse the CONFIG namespace for
constructing CHAIN_BOOT_CMD. Migrate all of the configurable addresses
to Kconfig.
If any platforms are re-introduced with secure boot support, everything
required should still be here, but now in Kconfig, or requires migration
of an option to Kconfig.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The way that secure boot is implemented today on NXP ARM platforms does
not reuse the elements found in include/config_fsl_chain_trust.h to
construct CONFIG_SECBOOT but instead board header files have their
environment setup as needed and then fsl_setenv_chain_of_trust() will
set secureboot in the environment. Remove a large number of unused
defines here.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move setting of SPL_UBOOT_KEY_HASH to a non-NULL value to Kconfig. As
part of this, change fsl_secboot_validate(...) to check that it is
passed a non-empty string, rather than non-NULL.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Make all of the CHAIN_OF_TRUST options be under a single menu and add a
comment for the rest, so the resulting config file reads more clearly.
Remove duplicate CHAIN_OF_TRUST options from
board/congatec/common/Kconfig. Remove duplicate NXP_ESBC config
questions and move to arch/Kconfig.nxp.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_KEY_REVOCATION
CONFIG_SYS_FSL_SFP_BE
CONFIG_SYS_FSL_SFP_LE
CONFIG_SYS_FSL_SFP_VER_3_0
CONFIG_SYS_FSL_SFP_VER_3_2
CONFIG_SYS_FSL_SFP_VER_3_4
CONFIG_SYS_FSL_SRK_LE
This partly means making sure to enable SYS_FSL_ERRATUM_A007186 only for
when CHAIN_OF_TRUST is enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_SEC_MON
CONFIG_SYS_FSL_SEC_MON_BE
CONFIG_SYS_FSL_SEC_MON_LE
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that board/freescale/common/Kconfig is safe to be included once,
globally, rename this to arch/Kconfig.nxp to better reflect that it
contains options that are valid on multiple architectures and SoC
families, and not specific to NXP reference platforms either.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The way that we use this file currently means that we have to guard it
in every platform Kconfig. But it is also required in all NXP
platforms, including non-reference platforms. Make all options in it
have appropriate dependencies so that we can include it a single time
under arch/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_HETROGENOUS_CLUSTERS
CONFIG_SYS_MAPLE
CONFIG_SYS_CPRI
CONFIG_PPC_CLUSTER_START
CONFIG_DSP_CLUSTER_START
CONFIG_SYS_CPRI_CLK
CONFIG_SYS_ULB_CLK
CONFIG_SYS_ETVPE_CLK
Signed-off-by: Tom Rini <trini@konsulko.com>
We rename the S5P specific "CONFIG_PWM" to CONFIG_PWM_S5P and move it to
Kconfig. Given the usage of CONFIG_PWM_NX, we have that select this new
symbol.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
After more patches code for jumping to _start_cont symbol in flash memory
involved to code with useless mathematical operations. Currently it does:
r3 := CONFIG_SYS_MONITOR_BASE + ABS(_start_cont) - CONFIG_SYS_MONITOR_BASE
jump to r3
Which is equivalent of just:
r3 := ABS(_start_cont)
jump to r3
The purpose of that code is just to jump to _start_code symbol,
independently of program counter. So branch must be done to absolute
address. Trying to write:
ba _start_cont
just cause linker error:
LD u-boot
powerpc-linux-gnuspe-ld.bfd: arch/powerpc/cpu/mpc85xx/start.o: in function `switch_as':
(.bootpg+0x4b8): relocation truncated to fit: R_PPC_ADDR24 against symbol `_start_cont' defined in .text section in arch/powerpc/cpu/mpc85xx/start.o
make: *** [Makefile:1801: u-boot] Error 1
Probably by the fact that absolute address cannot be expressed by 24-bits.
So write the code via mtlr+blr pattern as it was before and load general
purpose register with absolute address of the symbol:
lis r3,_start_cont@h
ori r3,r3,_start_cont@l
mtlr r3
blr
Seems that gcc and gnu ld linker support symbol@h and symbol@l syntax like
number@h and number@l without any problem. And disassembling of compiler
u-boot binary proved that lis+ori instructions are called with numbers
which represent halves of absolute address of _start_cont symbol.
Signed-off-by: Pali Rohár <pali@kernel.org>
DT node pic@40000 is defined explicitly in p2020-post.dtsi file and also
transitionally via include file pq3-mpic.dtsi. Remove duplicate definition
from p2020-post.dtsi.
No change in final DTB file.
Signed-off-by: Pali Rohár <pali@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmK9nEUcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyEu0B/4v1EQOMBL+VXns8Ipo
Xeq+RDUX/24XcB5s6sTcNlWzvYuX6Z7DCGJ0loK5JxelrOy+YNkRbTRMom1eW9Kn
9dmKa0bcO7auJEww3Nln1IFyx+FXQFGR1V3g1U4535l8b7urTioIK0MUSrG/GLpe
Rlbh31GAYtrGvl06W1F7mwhg7/0AT8IhUFaY9G7s7gKA5muGQQ7ED4nKVoZPeTAl
lrQ/Ecym1ND7aOhd/vuEBtgoGxDWzwf8piT8qykJluJKzBV1Hic0RXCNBmtrTORz
b1GOOpRUgcnTv9U8j4PRyYGKDnmS2OmV2AwL8+V9UJfJgQrkcRlbgpCysIPmMBzo
YPRt
=D79P
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.10 cycle:
This feature set includes mostly fixes and alignments: DT alignment with
Linux for sama7g5, removal of invalid eeprom compatibles, removal of
extra debug_uart_init calls for all at91 boards, support for pio4 driver
pioE bank, and other minor fixes and enhancements for sam9x60 and
sama5d2_icp boards.
On versal platform, enable apb linear mode for apb read and write
execute operations amd disable it when using dma reads. This is done by
xilinx_pm_request() secure calls when CONFIG_ZYNQMP_FIRMWARE is enabled,
else we use direct raw reads and writes in case of mini U-Boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-5-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When flash operated at non default mode like DDR, flash need to be reset
to operate in SDR mode to read flash ids by spi-nor framework. Reset the
flash to the default state before using the flash. This reset is handled
by a gpio driver, in case of mini U-Boot as gpio driver is disabled, we
do raw read and write access by the registers.
Versal platform utilizes spi calibration for read delay programming, so
incase by default read delay property is set in DT. We make sure not to
use read delay from DT by overwriting read_delay with -1.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Introduce board/siemens/common/Kconfig and have it hold FACTORYSET to
start with. Use select for this on the boards that need it.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
of U-Boot usage.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since bb5930d5c9 ("exynos: video: Convert several boards to driver
model for video") there have been no callers of any of the exynos_lcd_*
family of functions. Remove these from the boards, and then remove
unused logo and related code as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
The only use of CONFIG_XTFPGA was to build all of the in-tree device
trees. Switch to using CONFIG_XTENSA instead of a non-Kconfig symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a TPL
specific option has at least a direct dependency on TPL. In places
where it's clear that we depend on something more specific, use that
dependency instead.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We want to keep all of the default values for SPL_LDSCRIPT in the same
place both for overall clarity as well as not polluting unrelated config
files.
Signed-off-by: Tom Rini <trini@konsulko.com>
The commit 99e2fbcb69 ("linker_lists: Rename sections to remove .
prefix") changed the name of the linker list sections. As the Aspeed SPL
linker wasn't in the tree yet, it missed the change.
This updates the SPL linker to match arch/arm/cpu/u-boot-spl.lds which
Aspeed was copied from.
Fixes: 442a69c143 ("configs: ast2600: Move SPL bss section to DRAM space")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Currently CONFIG_SPL_TEXT_BASE and CONFIG_SYS_TEXT_BASE addresses are
manually increased by 0x1000 due to .bootpg section. This section has size
of 0x1000 bytes and is manually put by linker script before .text section
(and therefore before base address) when CONFIG_SYS_MPC85XX_NO_RESETVEC is
set. Due to this fact lot of other config options are manually increased by
0x1000 value to make correct layout. Note that entry point is not on
CONFIG_SPL_TEXT_BASE (image+0x1000) but it is really on address
CONFIG_SPL_TEXT_BASE-0x1000 (means at the start of the image).
Cleanup handling of .bootpg section when CONFIG_SYS_MPC85XX_NO_RESETVEC is
set. Put .bootpg code directly into .text section and move text base
address to the start of .bootpg code. And finally remove +0x1000 value from
lot of config options. With this removal custom PHDRS is not used anymore,
so remove it too.
After this change entry point would be at CONFIG_SPL_TEXT_BASE and not at
address -0x1000 anymore.
Tested on P2020 board with SPL and proper U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
The memory on this board is microchip 24aa025e48 which is compatible with
at24c02 with a page size of 16.
Fix the compatible accordingly.
Reported-by: Sergiu Moga <sergiu.moga@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
microchip,24aa025e48 does not exist in the bindings of this driver.
It can be replaced with atmel,at24c02 which is a standard compatible
and the memory is compatible with this one, depending on the page size.
microchip 24aa02e48 has a page size of 8, while 24aa025e48 has a page
size of 16 bytes.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
Change the compatible of the qspi child node to
`jedec,spi-nor` so that it can be properly found
when probing the bus.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
