2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-24 03:53:31 +00:00
Commit graph

46 commits

Author SHA1 Message Date
Francesco Dolcini
a591e75fbc apalis-imx6: use dynamic DDR calibration
Enable dynamic DDR calibration to have a reliable behavior on edge
temperatures conditions.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2021-10-19 10:51:39 +02:00
Tom Rini
9774462e34 arm: Disable ATAGs support
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support.  A large number of platforms had enabled
support but never supported a kernel so old as to require it.  Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years.  This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user.  When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts.  In other cases, these
functions were simply unused, so drop them.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-07 16:22:30 -04:00
Harald Seiler
35b65dd8ef reset: Remove addr parameter from reset_cpu()
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to.  This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value.  Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.

Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g.  COLD vs WARM resets).  As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).

To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely.  Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.

This transformation was done with the following coccinelle patch:

    @@
    expression argvalue;
    @@
    - reset_cpu(argvalue)
    + reset_cpu()

    @@
    identifier argname;
    type argtype;
    @@
    - reset_cpu(argtype argname)
    + reset_cpu(void)
    { ... }

Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-03-02 14:03:02 -05:00
Simon Glass
401d1c4f5d common: Drop asm/global_data.h from common header
Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-02 15:33:42 -05:00
Simon Glass
20e442ab2d dm: Rename U_BOOT_DEVICE() to U_BOOT_DRVINFO()
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.

The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)

It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.

Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:26:35 -07:00
Simon Glass
8a8d24bdf1 dm: treewide: Rename ..._platdata variables to just ..._plat
Try to maintain some consistency between these variables by using _plat as
a suffix for them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 16:51:09 -07:00
Simon Glass
caa4daa2ae dm: treewide: Rename 'platdata' variables to just 'plat'
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).

Rename some of the latter variables to end with 'plat' for consistency.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 16:51:08 -07:00
Masahiro Yamada
b75d8dc564 treewide: convert bd_t to struct bd_info by coccinelle
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:

  It's a **mistake** to use typedef for structures and pointers.

Besides, using typedef for structures is annoying when you try to make
headers self-contained.

Let's say you have the following function declaration in a header:

  void foo(bd_t *bd);

This is not self-contained since bd_t is not defined.

To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>

  #include <asm/u-boot.h>
  void foo(bd_t *bd);

Then, the include direcective pulls in more bloat needlessly.

If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:

  struct bd_info;
  void foo(struct bd_info *bd);

Right, typedef'ing bd_t is a mistake.

I used coccinelle to generate this commit.

The semantic patch that makes this change is as follows:

  <smpl>
  @@
  typedef bd_t;
  @@
  -bd_t
  +struct bd_info
  </smpl>

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-07-17 09:30:13 -04:00
Simon Glass
cd93d625fd common: Drop linux/bitops.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
c05ed00afb common: Drop linux/delay.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
4d72caa5b9 common: Drop image.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:33 -04:00
Simon Glass
90526e9fba common: Drop net.h from common header
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.

Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:31 -04:00
Philippe Schenker
f72e48ba4d board: apalis_imx6: Add KSZ9131 phy skew settings
This patch adds skew register settings for KSZ9131. It checks first
which phy is on the board and then applies the correct skew settings.

Skew settings calculation for the KSZ9131:
The i.MX6 SoC has an output skew tolerance of -100ps to 900ps. All
PCB traces where routed exactly the same length so we can calculate
the skew settings without taking the length into consideration. The
traces are all length matched.

RXC skew (PHY to MAC):
- We use the 2ns DLL controlled delay on the PHY
- We do not use the skew registers

This results in the following values:

		RXC
PHY fixed Delay	2000ps
PHY Added Delay	0ps
T_setup_R min	2.00ns
T_setup_R typ	2.00ns
T_setup_R max	2.00ns
T_hold_R min	1.60ns
T_hold_R typ	2.00ns
T_hold_R max	2.40ns

That means we are well within RGMII specs.

TXC skew (MAC to PHY):
- We use the 2ns DLL controlled delay on the PHY
- We then subtract ~0.6ns with TXD[0:3] and TXC clock pad skew
  register in a resulting ~1.4ns delay.

This results in the following values under consideration of the
tolerances:

		TXC min	TXC typ	TXC max
MAC min		-100ps	-100ps	-100ps
MAC max		900ps	900ps	900ps
PHY fixed Delay	2000ps	2000ps	2000ps
PHY added Delay	-340ps	-600ps	-859ps
T_setup_T min	1.56ns	1.30ns	1.04ns
T_setup_T typ	2.06ns	1.80ns	1.54ns
T_setup_T max	2.56ns	2.30ns	2.04ns
T_hold_T min	1.04ns	1.30ns	1.56ns
T_hold_T typ	1.94ns	2.20ns	2.46ns
T_hold_T max	2.84ns	3.10ns	3.36ns

This shows that T_hold_T min and T_setup_T min times are out of spec
for RGMII timing. However the KSZ9131 has a minimal value for this time
of 0.8ns which is met under all circumstances.

Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2020-05-01 13:46:22 +02:00
Simon Glass
9a3b4ceb37 common: Move reset_cpu() to the CPU header
Move this function out of common.h and into a relevant header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-01-17 14:02:31 -05:00
Igor Opaniuk
a781ed271e apalis_imx6: migrate to DM_ETH
Migrate to DM_ETH and remove hardcoded pinmux configuration.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07 10:26:56 +01:00
Simon Glass
5255932f01 common: Move some board functions out of common.h
A number of board function belong in init.h with the others. Move them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:21 -05:00
Ricardo Salveti
536c564b91 apalis_imx6: fix broken fsl_esdhc_imx conversion
Commit e37ac717d7 ("Convert to use fsl_esdhc_imx for i.MX platforms")
converted FSL_ESDHC to FSL_ESDHC_IMX, but the config check for
apalis_imx6 wasn't updated accordantly.

Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2019-10-08 16:35:16 +02:00
Ricardo Salveti
6f8ef051c5 apalis_imx6: add board_fit_config_name_match to support FIT in SPL
Only one dtb is currently supported, so match with imx6-apalis.

Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2019-10-08 16:35:16 +02:00
Simon Glass
e7dcf5645f env: Drop environment.h header file where not needed
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Simon Glass
9fb625ce05 env: Move env_set() to env.h
Move env_set() over to the new header file.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Yangbo Lu
e37ac717d7 Convert to use fsl_esdhc_imx for i.MX platforms
Converted to use fsl_esdhc_imx for i.MX platforms.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
2019-06-23 14:18:34 +08:00
Marek Vasut
64c751f635 ARM: imx: apalis_imx6: Drop ad-hoc SATA binding
Drop the ad-hoc AHCI binding code, this is superseded by
CONFIG_DWC_AHSATA_AHCI=y resp. drivers/ata/dwc_ahsata.c

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-06-11 10:42:48 +02:00
Stefan Agner
15834c6383 apalis_imx6: use SDP if USB serial downloader has been used
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Max Krummenacher
389f61ef44 apalis_imx6: disable ri and dcd irq in uarts
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.

Disable the bits also on UARTs not used in the boot loader to prevent
an interrupt storm when Linux enables the UART interrupts.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Max Krummenacher
3ef55a7473 apalis_imx6: unify sd/mmc drive strength with linux kernel settings
In the Linux device tree we use 40Ohm drive strength. So use the same
value in U-Boot.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
16959d75dd apalis_imx6: drop CONFIG_OF_SYSTEM_SETUP
This doesn't do anything anymore, probably never did.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
9fb4b8929a apalis_imx6: migrate usb to using driver model
Migrate USB to using driver model.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
72b49e2c1e apalis_imx6: migrate mmc and sata to using driver model
Migrate MMC and SATA to using driver model.

While at it also enable SCSI driver model.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
ab92352d22 apalis_imx6: migrate i2c to using driver model
Migrate I2C to using driver model.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
5177087f64 apalis_imx6: clean-up and migrate gpios to using driver model
Migrate GPIOs to using driver model, properly request backlight,
Ethernet PHY reset, MMC/SD card detect and USB power GPIOs and also
enable SION bit in pin muxing for Apalis, backlight, eMMC reset,
Ethernet PHY reset and USB power enable GPIOs.

While at it also update copyright year, clean-up/re-order includes,
add some comments clarifying ifdef scope and do some White-space
clean-up.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Gerard Salvatella
a3c9021771 board: toradex: turn off lcd backlight before OS handover
U-Boot typically tears down the display controller before handing
control over to Linux. On LCD displays disabling pixel clock leads to a
fading out effect with vertical/horizontal lines. Make sure to disable
back light before booting Linux.

Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-02-20 09:01:45 -07:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Masahiro Yamada
b08c8c4870 libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.

This commit moves the header code:
  include/libfdt.h         -> include/linux/libfdt.h
  include/libfdt_env.h     -> include/linux/libfdt_env.h

and replaces include directives:
  #include <libfdt.h>      -> #include <linux/libfdt.h>
  #include <libfdt_env.h>  -> #include <linux/libfdt_env.h>

Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-05 10:16:28 -05:00
Diego Dorta
7594c51ae6 imx: Include <input.h> header file
When building with W=1 errors like the one below is seen:

board/freescale/mx6sabresd/mx6sabresd.c:546:5: warning:
no previous prototype for ‘overwrite_console’
[-Wmissing-prototypes] int overwrite_console(void)

Fix the build warnings by including <input.h>.

Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-12 17:31:16 +02:00
Fabio Estevam
f89bfe7c17 apalis_imx6: Avoid calling setup_display() from SPL code
There is no need call setup_display() from SPL code, so move it to
board_init(), which executes only in U-Boot proper.

Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-10-12 17:30:32 +02:00
Fabio Estevam
511db3bf5a toradex: imx6: Move g_dnl_bind_fixup() into common SPL code
Instead of having every board file to add its own g_dnl_bind_fixup()
implementation, move it to the common imx6 SPL code.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
2017-09-20 15:34:59 +02:00
Breno Lima
3aa4b703b4 imx: imx6: Move gpr_init() function to soc.c
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D,
MX6Q and MX6QP processors move it to the soc.c file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-08-28 09:48:53 +02:00
Stefan Agner
2b2f678280 apalis/colibri_imx6: use independent USB PID for SPL
Use a completely independent USB Product ID for SPL. This allows
to differentiate a SDP running in SPL and SDP running in a U-Boot
which could not read the config block successfully.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
2017-08-23 10:41:58 +02:00
Simon Glass
00caae6d47 env: Rename getenv/_f() to env_get()
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.

Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:30:24 -04:00
Simon Glass
382bee57f1 env: Rename setenv() to env_set()
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:22:18 -04:00
Simon Glass
01510091de env: Drop saveenv() in favour of env_save()
Use the env_save() function directly now that there is only one
implementation of saveenv().

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-08-15 20:50:30 -04:00
Stefano Babic
552a848e4f imx: reorganize IMX code as other SOCs
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.

This change is also coherent with the structure in kernel.

Signed-off-by: Stefano Babic <sbabic@denx.de>

CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-07-12 10:17:44 +02:00
Simon Glass
10e40d54b3 Kconfig: Add CONFIG_SATA to enable SATA
At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-11 10:08:19 -06:00
Simon Glass
9d922450aa dm: Use dm.h header when driver mode is used
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 06:57:52 -06:00
Tom Rini
cb72931553 apalis_imx6: Fix unused variable warning
The variable vga_pads is never referenced, drop.

Cc: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2017-05-12 08:37:28 -04:00
Max Krummenacher
592f4aed6d arm: imx: initial support for apalis imx6
This adds board support for the Toradex module family Apalis iMX6.
The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with
commercial and industrial temperature range.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-12-16 10:02:45 +01:00