This is long over due. All but two net drivers have been converted, but
those have now been dropped.
The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined. So here we scrub the
core code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This pushes the ugly duplicated arch ifdef lists we maintain in various
image related files out to the arch headers themselves.
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current post_log_word in global data is currently split into 2x
16 bits: half for the test start, half for the test success.
Since we alredy have more than 16 POST tests defined and more could
be defined, this may result in an overflow and the post_output_backlog
would not work for the tests defined further of these 16 positions.
An additional field is added to global data so that we can now support up
to 32 (depending of architecture) tests. The post_log_word is only used
to record the start of the test and the new field post_log_res for the
test success (or failure). The post_output_backlog is for this change
also adapted.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Allow redirection of console output prior to console initialisation to a
temporary buffer.
To enable this functionality, the board (or arch) must define:
- CONFIG_PRE_CONSOLE_BUFFER - Enable pre-console buffer
- CONFIG_PRE_CON_BUF_ADDR - Base address of pre-console buffer
- CONFIG_PRE_CON_BUF_SZ - Size of pre-console buffer (in bytes)
The pre-console buffer will buffer the last CONFIG_PRE_CON_BUF_SZ bytes
Any earlier characters are silently dropped.
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
Add P3060 SoC specific information:cores setup, LIODN setup, etc
The P3060 SoC combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for Job Queue/Ring LIODN for the RAID Engine on P5020. Each
Job Queue/Ring combo needs one id assigned for a total of 4 (2 JQs/2
Rings per JQ). This just handles RAID Engine in non-DPAA mode.
Signed-off-by: Santosh Shukla <santosh.shukla@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].
Refer to the erratum LBIU3 of mpc8548.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some
early version silicons. The default settings of the DDR IO receiver
biasing may not work at cold temperature. When a failure occurs,
a DDR input latches an incorrect value. The workaround will set the
receiver to an acceptable bias point.
Signed-off-by: Gong Chen
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Pre u-boot Flow:
1. User loads the u-boot image in flash
2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000
(Please note that ISBC expects all these addresses, images to be
validated, entry point etc within 0 - 3.5G range)
3. ISBC validates the u-boot image, and passes control to u-boot
at 0xcffffffc.
Changes in u-boot:
1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M
CONFIG_SYS_PBI_FLASH_WINDOW in AS=1.
(The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash
created by PBL/configuration word within 0 - 3.5G memory range. The
u-boot image at this address has been validated by ISBC code)
2. Remove TLB entries for 0 - 3.5G created by ISBC code
3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by
PBL/configuration word after switch to AS = 1
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com>
Acked-by: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The EST SBC8260 is over 10 years old, and the SBC8240 older than
that. With the tiny amount of RAM (by today's standards), there
really isn't anyone interested in running the latest U-boot on
these EOL products anymore.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: jon.diekema@smiths-aerospace.com
There are some locations in the code which anticipate printf() being called
before the console is ready by squelching printf() on gd->have_console.
Move this squelching into printf(), vprintf(), puts() and putc(). Also
make tstc() and getc() return 0 if console is not yet initialised
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
Unified DDR driver is maintained for better performance, robustness and bug
fixes. Upgrading to use unified DDR driver for MPC83xx takes advantage of
overall improvement. It requires changes for board files to customize
platform-dependent parameters.
To utilize the unified DDR driver, a board needs to define CONFIG_FSL_DDRx
in the header file. No more boards will be accepted without such definition.
Note: the workaround for erratum DDR6 for the very old MPC834x Rev 1.0/1.1
and MPC8360 Rev 1.1/1.2 parts is not migrated to unified driver.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DDR2 has different ODT table and values. Adding table according to Samsung
application note.
Fix additive latency calculation to avoid interger underflow.
Also converted typedef dynamic_odt_t to struct dynamic_odt.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The two slots on the same controller have different addresses.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Check second DIMM slot in case the first one is empty.
Honor DQS enable option for SDRAM mode register.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DDR RCW varies at different speeds. It is common for all platform. Move it
out from corenet_ds.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Extend CAS write Latency (CWL) table to comply with DDR3 spec
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8536 seems to use only 3 bits for the major revision field in the
SVR rather than the 4 bits used by all other processors. The most
significant bit is used as a mfg code on MPC8536.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 has two 1G ethernet controllers the first can run in
SGMII, RGMII, or RMII. The second can only do SGMII & RGMII.
We need to setup a for SoC & board registers based on our various
configuration for ethernet to function properly on the board.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block. Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman). However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.
Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely. This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.
Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.
We add support for the following SoCs:
* P1023 - 1 Fman, 2x1g
* P4080 - 2 Fman, each Fman has 4x1g and 1x10g
* P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some SOCs have discontiguously-numbered cores, and so we can't determine the
valid core numbers via the FRR register any more. We define
CPU_TYPE_ENTRY_MASK to specify a discontiguous core mask, and helper functions
to process the mask and enumerate over the set of valid cores.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The old fdt_create_phandle didn't actually create a phandle it just
set one. We'll introduce a new helper that actually does creation.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Add ifdef protection around fman specific code related to device tree
clock setup. If we dont have CONFIG_SYS_DPAA_FMAN defined we shouldn't
be executing this code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Issue: Address masking doesn't work properly.
When sum of the base address, defined by BA, and memory bank size,
defined by AM, exceeds 4GB (0xffff_ffff) then AMASKn[AM] doesn't mask
CSPRn[BA] bits.
Impact:
This will impact booting when we are reprogramming CSPR0(BA) and
AMASK0(AMASK) while executing from NOR Flash.
Workaround:
Re-programming of CSPR(BA) and AMASK is done while not executing from NOR
Flash. The code which programs the BA and AMASK is executed from L2-SRAM.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Issue:
Peripheral connected to IFC_CS3 may hamper booting from IFC.
Impact:
Boot from IFC may not be successful if IFC_CS3 is used.
Workaround:
If IFC_CS3 is used, gate IFC_CS3 while booting from NAND or NOR.
Also Software should select IFC_CS3 using PMUXCR[26:27] = 0x01.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Issue:
The NOR-FCM does not support access to unaligned addresses for 16 bit port size
Impact:
When 16 bit port size is used, accesses not aligned to 16 bit address boundary
will result in incorrect data
Workaround:
The workaround is to switch to GPCM mode for NOR Flash access.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For an IFC Erratum (A-003399) we will need to access IFC registers in
cpu_init_early_f() so expand the TLB covering CCSR to 1M.
Since we need a TLB to cover 1M we move to using TLB1 array for all the
early mappings so we can cover various sizes beyond 4k.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add NAND support (including spl) on IFC, such as is found on the p1010.
Note that using hardware ECC on IFC with small-page NAND (which is what
comes on the p1010rdb reference board) means there will be insufficient
OOB space for JFFS2, since IFC does not support 1-bit ECC. UBI should
work, as it does not use OOB for anything but ECC.
When hardware ECC is not enabled in CSOR, software ECC is now used.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
[scottwood@freescale.com: ECC rework and misc fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Before main memory (DDR) is initialized, the on-chip L1 cache is used as a
memory area for the stack and the global data (gd_t) structure. This is
called the initial RAM area, or initram. The L1 cache is locked and the TLBs
point to a non-existent address (so that there's no chance it will overlap
main memory or any device). The L1 cache is also configured not to write
out to memory or the L2 cache, so everything stays in the L1 cache.
One of the things we might do while running out of initram is relocate CCSR.
On reset, CCSR is typically located at some high 32-bit address, like
0xfe000000, and this may not be the best place for CCSR. For example, on
36-bit systems, CCSR is relocated to 0xffe000000, near the top of 36-bit
memory space.
On some future Freescale SOCs, the L1 cache will be forced to write to the
backing store, so we can no longer have the TLBs point to non-existent address.
Instead, we will point the TLBs to an unused area in CCSR. In order for this
technique to work, CCSR needs to be relocated before the initram memory is
enabled.
Unlike the original CCSR relocation code in cpu_init_early_f(), the TLBs
we create now for relocating CCSR are deleted after the relocation is finished.
cpu_init_early_f() will still need to create a TLB for CCSR (at the new
location) for normal U-Boot purposes. This is done to keep the impact to
existing U-Boot code minimal and to better isolate the CCSR relocation code.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.
CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file. Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.
CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.
Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot). All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.
README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
- Use both getenv() and hwconfig to get USB phy type till getenv()
is depricated
- Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
has internal UTMI phy
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Flush the dcache before removing the TLB with caches enabled.
Otherwise this might lead to problems later on, e.g. while booting
Linux (as seen on ICON-440SPe).
Signed-off-by: Stefan Roese <sr@denx.de>
Change bd_t->bi_phy* arrays from 1 to 2 for PPC405EX since
405EX has 2 ethernet interfaces.
Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Since we are loading an executable image into memory we need flush it
out of the cache to possible maintain coherence on CPUs with split
instruction and data caches. We do this for other executable image
loading command.
On PowerPC once we do this we no longer need to explicitly flush the
dcache on multi-core systems in the BOOTM_STATE_OS_PREP phase. We now
treat the BOOTM_STATE_OS_PREP as a no-op to maintain backwards
compatibility with the bootm subcommand.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Diana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
The U-Boot Design Principles[1] clearly say:
Initialize devices only when they are needed within U-Boot, i.e. don't
initialize the Ethernet interface(s) unless U-Boot performs a download
over Ethernet; don't initialize any IDE or USB devices unless U-Boot
actually tries to load files from these, etc. (and don't forget to
shut down these devices after using them - otherwise nasty things may
happen when you try to boot your OS).
So, do not initialize and read the sensors on startup.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Holger Brunck <holger.brunck@keymile.com>
The SHARP LQ084S3LG01 is a TFT LCD used on the P1022DS (revision "C") board.
This device only supports 800x600 resolution, so if that resolution is selected,
assume that this is the device. The device is attached to the LVDS port
on the P1022DS board.
The existing 800x600 entry (for the PDM360NG board) is actually 800x480,
so we fix that. To support two different 800x resolutions, the Y-resolution
is now passed to fsl_diu_init() and both values are used to pick the proper
fb_videomode structure.
The data for the 800x600 video mode is originally from Jiang Yutang.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
We used <usb.h> for USB_MAX_DEVICE. However this requires we actual
build in support for USB into u-boot (which should not be required for
device tree fixup).
At this time no FSL SoC that utilizies this code (83xx/85xx) has more
than 2 USB controllers. So we replace USB_MAX_DEVICE with a local
define FSL_MAX_NUM_USB_CTRLS.
If/when a device shows up with more than 2 controllers we can easily
bump this value or refactor into a proper define per SoC.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to
'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break
out if it cannot find 'usb1', so drop the 'else' clause to make driver scan
all the 'usbx'.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce ft_verify_fdt(), a function that is called after the device tree
has been fixed up, that displays warning messages if there is a mismatch
between the physical addresses of some devices that U-Boot has configured
with what the device tree says the addresses are.
This is a particular problem when booting a 36-bit device tree from a
32-bit U-Boot (or vice versa), because the physical address of CCSR is
wrong in the device tree. When the operating system boots, no messages are
displayed, so the user generally has no idea what's wrong.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current code would print RAM size information like this:
DRAM: DDR: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Turn a number of printf()s into debug() to get rid of the redundant
"DDR: " string like this:
DRAM: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
At some point we broke the detection of e500v1 class cores. Fix that
and simply the code to just utilize PVR_VER() to have a single case
statement.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix up the device tree property associated with the Flexcan clock
frequency. This property is used to calculate the bit timing parameters
for Flexcan.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This provides a function that will override the weak function
flush_icache to let 85xx boards to flush the icache
cc: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
The P2040/P2040E have no L2 cache. So we utilize the SVR to determine
if we are one of these devices and skip the L2 init code in cpu_init.c
and release. For the device tree we skip the updating of the L2 cache
properties but we still update the chain of caches so the CPC/L3 node
can be properly updated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We add XAUI_FM1 into the SERDES tables for P2041[e] devices. However
for the P2040[e] devices that dont support XAUI we handle this at
runtime via SVR checks. If we are on a P2040[e] device the SERDES
functions will behave as follows:
is_serdes_prtcl_valid() will always report invalid if prtcl passed in is
XAUI_FM1.
serdes_get_prtcl() will report NONE if the prtcl in the table is set to
XAUI_FM1.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2041 is the superset part that covers both P2040 & P2041. The only
difference between the two devices is that P2041 supports 10g/XAUI and
has an L2 cache.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
