Remove legacy command definitions, change to use new ELE_xxx command
request.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add get_events API to retrieve any singular events that has occurred
since the FW has started from sentinel
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The ECC fuse on 8ULP can't be written twice. If any user did it, the
ECC value would be wrong then cause accessing problem to the fuse.
The patch will lock the ECC fuse word to avoid this problem.
For iMX9, the OTP controller automatically prevents an ECC fuse word to
be written twice. So it does not need the setting.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since new 8ULP A1 S400 FW (v0.0.8-e329b760) can support to read
more fuses: like PMU trim, Test flow/USB, GP1-5, GP8-10. Update
the u-boot driver for the new mapping.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Alice Guo <alice.guo@nxp.com>
To align with ARM trusted firmware's change, adjust DRAM timing
save area to new position 0x20055000. So we can release the space
since 0x2006c000 for the NOBITS region of ARM trusted firmware
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmQirs0cHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyIWBCACz3Bh76v3vbqhaQPBq
ZGB+jnaZQsWW9r285dCmQFA/xGLbQoMVIhzvLVmEcZdr0d9wHUEsy1IzC6tak2MJ
NkiYcNRb3lnYEDthvjGdpz6QIGZBBOj8l8ha70z4ZvzBwTfOReB04N5207n5Tzq/
hAFAWcM3VxfVXF2Xb8O/HbyEbOVXKY65xWinAIZqvGscox+vx3Vj9m1aLqcQP0Wy
bCZowynfyKWiFrHr5TYgpmL4ROsj3jbnRhC0dqyB+ewRdRAK4uVJXRj23ywwDcGH
VqlYFVFT8EY5HSzCG8VGMtGqV+H4+K4RYiTLtDwtbHWdXnUKLKORXtXi2xcHHxS1
rj5U
=kb6/
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.07-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.07 cycle:
This feature set includes the clock changes required for sam9x60 SoC to
support USB host.
In order for some of the functionalities, such as the USB clocks,
to work properly we need some clocks to be properly initialised
at the very beginning of booting.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Clock setup was intended for setting clocks at boot time on SAMA7G5,
e.g. for root clocks like PLLs, that were used to feed IPs needed alive
in u-boot (e.g. Ethernet clock feed by a PLL). Export this functionality
to all at91 clocks as it may be necessary on other SoCs.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Register into DM the clocks required to properly enable USB functionality
within the bootloader.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Implement sam9x60 USB clock driver. This clock has
three parents: PLLA, UPLL and MAINXTAL. The driver is
aware of the three possible parents with the help of the
two mux tables provied to the driver during the registration
of the clock.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
- Fixes for booting newer revs of the SoC in the Raspberry Pi 4
- Propagate some firmware DT properties to the loaded DT
- Update the Zero2W upstream DT name
Newer firmware can manage the SDCDIV clock divisor register, allowing
the divisor to scale with the core as necessary.
Leverage this ability if the firmware supports it.
Adapted from the following raspberrypi Linux kernel commit:
bcm2835-sdhost: Firmware manages the clock divisor
08532d242d
Signed-off-by: Vincent Fazio <vfazio@xes-inc.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Setting RX flow error handling will stall the channel until descriptors
are available to move RX data. Setting this bit causes issues when
tearing down ethernet DMA channel at the end of TFTP transfer as
unrelated network packets can cause teardown to stall indefinitely waiting
for driver to queue add more desc leading to channel hang with error
logs:
udma_stop_dev2mem TIMEOUT !
udma_stop_dev2mem: peer not stopped TIMEOUT !
udma_stop_dev2mem TIMEOUT !
Fix this by clearing rx_error_handling similar to how its done for UDMA
as part of udma_alloc_rchan_sci_req()
This fixes occasional TFTP Failures seen when downloading multiple files
one after the other on AM64/AM62 SoCs.
Fixes: 9a92851c33 ("dma: ti: k3-udma: Add BCDMA and PKTDMA support")
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The reset identifier must be processed via MOD_CLK_PACK() before it is
used to look up register and bit within reset_regs or reset_clear_regs
arrays, otherwise completely bogus register and bit is picked from the
arrays, one which may even be out of range.
Fixes: 326e05c5e2 ("clk: renesas: Add and enable CPG reset driver")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In the binding for the Rockchip timer the compatible string
consists of a SoC orientated string and a fall back string
"rockchip,rk3288-timer", so remove all unneeded ones and
fix driver name.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For Rockchip platform, DLL bypass bit and start bit need to be set if
DLL is not locked.
With this change applied eMMC in my NanoPi R5S can run at 52 MHz.
Based on linux commit b75a52b0dda3 ("mmc: sdhci-of-dwcmshc: Update DLL
and pre-change delay for rockchip platform")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Device tree contains assigned-clock-rates property for these,
but default value will work just fine
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
The get_mmc_clk ops is expected to set a clock rate and return the
configured rate as an unsigned value. However, if clk_set_rate fails,
e.g. using a fixed rate clock, a negative error value is returned.
The mmc core will treat this as a valid unsigned rate and tries to
configure a divider based on this bogus clock rate.
Use 0 as the return value when setting clock rate fails, the mmc core
will configure to use bypass mode instead of using a bogus divider.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rate and error value is not returned for aux16m clocks, fix this.
Fixes: 7a474df740 ("clk: rockchip: Add rk3588 clk support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Make the indent of these macro elements consistent with the
rest of this table. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for debug output very early during boot using the DEBUG_UART
mechanism. This uses a static fixed UART port configuration selected via
Kconfig options and dedicated print functions from debug_uart.h. This is
useful e.g. when debugging problems so early during boot, that not even
the DM is initialized at that point, and thus DM_SERIAL is not available
either.
This functionality is disabled by default. To activate it, define the
following Kconfig options and select SCIF type using CFG_SCI/CFG_SCIF_A/
CFG_HSCIF/<nothing for regular SCIF>:
CONFIG_DEBUG_UART=y
CONFIG_DEBUG_UART_SCIF=y
CONFIG_DEBUG_UART_BASE=0xe6540000
CONFIG_DEBUG_UART_CLOCK=24000000
The later two options define the SCIF physical base address and SCIF
input clock in Hz. Optionally, to validate DEBUG_UART works, enable
the following as well to get early serial output message by default:
CONFIG_DEBUG_UART_ANNOUNCE=y
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Both CONFIG_SCI and CONFIG_SCIF_USE_EXT_CLK options do not have a
matching Kconfig entry because they are internal to the SCIF driver.
Change their prefix to CFG_, i.e. CFG_SCIF_USE_EXT_CLK and CFG_SCI,
to reflect that and avoid interferring with Kconfig symbols. Since
neither of those options are defined elsewhere, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Switch ifdef in sh_gpio_get_value() to IS_ENABLED() macro.
The CONFIG_RCAR_GEN3 will never have SPL counterpart, so
the IS_ENABLED() macro is the right one here. No functional
change, except for improved build test coverage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Calling old U-Boot API doesn't allow to use fixed PHY.
Searching by mask is the part of new function, after
scanning FDT for a fixed PHY definition
Fixes: e821a7bdb1 ("net: ravb: Detect PHY correctly")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Mikhail Lappo <mikhail.lappo@esrlabs.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
[Hai Pham: Drop phy_connect_dev since it's called in phy_connect]
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Use mask -1 instead of 0 to reinstate the search behavior
over all PHY addresses. Add Fixes tag, sort the tag list.]
Sort the list of "depends" symbols in ascending order.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Sort the list of "depends" symbols in ascending order.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Do not cache the single CPG MODE register bit 12, instead cache the
entire register value, and only pick the matching bit from the cached
value when core clock of type MDSEL or PE are used. Both MDSEL and PE
clock type currently define .offset field as 12 on Gen3, which means
this code will use bit 12 on Gen3 again, however there are additional
clock on Gen4 which use different bits, and having this flexibility
in place now will be useful when adding Gen4.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This reverts commit 9f62a472df.
The changes here aren't quite right, and on platforms such as Raspberry
Pi where we can have both serial and video output, the change above
causes output to change. This can be seen as the hush tests we have now
fail.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is better to clear the console device rather than the video device,
since the console has the text display. We also need to reset the cursor
position with the console, but not with the video device.
Add a new function to handle this and update the 'cls' command to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is not possible for the video driver to use a pre-allocated
frame buffer (such as is done with EFI) with the copy framebuffer. This
can be useful to speed up the display.
Adjust the implementation so that copy_size can be set to the required
size, with this being allocated if the normal framebuffer size is 0.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for this to EFI in case it becomes useful. At present it just
slows things down. You can enable CONFIG_VIDEO_COPY to turn it on.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is not yet clear how to read the timer via EFI. The current value seems
much too high on a Framework laptop I tried. Adjust it to a lower
hard-coded value for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current vesa structure only provides a 32-bit value for the frame
buffer. Many modern machines use an address outside the range.
It is still useful to have this common struct, but add a separate
frame-buffer address as well.
Add a comment for vesa_setup_video_priv() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Put this into a function, as we have done for the app implementation.
Comment both functions. FOr now the app still does not access it
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add new sysinfo IDs for R-Car V3H Condor/Condor-I .
Enable support for sysinfo on R-Car V3H Condor/Condor-I. The sysinfo is
used e.g. to access and decode board-specific information and then in
turn used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77980.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Update the commit message, note the new sysinfo IDs.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Correct the board code ID based on the hardware documentation
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Remove PFC info table entries which are never instantiated,
since there are no drivers for those. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The CLK_RCAR_GEN3 registers two subdrivers, clk_gen3 and rst_gen3.
The former depends on the clock framework, which is always enabled
in this context of clock framework driver, while the later depends
on reset framework which may not always be enabled.
Ensure the reset framework is also always enabled to prevent inobvious
early boot time bind failure of the CPG driver, which leads to system
showing no activity and is difficult to debug.
Note that one possible approach to debug this is to use CONFIG_DEBUG_UART
and add debug printascii()s into the drivers/clk/renesas/clk-rcar-gen3.c .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
In case one of the calls in probe fail, trigger a fail path and
undo all the steps done in probe until the point of failure.
The current implementation failed to stop controller clock and
free claimed clock, so fix that. Furthermore, print return code
in error prints for easier debugging.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The prior stage bootloader might have left the SDnCKCR register in completely
arbitrary state before passing control to U-Boot, which includes the register
being populated with incorrect values. Currently the SDHI driver will attempt
to use clock framework to configure SDn clock, which may fail in case SDnCKCR
contains invalid values for the SDnH clock, because the clock framework would
not be able to determine SDnH clock rate and would get -EINVAL instead, which
in turn would not allow the clock framework to determine the correct SDn clock
divider ratio.
This failure occurs specifically in case SDnCKCR reads back 0x209 .
Correct the problem by first setting default SDnH clock rate to 800 MHz, thus
assuring the SDnCKCR SDnH bits are correct, and only afterward set up the SDn
clock rate to default 200 MHz.
Note that the SDHI driver may reconfigure SDnH clock later based on IOS
settings obtained from the attached card, the 800 MHz set up here is only
the default value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
