A "send status" command is added with the commit "mmc: checking
status after commands with R1b response". But the status register
returned from send status command of SPI protocol is different from
that of MMC/SD protocol. We do a simple test and generate a response
in stead of full bit-by-bit translation.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
The otc570 board support was broken. Within this opportunity, I completely
reworked the board files.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
ftahbc020s.h provides basic definitions of this controller
to help a SoC which use this AHB Controller could
do scalable software settings in lowlevel_init.S.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
as checkpatch proposes to use strict_strtoul instead of
simple_strtoul, introduce it.
Ported this function from Linux 2.6.38 commit ID:
521cb40b0c44418a4fd36dc633f575813d59a43d
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This is needed for the upcoming TFTP server implementation.
This also simplifies PingHandler() and fixes rxhand_f documentation.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
APM errata CHIP_21 for the 405EX/EXr (from the rev 1.09 document dated
4/27/11) states that rev D processors may wake up with the wrong feature
set. This patch implements the APM-proposed workaround.
To enable this patch for your board, add the appropriate define for your
CPU to your board header file. See kilauea.h for more information. The
following variants are supported:
#define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY
Please note that if you select the wrong define, your board will not
boot, and JTAG will be required to recover.
Tested on custom boards using:
CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY <sfalco@harris.com>
CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY <eibach@gdsys.de>
Signed-off-by: Steve Falco <sfalco@harris.com>
Acked-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Though the OpenRD-Base only has one gigabit Ethernet port,
both the OpenRD-Client and OpenRD-Ultimate each have two.
On the Ultimate, the PHY addresses are consecutive, but
on the Client they are not.
(based on
<62a0952ce368acc725063a00a5ec680a639d6c27.1301040318.git.julian.pidancet@citrix.com>
<ad0a2dc1e422698b005d6f0ceb6dd6f75a87e00a.1301040318.git.julian.pidancet@citrix.com>
)
Signed-off-by: Clint Adams <clint@debian.org>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Julian Pidancet <julian.pidancet@citrix.com>
The asm/arch/config.h header define CONFIG_NR_DRAM_BANKS_MAX, which is
needed to configure DRAM banks.
This patch move the asm/arch/config.h header inclusion above the DRAM
banks configuration.
Additionally this patch fix a typo.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
The initial_boot_bank can be set when more than one application is
used in a bootpackage. But a value n <> 0 never led to booting from
bank n. Instead, bank 0 was booted. This patch fixes this.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
commit 91a3c14c (ppc, mgcoge: add DIP switch detection)
introduces an compile error due to an missing define in the
mgcoge2ne.h. DIP switch detection is valid for both boards.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Heiko Schocher <hs@denx.de>
On mgcoge3ne a new environment variable bobcatreset is used.
So this patch adds a possibility to add board specific
environment variables in general and this specific variable
for mgcoge3ne.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reserved bit was changed according to the processors manual.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch adds support for the MPC8247 based board mgcoge3ne.
Additionaly mgcoge2ne board supprot was removed, because due
to the mgcoge3ne, this board is obsolete and not longer
maintained.
The board is similar to mgcoge. The difference is that
a NUMONYX flash is used and a different SDRAM (256MB).
Also introduce CONFIG_KM_82XX to collect ppc82xx common
settings and remove staticness from the common set_pin function.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
Introduce a struct for the BFTICU FPGA to increase the readability of
the code. And the define CONFIG_SYS_BFTICU_BASE was removed because
the CONFIG_SYS_FPGA_BASE is already the base value for BFTICU registers.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
The changes introduced by commit 0abddf8 ``cmd_ide: enhance new
feature "CONFIG_IDE_AHB"'' caused compiler warnings like
cmd_ide.c: In function 'ide_init':
cmd_ide.c:716: warning: assignment from incompatible pointer type
Constify the respective function arguments to fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Although most IDE controller is designed to be connected to PCI bridge,
there are still some IDE controller support AHB interface for SoC design.
The driver implementation of these IDE-AHB controllers differ from other
IDE-PCI controller, some additional registers and commands access is required
during CMD/DATA I/O. Hence a configuration "CONFIG_IDE_AHB" in cmd_ide.c is
required to be defined to support these kinds of SoC controllers. Such as
Faraday's FTIDE020 series and Global Unichip's UINF-0301.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
In order to support boardId / hwkey lists, the u-boot default
environment has been updated: Added a script checkboardidlist
which checks the list of boardId / hwkey if the boadrId / hwkey
of the IVM is included in that list. This feature is used if you
got different HW variants but you only want to create one boot
package. E.g. supx5 board series.
Signed-off-by: Thomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Add:
- introduce "bootrunner" environment variable
This allows to execute consecutive different commands
specified in the list "subbootcmd". If one command fails
the command serie will stop.
- introduce environment variable "develop", "ramfs" and "release"
Each variable is one way to boot our linux. "develop" is for
development purpose and boots the SW via NFS. "release" is for
booting the linux image from flash, "ramfs" allows to load an SW
image via tftp into ram and executes from there
- introduce "addmem" variable, this command adds the used memory
for linux to the bootargs
- introduce "addvar" variable, this command adress for the /var
directory to the kernel command line
- introduce "setramfspram" and "setrootfsaddr" these calculation
were done if "ramfs" was used (only for debugging)
- introduce "tftpramfs" used for "ramfs" to load the image into
RAM (only for debugging)
Remove unneeded stuff:
- CONFIG_IO_MUXING is obsolete for keymile boards
- CONFIG_KM_DEF_ENV_PRIVATE is also obsolete
- define CONFIG_SYS_TEXT_BASE in board configs only
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
This patch adds last_stage_init to all keymile boards. And
in the last stage init some environment variables for u-boot
were set. Currently these are pnvramaddr, pram and var address.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
define KM_IVM_BUS and KM_ENV_BUS macros
KM_IVM_BUS is used to define the EEprom_ivm environment variable.
These macros allow the reuse of these I2C addresses in other code
locations.
remove unneeded code
On first HW versions the BOCO FPGA was behind a MUX device. These
HW versions are not supported anymore. And therefore this code can
be removed.
added LED initialization for SUEN3
The bootstat LED required to be initialized so to have a green
colour after start-up.
define CONFIG_SYS_TEXT_BASE
This is needed by the relocation code and is not the same for
our ARM BEC and thus needs to be defined.
remove memsize variable
An environment variable for memsize is not needed.
this can be get via the board info struct.
remove unneeded double access to bi_dram[i].size field
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Luca Haab <luca.haab@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
For the kmsupx5 a new header file was introduced km8321-common.h.
Now the common stuff from tuxa1, tuda1 and suvd3 was removed and
the new header file included.
The defines CONFIG_SYS_PIGGY_BASE and CONFIG_SYS_PIGGY_SIZE are
confusing. Because they actually describe the KMBEC FPGA values.
The KMBEC FPGA can be PRIO on kmeter1 or upio on mgcoge. Therefore
all the defines were renamed.
remove unneeded variable CONFIG_KM_DEF_NETDEV, as it is
already declared in keymile-common.h
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch renames the suen3 defines and functions to KM_KIRKWOOD
which is more generic and more precise, because these values
and functions where used by all suenX boards and not only suen3.
Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The Keymile SUPx5 board series is based on a PBEC8321 but
contains an additional PBUS FPGA (LPXF) on local bus CS2.
Signed-off-by: Thomas Reufer <thomas.reufer@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
First step for a cleanup of all header files for km8321 boards.
Signed-off-by: Thomas Reufer <thomas.reufer@keymile.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
The mgcoge2 board from keymile deploys two different processors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
The Kirwood based SUEN8 board from Keymile is at this stage
the same than the suen3 board. This patch adds the board
support for the suen8.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: Lukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount
This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch reworks all headerfiles for keymile boards. Furthermore
the environment variables are refactored.
Changes:
- introduce km-powerpc.h file and extract ppc specific parts to it
- move ARM specific options and vaiables to km_arm.h
- sort the environment variables to logical groups
- enhance the description of the environment variables
- remove KM specific HW key and board id from kernel command line
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
- adapt copyright string
- change bootdelay to 2 seconds
- set max number of command args to 32
- set I/O buffer size to 512
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
- use I/O accessors
-> For accessing the FPGA therefore a struct km_bec_fpga
is introduced.
- no longer externs needed
- to defines, that only select functions, don;t assign a
numeric value
- Codingstyle changes to prevent checkpatch errors/warnings
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
The MACH_TYPE SUEN3 is now to specific for keymile boards, because
other boards similar to suen3 will follow. So the MACH_SUEN3 was renamed
to MACH_KM_KIRKWOOD.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
CONFIG_SYS_BOOTMAPSZ has been 64M on these boards for some time so we
should also allow the kernel image to be up to 64M decompressed. This
also matches what we pass to the OS based on the ePAPR specification.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also added support to save env to spi flash in case of SPIBOOT.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Singed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The tsec driver was defining the default MDIO address as
the TSEC_BASE + 0x520, but on eTSEC2 controllers, the first
TSEC's registers are separated from the MDIO registers. Use
the existing MDIO_BASE_ADDR, instead.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make existing field b_max field in struct mmc unconditional
and use it instead of CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_bread
and mmc_bwrite.
Initialize b_max to CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_register
if it has not been initialized by the hw driver.
Initialize b_max to 0 in all callers to mmc_register.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Remove an empty board_early_init_f() from the MPC8641HPCN board.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the 'video-mode' environment variable (for Freescale chips that have a
DIU display controller) to designate the full video configuration. Previously,
the DIU driver used the 'monitor' variable, and it was used only to determine
the output video port.
The old definition of the "monitor" environment variable only determines
which video port to use for output. This variable was set to a number (0,
1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port. The
resolution was hard-coded into board-specific code. The Linux command-line
arguments needed to be hard-coded to the proper video definition string.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The following boards gain device tree support with this patch:
ca9x4_ct_vxp - Versatile Express
i.mx5 boards:
efikamx
mx51evk
mx53evk
OMAP boards:
devkit8000
igep0020
igep0030
omap3_overo
omap3_pandora
omap4_sdp3430
omap3_zoom1
omap3_zoom2
omap4_panda
omap4_sdp4430
Tegra boards:
Harmony
Signed-off-by: Grant Likely <grant.likely@linaro.org>
To make sure that the mux can be configured a deblocking sequence
is done before the mux configuration. After the mux switch the new leaf
of, the i2c tree must be again deblocked.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The P3041DS & P5020DS boards are almost identical (except for the
processor in them). Additionally they are based on the P4080DS board
design so we use the some board code for all 3 boards.
Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have
meaning on P3041DS/P5020DS. We utilize some of these for SERDES clock
configuration.
Additionally, the P3041DS/P5020DS support NAND.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes a wrong address define in corenet_ds.h (used by
P4080DS.h, P3041DS.h, P5020DS.h).
Since board/Freescale/corenet_ds/tlb.c does not use the
CONFIG_SYS_PCIE3_MEM_VIRT define (uses CONFIG_SYS_PCIE1_MEM_VIRT with a
fix offset instead) this has no effect to the functionality. But it may
be important for changes in the future?
Signed-off-by: Ralf Trübenbach <ralf.truebenbach@men.de>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we boot from a SD card use it for the environment as well.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
u-boot environments, esp. when boards are shared across multiple
users, can get pretty large and time consuming to visually parse.
The grepenv command this patch adds can be used in lieu of printenv
to facilitate searching. grepenv works like printenv but limits
its output only to environment strings (variable name and value
pairs) that match the user specified substring.
the following examples are on a board with a 5313 byte environment
that spans multiple screen pages:
Example 1: summarize ethernet configuration:
=> grepenv eth TSEC
etact=FM1@DTSEC2
eth=FM1@DTSEC4
ethact=FM1@DTSEC2
eth1addr=00:E0:0C:00:8b:01
eth2addr=00:E0:0C:00:8b:02
eth3addr=00:E0:0C:00:8b:03
eth4addr=00:E0:0C:00:8b:04
eth5addr=00:E0:0C:00:8b:05
eth6addr=00:E0:0C:00:8b:06
eth7addr=00:E0:0C:00:8b:07
eth8addr=00:E0:0C:00:8b:08
eth9addr=00:E0:0C:00:8b:09
ethaddr=00:E0:0C:00:8b:00
netdev=eth0
uprcw=setenv ethact $eth;setenv filename p4080ds/R_PPSXX_0xe/rcw_0xe_2sgmii_rev2_high.bin;setenv start 0xe8000000;protect off all;run upimage;protect on all
upuboot=setenv ethact $eth;setenv filename u-boot.bin;setenv start eff80000;protect off all;run upimage;protect on all
upucode=setenv ethact $eth;setenv filename fsl_fman_ucode_P4080_101_6.bin;setenv start 0xef000000;protect off all;run upimage;protect on all
usdboot=setenv ethact $eth;tftp 1000000 $dir/$bootfile;tftp 2000000 $dir/initramfs.cpio.gz.uboot;tftp c00000 $dir/p4080ds-usdpaa.dtb;setenv bootargs root=/dev/ram rw console=ttyS0,115200 $othbootargs;bootm 1000000 2000000 c00000;
=>
Example 2: detect unused env vars:
=> grepenv etact
etact=FM1@DTSEC2
=>
Example 3: reveal hardcoded variables; e.g., for fdtaddr:
=> grepenv fdtaddr
fdtaddr=c00000
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr
=> grep $fdtaddr
fdtaddr=c00000
my_boot=bootm 0x40000000 0x41000000 0x00c00000
my_dtb=tftp 0x00c00000 $prefix/p4080ds.dtb
nohvboot=tftp 1000000 $dir/$bootfile;tftp 2000000 $dir/$ramdiskfile;tftp c00000 $dir/$fdtfile;setenv bootargs root=/dev/ram rw ramdisk_size=0x10000000 console=ttyS0,115200;bootm 1000000 2000000 c00000;
=>
This patch also enables the grepenv command by default on
corenet_ds based boards (and repositions the DHCP command
entry to keep the list sorted).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
This patch defines all the needed symbols in the header file
and removes the now-unused config.mk in board directory.
Changes to board C file as requested.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
- fix board support following relocation changes
- switch to boards.cfg
- disable i2c to keep size under 128kiB (1 sector)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Move the header file and definitions of ftsmc020
static memory control unit from a320 SoC folder to
"drivers/mtd" folder.
This change will let other SoC which also use ftsmc020
could share the same header file.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Move the header file "ftsdmc020.h" (SDRAM Controller)
to "include/faraday" folder.
This change will let other SoC which also use ftsdmc020
could share the same header file.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
- update to new relocation code
- switch to boards.cfg
- get rid of LEGACY (still a little hack in .h to compile)
- add nand boot configuration
- boot tested for the following configurations :
9260 (64MB RAM & nor boot)
9260_nand (64MB RAM & nand boot)
9G20_128M (128MB RAM & nor boot)
9G20_nand_128M (128MB RAM & nand boot)
(nor boot is using lowlevel init)
Signed-off-by: Eric Bénard <eric@eukrea.com>
Board support for the DIG297 board manufactured by Comelit Group SpA.
It is a custom board based on the BeagleBoard <http://beagleboard.org/> by
Texas Instruments.
The board support is based on the BeagleBoard implementation.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Removed boot_flash_* extern variables.
boot_flash_type was totally unused. The other ones were actually constants, so
they have been replaced with #defines in the board config files.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The reset sequence/configuration for ehci is highly board specific,
so this will be done in the source for the board, instead of
introducing several CONFIG_* which would be needed to make those
few lines in beagle.c usable across different OMAP boards.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The default IGEP configuration doesn't do anything useful; using some
boot.scr search logic like BeagleBoard is much more useful.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
configuration
The default IGEP configuration doesn't do anything useful; using some
boot.scr search logic like BeagleBoard is much more useful.
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Move the header file and definitions of fttmr010
power control unit from a320 SoC folder to
"include/faraday" folder.
This change will let other SoC which also use fttmr010
could share the same header file.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Add asm support which is ususally used in lowlevel_init to set
power related parameters to sdram controller and static memory controller.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
1. ftpmu010.h: fix and add definitions
Enhanced for more features and asm related support
according to datasheet.
Note:
- FTPMU010_PDLLCR0_HCLKOUTDIS is "incorrect" in datasheet.
- FTPMU010_PDLLCR0_DLLFRANG is only 1 bit at bit #19. (not 20-19)
- FTPMU010_PDLLCR0_HCLKOUTDIS is 4 bits at bit #20. (not 24-21)
2. ftpmu010.c: enhance features and fix relocation
- The following functions is added for pmu features.
ftpmu010_mfpsr_select_dev()
ftpmu010_sdramhtc_set()
- This patch also fix the declare statement for relocation.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Add i2c_clk_enable in the cpu specific code, since previous platform it,
while new platform don't need. In the pantheon and armada100 platform,
this function is defined as NULL one.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
For better sharing with other platform other than pxa's,
it is more convenient to put the driver to the common place.
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
ftpmu010 related code has been moved to drivers/power/.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
CM-T3730 is exactly the same board as CM-T35, but it has
TI DM3730 SoC onboard and therefore some changes have to take place
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Use CONFIG_OMAP3_MMC in cm-t35 configuration file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
It is a low cost reference design based on Sitara AM3517 SoC from Texas Instruments
Please refer to <www.craneboard.org> for more details.
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Patch was updated by Jason Kridner <jkridner@beagleboard.org>:
* Use tabs to match style of other board revisions
* Only include board revisions that exist
* Default to the same configuration as the latest revision, but
without setting 'beaglerev'
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Using the new env import command it is possible to use plain text files instead
of script-images. Plain text files are much easier to handle.
E.g. If your boot.scr contains the following:
-----------------------------------
setenv dvimode 1024x768-16@60
run loaduimage
run mmcboot
-----------------------------------
you could create a file named uEnv.txt and use that instead of boot.scr:
-----------------------------------
dvimode=1024x768-16@60
uenvcmd=run loaduimage; run mmcboot
-----------------------------------
The variable uenvcmd (if existent) will be executed (using run) after uEnv.txt
was loaded. If uenvcmd doesn't exist the default boot sequence will be started,
therefore you could just use
-----------------------------------
dvimode=1024x768-16@60
-----------------------------------
as uEnv.txt because loaduimage and mmcboot is part of the default boot sequence
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Added LED driver using status_led. USR0 is set to monitor the boot
status. USR1 is set to be the green LED.
Included adding configuration and command to the default configuration.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.
Signed-off-by: Stefano Babic <sbabic@denx.de>
device tree for uboot arm support has already been enabled
in the master branch. This patch enable device tree support
for mx51/53 evk board for DT test.
Signed-off-by: Jason Liu <r64343@freescale.com>
The config.mk file in board directory is now obsolete and
should be removed. Add option for the IMX image into
boards.cfg
Signed-off-by: Stefano Babic <sbabic@denx.de>
If a regions is reserved in the fdt, then it should not be used. Add
the memreserve regions to the lmb so that u-boot doesn't use them to
store the initrd.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The previous patch makes u-boot use the full accessible size of ram as
the default boot mapped size if CONFIG_SYS_BOOTMAPSZ is not defined,
which means boot_relocate_fdt() can be changed to depend solely on
CONFIG_OF_LIBFDT.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This patch adds a function getenv_bootm_mapsize() for obtaining the
size of the early mapped region accessible by the kernel during early
boot. It defaults to CONFIG_SYS_BOOTMAPSZ, or if not defined,
defaults to getenv_bootm_size(), which in turn defaults to the size of
RAM.
getenv_bootm_mapsize() can also be overridden with a "bootm_mapsize"
environmental variable.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
For the calls to boot_relocate_fdt(), boot_get_cmdline(), and
boot_get_kbd(), the value of bootmem_base is always obtained by
calling getenv_bootm_low(). Since the value always comes from the
same source, the calling signature for those functions can be
simplified by making them call getenv_bootm_low() directly.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This func helps mmc_spi driver set correct speed for mmc/sd, as
mmc card needs 400KHz clock for spi mode initialization.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Use CONFIG_AUTOBOOT_KEYED on dlvision-10g so that booting can only be
stopped with well defined keypresses.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum.
This meant that drivers which used fsl_phy_enet_if to deal with
PHY interfaces would have to convert between the two (or we would have
to have them mirror each other, and deal with the ensuing maintenance
headache). Instead, we switch all clients of fsl_phy_enet_if over to
phy_interface_t, which should become the standard, anyway.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
This converts tsec to use the new PHY Lib. All of the old PHY support
is ripped out. The old MDIO driver is split off, and placed in
fsl_mdio.c. The initialization is modified to initialize the MDIO
driver as well. The powerpc config file is modified to configure PHYLIB
if TSEC_ENET is configured.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
The tsec driver had a bunch of PHY drivers already written. This
converts them all into PHY Lib drivers, and serves as the first
set of PHY drivers for PHY Lib.
While doing that, cleaned up a number of magic numbers (though
not all of them, as PHY vendors like to keep their numbers as
magical as possible). Also, noticed that almost all of the
vitesse/cicada PHYs had the same config/parse/startup functions,
so those have been collapsed into one.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme. The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support
The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).
The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.
We now have MDIO drivers and PHY drivers
An MDIO driver provides:
read
write
reset
A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed
The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()
Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)
We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.
We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,
we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.
Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Mostly putting a space between function name and "(", and
doing return (foo)
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
Most arches don't support OSE, and this is a new bootm target, so the
likelihood of any board actually wanting this today is fairly low.
Any board who actually wants this can enable it in the board-specific
config without making it a default bloat.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The first SEND_OP_COND (CMD1) command added is used to ask card capabilities.
After it an AND operation is done between card capabilities and host
capabilities (at the moment only for the voltage field).
Finally the correct value is sent to the MMC, waiting that the card
exits from busy state.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
It is recommended to check card status after these kind of commands.
This is done using CMD13 (SEND_STATUS) JEDEC command until
the card is ready.
In case of error the card status field is displayed.
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This patch supports mmc/sd card with spi interface. It is based on
the generic mmc framework. It works with SDHC and supports multi
blocks read/write.
The crc checksum on data packet is enabled with the def,
There is a subcomamnd "mmc_spi" to setup spi bus and cs at run time.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Andy Fleming <afleming@freescale.com>
CONFIG_ENV_SIZE = CONFIG_ENV_SECT_SIZE = 128kB but CONFIG_SYS_STACK_SIZE
is only 32kB resulting in saveenv causing a stack overflow and crashing
U-Boot. Resolve by reducing CONFIG_ENV_SIZE to 4kB
Also fix up CONFIG_SYS_MALLOC_LEN to correctly use environment sector
size and add some comments to the memory organisation configuration
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
1. Move header to include/faraday
2. Fix include path in ftwdt010_wdt.c
3. Fix function prototype and declaration to
- ftwdt010_wdt_settimeout
- ftwdt010_wdt_reset
- ftwdt010_wdt_disable
4. Add "#if definde (CONFIG_HW_WATCHDOG)" let user have flexibilty
to choose which better to his product.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Rename STANDALONE_LOAD_ADDR into CONFIG_STANDALONE_LOAD_ADDR
and allow that the architecture-specific default value gets
overwritten by defining the value in the board header file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Tsi Chung Liew <tsi-chung.liew@freescale.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There is a bug in the min and max macros in common.h which occurs if
Y is a larger type than X. For example, if Y is a 64-bit value and X
is a 32-bit value then Y will be truncated to 32-bits. This fix
matches what is done in the Linux kernel but without the additional
type checking present in the kernel version.
Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com>
This patch adds a new member to struct spi_flash (u16 sector_size)
and updates the spi flash drivers to start populating it.
This parameter can be used by spi flash commands that need to round
up units of operation to the flash's sector_size.
Having this number in one place also allows duplicated code to be
further collapsed into one common location (such as erase parameter
and the detected message).
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This reads the DIP switch on mgcoge. The DIP switch is connected to
the BFTICU (0x40000089) FPGA. If the DIP switch is set the environment
variable 'actual_bank' is set to 0 and starts the SW in bank0.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Add Intel E1000 82574L PCIe card support. Test on MPC8544DS
and MPC8572 board.
Add the missing contact information for future support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark
level register description has been changed:
9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00
25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and
PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as
1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from
CPC after PBL completes RCW and PBI phases.
Signed-off-by: Chunhe Lan <b25806@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Set default configuration to have SDHC controller enabled,
AUDIO enabled(codec clock sources is 12MHz) and disable TDM.
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the support for ATI graphics cards mutually exclusive with DIU.
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't really ever use Video cards on corenet_ds style boards and its
bloating our image which is close the its max size. Drop support and
also kill some defines for non-PNP PCI which we never use.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
renaming 85xx define CONFIG_NAND_OR_PRELIM to CONFIG_SYS_NAND_OR_PRELIM
and CONFIG_NAND_BR_PRELIM to CONFIG_SYS_NAND_BR_PRELIM to use the more
appropriate CONFIG_SYS prefix as well as be consistent with 83xx.
Signed-off-by: Matthew McClintock <msm@freescale.com>
cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
U-Boot itself takes up more than 0x40000 bytes, so we can't use that
sector for the environment. Move it down a page.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Have CONFIG_ENV_ADDR be based on CONFIG_ENV_OFFSET rather than the other
way around so that we can use CONFIG_ENV_OFFSET during build. It also
avoids a little address duplication.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Info about the hardware can be found here:
http://www.dilnetpc.com/dnp0086.htm
Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitydigital.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
collect code which protects default sectors in a function, called
flash_protect_default. So boardspecific code can call it too.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Clean up the macro defintions used to enable DIU (video) support on the
MPC8610HPCD and the MPC5121ADS so that they look more like the P1022DS,
which is newer. Add software cursor support to all three boards.
Also document the CONFIG_FSL_DIU_FB in the README.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We implement our own mmc_get_env_addr since the environment variables are
written to just after the u-boot image on SDCard, so we must read the MBR
to get the start address and code length of the u-boot image, then
calculate the address of the env.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The numeric constants in the switch statements are replaced by #defines
added to the common ddr_spd.h header. This dramatically improves the
readability of the switch statments.
In addition, a few of the longer lines were cleaned up, and the DDR2
type for an SO-RDIMM module was added to the DDR2 switch statement.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8572DS provides 2 USB ports with ULI1575. We enable USB storage
device support using PCI EHCI module.
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for 36-bit address map for NOR, SD, and SPI boot cfgs.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <priyanka.jain@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
