This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MALLOC_LEN
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
There are an assortment of hard-coded CONFIG_BOOTCOMMAND options in some
board headers. Rework these so that they do not add to the CONFIG
namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_MMC_ENV_DEV
CONFIG_SYS_MMC_ENV_PART
Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: Tom Rini <trini@konsulko.com>
I actually do not see this used these days because eMMC or NAND is used
for non-volatile devices. Dump the burden to maintain this crappy code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I increased the maximum U-Boot proper size from time to time, but
configs/uniphier_v7_defconfig hit the current limit 832KB.
Some historical info:
In the initial support, the max size was 512MB.
Commit 58d702274c ("ARM: uniphier: increase CONFIG_SYS_MONITOR_LEN")
increased it to 576KB, and commit 3ce5b1a8d8 ("ARM: uniphier: move
SPL stack address") moved the SPL stack location to avoid the memory
map conflict. It was the solution to increase the size without changing
the NOR boot image map.
commit 1a4bd3a095 ("ARM: uniphier: increase CONFIG_SYS_MONITOR_LEN
again") ended up with increasing the max size again, breaking the NOR
boot image map. The limit was set to 832KB, otherwise the SPL stack
would overwrite the U-Boot proper image:
CONFIG_SPL_STACK - CONFIG_SYS_UBOOT_BASE + sizeof(struct image_header) = 0xd0000
To increase CONFIG_SYS_MONITOR_LEN even more, the SPL stack must be
moved somewhere. I put it back to the original location prior to
commit 3ce5b1a8d8.
With this change, there is no more practical size limit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add handy macros:
- sdscript: source boot.scr in the file system of the SD media
- sdboot : boot the kernel using the images in the file system
of the SD media
- sdscript: update the boot firmware in the SD media
(in raw block sectors)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If the "source" command is not given the address, it uses
CONFIG_SYS_LOAD_ADDR, which is compile-time determined.
Using the "loadaddr" environment variable is handier because it is
relocated according to the memory base when CONFIG_POSITION_INDEPENDENT
is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The base of DRAM will be changed for the next generation SoC.
The addresses needed for booting the kernel should be shifted
according to the DRAM base.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The base of DRAM will be changed for the next generation SoC.
To support it along with existing SoCs in the single defconfig,
set 'loadaddr' at boot-time by adding the offset to the DRAM base.
CONFIG_SYS_LOAD_ADDR is still hard-coded for compilation, but the
value from environment variable 'loadaddr' should be used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The base address of DRAM was 0x80000000 for all the ARM SoCs of this
family in the past. It will be changed to 0x20000000 for a planned new
SoC. To support multiple SoCs by the single uniphier_v8_defconfig, the
base must be run-time determined.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is a remnant of commit f89d6133ee ("configs: move
CONFIG_SPL_TEXT_BASE to Kconfig").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Eventually these configuration items will be converted to Kconfig,
therefore there's little point in leaving commented-out versions of
them in include/configs.
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_BOOT
As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:
xilinx_zynqmp_zc1275_revB
xilinx_zynqmp_zc1751_xm018_dc4
xilinx_zynqmp_zc1751_xm019_dc5
xilinx_zynqmp_zcu100_revC
xilinx_zynqmp_zcu102_rev1_0
xilinx_zynqmp_zcu102_revA
xilinx_zynqmp_zcu102_revB
xilinx_zynqmp_zcu104_revA
xilinx_zynqmp_zcu104_revC
xilinx_zynqmp_zcu106_revA
xilinx_zynqmp_zcu111_revA
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is the same migration path as commit b6251db8c3 ("Kconfig:
Introduce USE_BOOTCOMMAND and migrate BOOTCOMMAND").
I also moved the description in README to the Kconfig help.
I ripped off the sentence about 'LWMON' since it is gone already.
I only let my boards migrate, leaving the rest to platform maintainers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some users might need additional setups before booting the kernel.
If there is found a file 'boot.scr', run it before invoking the
distro boot command.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some users might want to modify 'bootcmd' at compile-time by editing
include/configs/uniphier.h, but overwriting it at run-time makes it
impossible.
Instead, set 'bootdev' at run-time, which contains the boot device the
system is booting from, then indirectly reference it from 'bootcmd'.
It is up to users whether to override 'bootcmd'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
With the migration to distro-boot, the size of the U-Boot proper
image for uniphier_v7_defconfig exceeded the current limit, 576KB.
Increase it to 832KB.
CONFIG_SYS_UBOOT_BASE must be moved as well to avoid the image
over-wrap because the boot ROM of Pro4, Pro5, PXs2/LD6b loads
the SPL to the physical address 0x100000.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
Switch to the distro boot for UniPhier platform.
- Remove the environment vairalbes used to load images from raw
block devices.
- Keep the command to download images via tftp. This will be
useful to boot the kernel when no valid kernel image is ready
yet in the file system.
- Use root.cpio.gz instead of root.cpio.uboot because we always know
the file size of the init ramdisk; it is loaded via either a file
system or network.
- Rename fit_addr_r to kernel_addr_r, which the distro command
checks to get the load address of FIT image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
For booting Linux in the generic distro mechanism, cmd/pxe.c
retrieves the FDT file name from "fdtfile" environment variable.
Rename "fdt_file" to "fdtfile" for easier migration to distro boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, the address region, 0xf8000 - 0x100000, is used for SPL
stack for the 32bit SoCs. Because the U-Boot proper image starts
from 0x70000, the maximum size of the U-Boot proper image is 544KB
(0x70000 - 0xf8000) for the NOR boot mode. Now uniphier_v7_defconfig
is almost hitting this size limit. Changing CONFIG_SPL_STACK can
raise the size limit with less impact. With this, the size limit
will increase to 576KB (0x70000 - 0x100000). If we need to increase
it even more, we would be able to change CONFIG_SYS_UBOOT_BASE at the
cost of the flashing command changes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some boards support an SD card and an eMMC device at the same time.
Since both belong to 'mmc', they are identified by a device number.
When the device number of the eMMC is 1 instead 0, "mmc dev" command
must be performed to switch the target device before flashing images.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With the recent changes, the size of the U-Boot proper image for
uniphier_v7_defconfig exceeded the current limit, 512KB, then SPL
fails to load the whole of the U-Boot proper. Increase the size.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
The kernel size is getting bigger and bigger. Because the Android
common kernel is even bigger than the vanilla one, so images overlap
in the current memory layout.
Adjust the load address for a bigger kernel image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If a bigger EL32 is used, fip.bin can be larger than the currently
assumed boot firmware size. Adjust the update commands.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important. In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.
Signed-off-by: Tom Rini <trini@konsulko.com>
I do not see a good reason to do this by a CONFIG option that affects
all SoCs. The ram_size can be adjusted by dram_init() at run-time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
If the environment "verify" is set to n, the image verification
is entirely skipped. Remove it as a preparation for verified boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The default value of CONFIG_SYS_BOOTM_LEN, 0x800000, causes error
when uncompressing Image.gz out of FIT image.
Uncompressing Kernel Image ... Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
CONFIG_SMC911X
CONFIG_SMC911X_BASE
CONFIG_SMC911X_16_BIT
CONFIG_SMC911X_32_BIT
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that include/config_fallbacks.h define a sane fallback for
CONFIG_SYS_MAXARGS, we can drop the definition of this constant in all
configurations that were using the default value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that the fallback value of CONFIG_SYS_PBSIZE in
include/config_fallbacks.h has been adjusted, remove its definition
from a large number of board configuration files.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add the following options to drivers/misc/Kconfig:
SYS_I2C_EEPROM_ADDR
SYS_I2C_EEPROM_BUS
SYS_EEPROM_SIZE
SYS_EEPROM_PAGE_WRITE_BITS
SYS_EEPROM_PAGE_WRITE_DELAY_MS
SYS_I2C_EEPROM_ADDR_LEN
SYS_I2C_EEPROM_ADDR_OVERFLOW
This does not migrate any boards, but provides a foundations for
those who want/need these options
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate uniphier]
Signed-off-by: Tom Rini <trini@konsulko.com>
