Add a Synopsys Designware MIPI DSI host bridge driver, based on the
Rockchip version from rockchip/dw-mipi-dsi.c with phy & bridge APIs.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Display Serial Interface (DSI) host can usefully be modelled
as their own uclass.
DSI defines a serial bus and a communication protocol
between the host and the device (panel, bridge).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Mipi_display.c contains a set of dsi helpers.
This file is a copy of file drm_mipi_dsi.c (linux kernel).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
We don't need to pull in anything from the MIPS job so exclude that from
the new bcm job and make it clear it's building only ARM.
Signed-off-by: Tom Rini <trini@konsulko.com>
When hitting an invalid FAT cluster while reading a file always print an
error message and return an error code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At this point, all drivers that do not use CONFIG_BLK are past their
migration deadlines, so remove this config as it's no longer helpful and
hinders enhancing block drivers.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This define indicates if DM_SPI shall be supported in SPL. This allows
proper operation of DM converted SPI drivers in SPL, which use
#if !CONFIG_IS_ENABLED(DM_SPI) to also support not yet DM/DTS converted
boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
If an exception occurs in a loaded image and the relocation offset is
unknown, it is helpful to know the instructions pointed to by the
program counter. This patch adds the missing output.
A possible output is:
Code: 910c4021 aa1303e0 f9400662 d63f0040 (e7f7defb)
The parentheses indicate the instruction causing the exception.
The output can be disassembled using scripts/decodecode:
echo 'Code: 90000360 9100b800 94002782 17ffff8f (e7f7defb)' | \
ARCH=arm64 scripts/decodecode
Code: 90000360 9100b800 94002782 17ffff8f (e7f7defb)
All code
========
0: 90000360 adrp x0, 0x6c000
4: 9100b800 add x0, x0, #0x2e
8: 94002782 bl 0x9e10
c: 17ffff8f b 0xfffffffffffffe48
10:* e7f7defb .inst 0xe7f7defb ; undefined <-- trapping instruction
Code starting with the faulting instruction
===========================================
0: e7f7defb .inst 0xe7f7defb ; undefined
We already have implemented the same for armv7.
For testing command 'exception undefined' can be used.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This patch uses auto instead of decimal in simple_strtoul().
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
readb is unconditionally defined earlier in io.h, so there's no point
checking whether it's undefined.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
No ARM board seems to define __mem_pci - and if it did, one would get tons of
./arch/arm/include/asm/io.h:307:0: warning: "readl" redefined
warnings, because readl and friends are unconditionally defined
earlier in io.h. Moreover, the redefinitions lack the memory barriers
that the first definitions have. So I'm guessing this is practically
dead code.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This change allows setting pre-defined eMMC boot partition for SPL eMMC
booting. It is necessary in the case when one wants to boot (through falcon
boot) from eMMC after loading SPL from other memory (like SPI-NOR).
Signed-off-by: Mans Rullgard <mans@mansr.com>
[lukma: Edit the commit message]
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
This fixes a wrongly indented block of code.
Signed-off-by: Mans Rullgard <mans@mansr.com>
[lukma: Make the commit message more verbose]
Signed-off-by: Lukasz Majewski <lukma@denx.de>
If there is any failure during IOdelay recalibration sequence, IOs are
not guaranteed to behave as expected. So hang on any failure during the
sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
When an error is reported in __recalibrate_iodelay_start(), de-isolation
of IO doesn't happen. Because of this, undefined behaviour is observed
on many peripherals without any error. So make sure io is out of isolation
at the end of iodelay recalibration.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently "bootcmd" does not work as intended but instead prints MMC usage
information and goes directly to "nandboot".
Follow what the commit 669681104d ("configs: Fix usage of mmc rescan")
does for other boards prior to support for TechNexion TAO3530 SoM was
added.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
spl_dm_init is failing as usb to be probed with the following error:
"omap_dwc3@483c0000: ret=-2"
Enable usb to make spl boot on am43xx devices
Reported-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Main uart0 is used as debug console by both R5SPL and A72 bootloader and
Linux. So mark it as shared device so that power-domain request is
successful by both cores.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM335x-ICE boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM43xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AM57xx-IDK boards contain the CDCE913 clock synthesizer, and their
reset crystal capacitance load value of 10pF is wrong leading into
lost packets in certain networking tests. Add DT data for this
device, and probe it from the board file to program the crystal
capacitance load value to 0pF to avoid any problems.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add support for CDCE913/925/937/949 family of devices. These are modular
PLL-based low cost, high performance, programmable clock synthesizers,
multipliers and dividers. They generate up to 9 output clocks from a
single input frequency. The initial version of the driver does not
support programming of the PLLs, and thus they run in the bypass mode
only. The code is loosely based on the linux kernel cdce9xx driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Print the board name and ver along with the DT Model.
While at it print the ver for all the detected daughter cards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Power-domain is enabled by default in device_probe. am654 mmc driver
is enabling power-domain again in probe. As the second call is
redundant, drop power_domain_on from probe.
Tested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When running 'run_fit' the FIT file should have been loaded at
'addr_fit', although at this point they should be the same
use this variable instead of 'loadaddr'.
Signed-off-by: Andrew F. Davis <afd@ti.com>
- add BOARD_LATE_INIT function calls in board.c
- add swi_status detection in board.c
- mux: add guardian interfaces to single pinmux structure
- am33xx, kconfig: add BOARD_LATE_INIT for GUARDIAN board
Signed-off-by: Moses Christopher <BollavarapuMoses.Christopher@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If the ECC is enabled over the entire memory region, we need to ensure
the printf/put calls do not modify the stack after ECC is disabled.
Moved the printf/put statements after ECC is enabled.
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Before the priming begins, we need to disable RMW (Read Modify Write)
and disable ECC verification for read accesses. By default, the EMIF
tool enables RMW and read accesses in the EMIF_ECC_CTRL_REG.
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
If ECC is enabled, we need to ensure interleaving is disabled for higher
address space.
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
ecc_address_range registers contains the start address and end address
of the DDR address space. But the ddr cmd driver is assuming the register
contains the start address and size of the DDR address space. Because
of this some valid ecc addresses are errored out as invalid address.
Fix this calculation.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
ecc_address_range registers contains the start address and end address
of the DDR address space. But the ddr driver is assuming the register
contains the start address and size of the DDR address space. Because
of this the ecc enabling is failing for the 2nd range of ecc addresses.
Fix this calculation.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Regulator should not be enabled at probe time if regulator-boot-on
property is not in the dt node.
"enable-active-high" property is only used to indicate the GPIO
polarity.
See kernel documentation :
- Documentation/devicetree/bindings/regulator/fixed-regulator.yaml
- Documentation/devicetree/bindings/regulator/gpio-regulator.yaml
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In 32bits mode upper bits need to be set to 0, otherwise controller will
try to DMA into not existing memory and stops with error.
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Oleksandr Rybalko <ray@ddteam.net>
This adds a document for tphy which supports physical layer
functionality for a number of controllers on MediaTek SoCs,
such as, USB2.0, USB3.0, PCIe, and SATA.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
