Initial support for Fairchild's 8 bit I2C gpio expander FXL6408.
The CONFIG_FXL6408_GPIO define enables support for such devices.
Based on: https://patchwork.kernel.org/patch/9148419/
Signed-off-by: Oleksandr Suvorov <cryosay@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYeg7sQAKCRDKSWXLKUoM
IVhJAKCAiNx/joEeFBJ0XgThtJzFhCjdMwCfYKY9Ewz4L0n2I56lDgR3UJroct0=
=HtB+
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
ZynqMP modepin driver has capability to get/set/check status of modepin
gpios. These modepins are accessed using xilinx firmware. In modepin
register, [3:0] bits set direction, [7:4] bits read IO, [11:8] bits
set/clear IO.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/2d802d98fd56d95d764532a33e844d935e0cebb3.1635505900.git.michal.simek@xilinx.com
At present we have SPL_GPIO and TPL_GPIO but not piain GPIO. This
works because there is a special build rule in Makefile that always
includes the drivers/gpio directory.
It is better to have all driver directories included by drivers/Makefile
and there is already a rule in there for this purpose. It just needs a
Kconfig for U-Boot proper, so add one.
Enable the option always for now, since this mimics current behaviour.
This can be updated once DM_GPIO is used everywhere.
Signed-off-by: Simon Glass <sjg@chromium.org>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce driver for I2C based MCP230xx GPIO chips, which are
quite common and already well supported by the Linux kernel.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Nomadik GPIO is a fairly simple GPIO module used in the ST-Ericsson
Ux500 SoCs (and some older Nomadik SoCs). It uses registers where
each GPIO is represented as a single bit, plus "set" and "clear"
registers that allow updating the state without having to read the
existing state.
The driver implements support for it for use together with DM_GPIO
and the existing ste-dbx5x0.dtsi device tree.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
pca953x also depends on i2c that's why add dependency to Kconfig.
Where GPIO is enabled but I2C compilation error pops up.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The Armada driver also works on Nedap's custom Kirkwood board with a
Marvell 88F6180 CPU. The original commit of that driver,
commit 704d9a645e ("gpio: Add DM GPIO driver for Marvell MVEBU"),
also mentions that this driver would be suitable for Kirkwood. This
does not completely replace the Kirkwood specific driver as there
are still boards depending on that driver.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Stefan Roese <sr@denx.de>,
Reviewed-by: Stefan Roese <sr@denx.de>
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for GPIO controllers found on Octeon II/III and Octeon TX
TX2 SoC platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- livetree API (dev_read_...) is used instead of fdt one (fdt...).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
dm_gpio_lookup_name() searches for a gpio through
the bank name. But we have also gpio labels, and it
makes sense to search for a gpio also in the labels
we have defined, if no gpio is found through the
bank name definition.
This is useful for example if you have a wp pin on
different gpios on different board versions.
If dm_gpio_lookup_name() searches also for the gpio labels,
you can give the gpio an unique label name and search
for this label, and do not need to differ between
board revisions.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Don't enable by default]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some SoCs in the mpc83xx family, e.g. mpc8309, have a dedicated spi
chip select, SPISEL_BOOT, that is used by the boot code to boot from
flash.
This chip select will typically be used to select a SPI boot
flash. The SPISEL_BOOT signal is controlled by a single bit in the
SPI_CS register.
Implement a gpio driver for the spi chip select register. This allows a
spi driver capable of using gpios as chip select, to bind a chip select
to SPISEL_BOOT.
It may be a little odd to do this as a GPIO driver, since the signal
is neither GP or I, but it is quite convenient to present it to the
spi driver that way. The alternative it to teach mpc8xxx_spi to handle
the SPISEL_BOOT signal itself (that is how it's done in the linux
kernel, see commit 69b921acae8a)
Signed-off-by: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
DM_GPIO based GPIO controller driver for CAxxxx SoCs.
This driver support multiple CPU architectures and
Cortina Access SoC platforms.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Add a GPIO driver which uses the pinctrl driver to access the pad
information. This driver relies on the GPIO nodes being subnodes to the
pinctrl device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds support for gpio driver for versal platform
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds a DM based driver model for gpio controller present in
FU540-C000 SoC on HiFive Unleashed A00 board. This SoC has one GPIO
bank and 16 GPIO lines in total, out of which GPIO0 to GPIO9 and
GPIO15 are routed to the J1 header on the board.
This implementation is ported from linux based gpio driver submitted
for review by Wesley W. Terpstra <wesley@sifive.com> and/or Atish Patra
<atish.patra@wdc.com> (many thanks !!). The linux driver can be referred
here [1]
[1]: https://lkml.org/lkml/2018/10/9/1103
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This converts the following to Kconfig:
CONFIG_MXS_GPIO
Travis-CI: https://travis-ci.org/lmajewski/u-boot-dfu/builds/571260789
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
recently added gpio hog patch was "in discussion"
state with Simon Glass. This patch now adds most
of comments from Simon Glass.
Signed-off-by: Heiko Schocher <hs@denx.de>
Probably for no particular reason SUNXI_GPIO was still defined the "old
way", in header files only.
Introduce SUNXI_GPIO to the Kconfig file in drivers/gpio to remove
another line from our dreadful config_whitelist.txt.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
add gpio-hog support. GPIO hogging is a mechanism
providing automatic GPIO request and configuration
as part of the gpio-controller's driver probe function.
for more infos see:
doc/device-tree-bindings/gpio/gpio.txt
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Michal Simek <michal.simek@xilinx.com> (zcu102)
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
As this driver is used on stm32f4/f7/h7 and stm32mp1
SoCs, rename it with a more generic name.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Add GPIO driver for RZ/A1 SoC. The IP is very different from the
R-Car Gen2/Gen3 one already present in the tree, hence a custom
driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Currently mach-mt7620 contains only support for mt7628. To avoid confusion,
rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms.
MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628
because they do not share the same lowlevel codes.
Dependencies of four drivers are changed to SOC_MT7628 as these drivers
are only used by MT7628.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
With the new mscc_bb_spi.c driver, there is no longer use for the
gpio-mscc-bitbang-spi.c driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This add support for the the MSCC serial GPIO driver in MSCC
VCoreIII-based SOCs.
By using a serial interface, the SIO controller significantly extends
the number of available GPIOs with a minimum number of additional pins
on the device. The primary purpose of the SIO controller is to connect
control signals from SFP modules and to act as an LED controller.
This adds the base driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
The VCore III SoCs such as the Luton but also the Ocelot can remap an SPI
flash directly in memory. However, for writing in the flash the
communication has to be done by software.
Each of the signal used for the SPI are exposed in a single register. In
order to be able to use the soft-spi driver, the management of this pin
is done through this simple gpio driver.
Even if the main purpose of this driver is to be used by soft-spi, it can
still be used as a normal gpio driver but with limitation: for example
the first pin can't be used as output.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds GPIO support for the Mediatek MT7621 SoC, tested on
MT7688 (Gardena smart-gateway). The driver is loosly based on the
Linux kernel version.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
[fixed checkpatch.pl warnings: Prefer 'unsigned int' to bare use of 'unsigned']
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.
GPIO reset is handled via sysreset with adding this fragment to DT.
gpio-restart {
compatible = "gpio-restart";
gpios = <&reset_gpio 0 0 0>;
/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};
hard-reset-gpio property is not documented and also handled.
Conversion is required.
Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The naming with "UART" is obviously wrong, we fix this here.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch added Kconfig support for CONFIG_XILINX_GPIO
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
