Sync with other rockchip SoCs, use board_debug_uart_init() to
init default UART iomux.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch sets the PLL of CPU cluster B (BPLL) to 600 MHz.
This decreases the boot time of Linux 4.19 by about 8%.
The 600 MHz are inspired by the 600 MHz used for LPLL initialization
(came in with commit 9f636a249c).
Tested on RK3399-Q7 on Haikou base board.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds the definitions need to use the USB OTG in rv1108
board. This has been tested using USB Mass Storage to export and
program a eMMC device.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Like it is done for other Rockchip SoCs, introduce a board_usb_init()
function so that USB OTG can be functional on rv1108 too.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This adds the pinctrl handles to enable the use of eMMC on custom
boards (as minievk) and makes it easier for later addition.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Make adjustments to the rv1108 clock driver in order to align it
with the internal Rockchip version.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Some SanDisk Ultra cards trigger intermittent errors on detection
resulting in an -EOPNOTSUPP, when running at 50MHz.
Waveform analysis suggest that the level shifters that are used on the
RK3399-Q7 module (for voltage translation between the on-module
voltages and the 3.3V required on the card-edge) don't handle clock
rates at or above 48MHz properly. This change reduces the maximum
frequency on the external SD-interface to 40MHz (for a safety margin
of 20%).
Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
The RK3399 SPL has two cases that may end in a hard-stop: if either
the pinctrl can not be initialised or if the DRAM fails to initialise.
Both have previously not triggered an error message unless DEBUG was
defined (i.e. both used debug() to print the error).
This converts both error messages to be printed using pr_err() to
ensure that some output points to the cause of the hard-stop.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Commit 7a6d7d3e12 ("rockchip: pinctrl: rk3188: Move the iomux definitions
into pinctrl-driver") moved the iomux settings out of the grf header
to prevent conflicts with the iomux definitions of other rockchip socs.
This also breaks the early uart setup, as the iomux for uart2 are needed.
To fix that just put the tiny amount of needed iomux definitions next to
the early uart code.
Fixes: 7a6d7d3e12 ("rockchip: pinctrl: rk3188: Move the iomux definitions into pinctrl-driver")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip socs can route the debug uart pins through the d+ and d- pins
of one specific usbphy per soc. Add a config option and implement the
setting on the rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Fixed up to mark grf as maybe unused:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch prevents disabling the FPGA bridges when
SPL or U-Boot is executed from FPGA onchip RAM.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This fixes the board's dts to supply SPL with QSPI info.
The EBV Socrates board has DIP switches to boot from SD card or
QSPI, so let's fix its defconfig to work for both cases.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add -u-boot.dtsi files to keep the current U-Boot behaviour:
- add u-boot,dm-pre-reloc where required
- disable watchdog
- set uart clock frequency
- add gpio bank-name properties
where appropriate:
- make qspi work (add alias for spi0, fix compatible for flash)
- enable usb (status okay, add alias for udc0)
Adapt board dts files that are not in Linux to keep their old
behaviour.
Change licenses to SPDX.
(Patman warnings/errors are in 1:1 copied files from Linux)
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Linux uses "cdns,qspi-nor" as compatible string for the cadence
qspi driver, so change driver, docs and all device trees.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This patch adds pinctrl support for MT7629 SoC. The IO core found on
the SoC has the registers for pinctrl, pinconf and gpio mixed up in
the same register range. Hence the driver also implements the gpio
functionality through UCLASS_GPIO.
This also creates a common file as there might be other chips that use
the same binding and driver, then being a little more abstract could
help in the long run.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a general board file based on MT7623 SoCs from MediaTek.
As this u-boot is loaded by MTK proprietary preloader, there is no
low level initializtion codes.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a general board file based on MT7629 SoCs from MediaTek.
Apart from the generic parts (cpu) we add some low level init codes
and initialize the early clocks.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds device tree for MT7623 development board - Bananapi R2
Detailed hardware information for BPI-R2 which could be found on
http://wiki.banana-pi.org/Banana_Pi_BPI-R2.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds MT7629 device tree and the includes it needs.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add that node path in u-boot overlay dtsi file for now to keep
am335x-chiliboard.dts in sync with Linux.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Import chiliSOM and chiliboard dts files from Linux v4.19. They will
be used after transition to driver model and device-tree based boot.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some erratum workarounds call into C code before the stack
is setup, this can lead to values pushed onto the stack
being lost, firewall exceptions, and other undefined behavior.
Setup a temporary stack to allow these functions to work
correctly.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Based on the MCU R5 efuse settings, R5F cores in MCU domain
either work in split mode or in lock step mode.
If efuse settings are in lockstep mode: ROM release R5 cores
and SPL continues to run on the R5 core is lockstep mode.
If efuse settings are in split mode: ROM releases both the R5
cores simultaneously and allow SPL to run on both the cores.
In this case it is bootloader's responsibility to detect core
1 and park it. Else both the core will be running bootloader
independently which might result in an unexpected behaviour.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Amlogic Meson SoCs ROM supports a boot over USB with a custom protocol.
When no other boot medium are available (or by forcing the USB mode), the
ROM sets the primary USB port as device mode and waits for a Host to
enumerate.
When enumerated, a custom protocol described at [1] permits writing to
memory and execute some specific FIP init code to run the loaded
Arm Trusted Firmware BL2 and BL3 stages before running the BL33 stage.
In this mode, we can load different binaries that can be used by U-boot
like a script image file.
This adds support for a custom USB boot stage only available when the
boot mode is USB and the script file at a pre-defined address is valid.
This support was heavily copied from the Sunxi Allwinner FEL U-Boot support.
The tool pyamlboot described at [2], permits using this boot mode on boards
exposing the first USB port, either as OTG or Host port.
[1] https://github.com/superna9999/pyamlboot/blob/master/PROTOCOL.md
[2] https://github.com/superna9999/pyamlboot/blob/master/README.md
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Now we have moved all the Amlogic board support to common generic board code,
we can move the identical board_init() and ft_board_setup() functions to
weak functions into the board-common mach-meson file.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch adds a minimal clock driver for the Amlogic AXG SoC to handle
the basic gates and PLLs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Synchronize the Amlogic AXG Device Tree files and bindings include from
the recent Linux 4.20-rc1, because it includes patches fixing support for
U-boot.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch adds support for the Amlogic AXG SoC, which is very close from
the Amlogic GXL SoCs with :
- Same 4xCortex-A53 CPUs but clocked at 1.2GHZ max
- DDR Interface limited to DDR4 16bit
- The whole physical register address space has been moved to 0xfxxxxxxx
- The pinctrl setup has changed
- The clock tree is different enough to use a different driver
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We are about to add support for the Amlogic AXG SoC. While very close to
the Gx SoC family, we will need to handle a few thing which are different
in this SoC. Rework the meson arch directory to prepare for this.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework the board SYS_BOARD, SYS_VENDOR and SYS_CONFIG_NAME setup by moving
the board Kconfig into the mach-meson Kconfig to make it easier to add
new boards for a SoC architecture and add a custom config header or custom
board handler for a platform.
This drops the board CONFIGs and the duplicate boards configs headers in
favor of a single meson64.h config header.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The nanopi-k2 and the odroid-c2 are similar enough to be supported
by the same u-boot board. This change use odroid-c2 u-boot board
for the nanopi-k2 as well. Dedicated defconfig are kept to customize
the names and device tree.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Khadas vim2 derive from amlogic s912 reference design (Q200).
This patch moves the khadas-vim2 board support to a generic Q200 board,
while keeping a dedicated defconfig to customize the names and device tree.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Khadas vim and the libretech aml-s905x-cc (aka Potato) derive
from amlogic s905x reference design (P212).
All the code in these board is a copy/paste from the p212, which is
tedious to maintain. This change use p212 u-boot board for all these
boards, while keeping a dedicated defconfig to customize the names
and device tree.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Even if multiple board are selected through Kconfig, u-boot will only
compile one. This makes sense since compiling these targets will export
global symbols, such as board_init()
The change rework amlogic Kconfig so only one board may be selected at
a time
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When we initialize the memory we need to autodetect rank and size
but this can happen only if we send the proper reset to both
memory module including cke signal.
For this reason we need initialize the physical on both channel because
we need to presume that both are connected. This way let the CLKE to be
activated at the right time with the memory reset coming from the cpu
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Using new mode improves stability of eMMC and SD cards. Without
it SPL fails to load u-boot from SD on Pinebook.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@openedev.com>
Allwinner A64 has new mode but doesn't have a mode switch in CCM,
and CCM_MMC_CTRL_MODE_SEL_NEW is not defined, so compilation fails
if MMC_SUNXI_HAS_NEW_MODE is enabled
Introduce new MMC_SUNXI_HAS_MODE_SWITCH option to be able to ifdef usage
of CCM_MMC_CTRL_MODE_SEL_NEW
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
At present these functions return 0 on success. For some devices we want
to know how many bytes were transferred. It seems useful to adjust the API
to be more like the POSIX read() and write() functions.
Update these two methods, a test and all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The SolidRun Clearfog GT-8K is based on Armada 8040.
https://wiki.solid-run.com/doku.php?id=products:a8040:clearfoggt8k
The config file is identical to the Macchiatobin one
(mvebu_mcbin-88f8040_defconfig) with only the default device-tree
changed.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Some Armada 8K boards like Macchiatobin and Clearfog GT-8K use RAM from
external DIMM. Hard coding the RAM size in the device-tree is not
convenient. Fortunately, the ATF that initializes the RAM knows the size
of RAM, and U-Boot can query the ATF using a SMC call.
The ATF maps the lower 3G of RAM starting at address 0. Higher RAM is
mapped at 4G. This leaves a 1G hole between 3G and 4G for IO
peripherals. Use a second bi_dram[] entry to describe the higher RAM
area. As a result, CONFIG_NR_DRAM_BANKS must be set to 2 to use more
than 3GB RAM.
This code in this commit is mostly taken from downstream Marvell U-Boot
code by Grzegorz Jaszczyk.
Cc: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
The kernel added SZ_4G macro in commit f2b9ba871b (arm64/kernel: kaslr:
reduce module randomization range to 4 GB).
Include linux/const.h for the _AC macro.
Drop a local SZ_4G definition in tegra code.
Cc: Tom Warren <twarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Drop the _AC and UL macros from common.h. Linux headers is the original
source of this macro, so keep its definition in the same header.
Update existing users of these macros to include const.h directly.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Rick Chen <rick@andestech.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Sync the k3-am654 specific dts files from Linux next with tag
20181019. This changes are in queue for Linux v4.20-rc1
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In SPL, DDR should be made available by the end of board_init_f()
so that apis in board_init_r() can use ddr. Adding support
for triggering DDR initialization from board_init_f().
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
