Commit graph

319 commits

Author SHA1 Message Date
Albert ARIBAUD
6d4511b2c6 Merge 'u-boot-microblaze/zynq' into (u-boot-arm/master'
Conflicts:
	arch/arm/include/asm/arch-zynq/hardware.h

The conflict above was trivial and solved during merge.
2013-09-03 14:01:02 +02:00
Michal Simek
2d83d33a51 zynq: Enable axi ethernet and emaclite driver initialization
Zynq can have axi ethernet and emaclite IPs in programmable
logic.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2013-08-12 08:59:56 +02:00
Michal Simek
148ba55cc6 zynq: Add new ddrc driver for ECC support
The first 1MB is not initialized by first stage bootloader.
Check if memory is setup to 16bit mode and ECC is enabled.
If it is, clear the first 1MB.
Also u-boot should report only the half size of memory.

Acked-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-08-12 08:59:55 +02:00
Michal Simek
fd2b10b6d6 fpga: zynqpl: Add support for zc7100 device.
- Add support for zc7100 device.
- FPGA programming on few of the SOC(zc7100) takes more
  than 1sec, hence increased the program time by 4sec to
  sync' all soc's.

Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-08-12 08:01:50 +02:00
Stephen Warren
6697d55862 xilinx: move microblaze-generic .dts to standard location
Aside from microblaze, all other SoCs/boards/vendors store their DT files
in board/$vendor/dts/$soc-$board.dts. Move microblaze-generic.dts to this
location for consistency.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <monstr@monstr.eu>
2013-08-02 18:29:32 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Albert ARIBAUD
a19b0dd62d Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	common/cmd_fpga.c
	drivers/usb/host/ohci-at91.c
2013-05-30 14:45:06 +02:00
Albert ARIBAUD
e825b100d2 Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master' 2013-05-11 00:06:03 +02:00
Michal Simek
4e779ad2e5 gpio: Add support for microblaze xilinx GPIO
Microblaze uses gpio which is connected to the system reset.
Currently gpio subsystem wasn't used for it.

Add gpio driver and change Microblaze reset logic to be done
via gpio subsystem.

There are various configurations which Microblaze can have
that's why gpio_alloc/gpio_alloc_dual(for dual channel)
function has been introduced and gpio can be allocated
dynamically.

Adding several gpios IP is also possible and supported.

For listing gpio configuration please use "gpio status" command

This patch also remove one compilation warning:
microblaze-generic.c: In function 'do_reset':
microblaze-generic.c:38:47: warning: operation on '*1073741824u'
 may be undefined [-Wsequence-point]

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-05-09 11:20:08 +02:00
Michal Simek
d5dae85f23 fpga: zynq: Add support for loading bitstream
Devcfg device requires to load bitstream in binary format.
But u-boot also has an option for loading bitstream in bit
format. Let's handle both cases by zynqpl driver.
Also add suport for loading partial bitstreams.

The first driver version was done by:
Joe Hershberger <joe.hershberger@ni.com>

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-05-06 10:41:24 +02:00
Michal Simek
293eb33fcb mmc: Add support for Xilinx Zynq sdhci controller
Add support for SD, MMC and eMMC card on Xilinx Zynq.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:39:27 +02:00
David Andrey
01fbf31042 net: gem: Preserve clk on emio interface
Avoid overwriting GEMx_RCLK_CTRL and GEMx_CLK_CTRL
if the Ethernet interface is connect on EMIO

Do not enable emio for this standard board configuration for now.

Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:39:24 +02:00
David Andrey
117cd4cc10 net: gem: Pass phy address to init
Pass the PHY address to the driver init to
allow parallel use of both interfaces

Signed-off-by: David Andrey <david.andrey@netmodule.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:39:23 +02:00
Michal Simek
7193653e8d zynq: Move macros to hardware.h
Add all fixed addresses to hardware.h and change petalinux
configuration to support this.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:39:21 +02:00
Michal Simek
0f21f98dd4 watchdog: Add support for Xilinx Microblaze watchdog
Watchdog can be used on Microblaze, PPC and Zynq hw designs.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
2013-04-30 11:22:43 +02:00
Michal Simek
8848668e13 microblaze: Disable all cpu features before reset
Fix microblaze soft reset function and disable
all cpu features. Especially disable caches because
IRQs were off by disable_interrupts().

Reported-by: John Williams <john.williams@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-04-30 11:22:42 +02:00
Michal Simek
b364727abb microblaze: Fix reset function
Remove CONFIG_SYS_RESET_ADDRESS macro.
It was there from historical point of view
when soft reset was just jump to u-boot text start
(not used right now).

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-04-30 11:22:38 +02:00
Michal Simek
14d315b8b3 microblaze: Remove FSL support from generic board
This code was targetting one specific Microblaze platform
configuration which is obsolete and fsl bus isn't used
in this way.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-02-04 12:09:50 +01:00
Michal Simek
151eeeb275 board: xilinx: Remove common folder
All these files was used for ancient xilinx drivers
which are finally gone.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
2013-02-04 12:09:49 +01:00
Michal Simek
74b87c4ceb board: xilinx: Remove unused ancient i2c driver
There is new driver in the driver folder.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
2013-02-04 12:09:49 +01:00
Michal Simek
f22651cfc4 xilinx: Add new Zynq board
Add support for Xilinx Zynq board.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
CC: Joe Hershberger <joe.hershberger@gmail.com>
2012-10-04 16:57:36 +02:00
Michal Simek
2380b8f529 microblaze: Clean microblaze initialization
Move board specific function to board_init function in board/ folder
Remove externs from generic board.c
Use board_init_f function in board.c file.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stephan Linz <linz@li-pro.net>
2012-09-11 09:24:58 +02:00
Stephan Linz
920c358781 microblaze: Wire up dts configuration
- enable OF control and embedded OF
    - set default device tree file name to 'microblaze'
    - add CPP to dtc proxy: board/xilinx/dts/microblaze.dts
    - add an empty but processable dts for microblaze-generic

Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-07-10 10:01:29 +02:00
Michal Simek
2e65b44c0f microblaze: Move individual board linker scripts to common script in cpu tree.
Unification for all microblaze boards.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2012-07-09 10:44:27 +02:00
Stephan Linz
3ceecef14e microblaze: Wire up LL_TEMAC driver initialization
Initialize ll_temac driver.

Reported-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-04-04 09:36:44 -05:00
Stephan Linz
20637888df microblaze: Add faked LL_TEMAC driver configuration
Expand the specific configuration for the microblaze-generic
board in xparameters.h with a faked setup to enable the
LL_TEMAC driver.

Note: From now the microblaze-generic board is no longer a
valid board configuration for a real piece of hardware. Rather
than, we use the file config.mk and xparameters.h as a faked
board configuration to force the compilation of all potential
driver code for Microblaze systems.

Signed-off-by: Stephan Linz <linz@li-pro.net>
2012-04-04 09:36:38 -05:00
Michal Simek
e634138e73 microblaze: Wire up axi_ethernet driver initialization
Initialize axi_ethernet driver.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-24 07:50:21 +02:00
Mike Frysinger
daaaf0285d net: xilinx_enet: drop unused !NET_MULTI driver
This driver doesn't support the NET_MULTI framework, and I can't find
any boards/configs/files that reference this subdir, so punt it all.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-23 23:34:20 +02:00
Michal Simek
c1044a1ec1 net: emaclite: Move RX/TX ping pong initialization to
Init RX/TX ping pong directly from board not in the driver.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-23 23:32:44 +02:00
Mike Frysinger
464c79207c punt unused clean/distclean targets
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used.  Punt them all.

MAKEALL didn't report any errors related to this that I could see.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-15 22:20:36 +02:00
Scott Wood
83b7e2a7f2 Handle most LDSCRIPT setting centrally
Currently, some linker scripts are found by common code in config.mk.
Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is
sometimes in arch config.mk and sometimes in board config.mk.  Some
are found using an arch-specific rule for looking in CPUDIR, etc.

Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL
when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact
that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds.

Replace all of this -- except for a handful of boards that are actually
selecting a linker script in a unique way -- with centralized ldscript
finding.

If board code specifies LDSCRIPT, that will be used.
Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used.

If neither of these are specified, then the central config.mk will
check for the existence of the following, in order:

$(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/board/$(BOARDDIR)/u-boot.lds
$(TOPDIR)/$(CPUDIR)/u-boot.lds

Some boards (sc3, cm5200, munices) provided their own u-boot.lds that
were dead code, because they were overridden by a CPUDIR u-boot.lds under
the old powerpc rules.  These boards' own u-boot.lds have bitrotted and
no longer work -- these lds files have been removed.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
2011-04-30 00:59:47 +02:00
Ricardo Ribalda Delgado
7e4c3a41ce xilinx-ppc4xx-generic: Fix Makefile to work with MAKEALL
config.mk only mkdirs $(obj), but we have objects shared with other
boards located on other dirs.

This patch mkdirs the needed dirs for the xlnx-generic boards.

Signed-off-by: Stefan Roese <sr@denx.de>
2011-01-11 10:58:55 +01:00
Ricardo Ribalda Delgado
d20b999115 xilinx-ppc4xx-generic: Use common u-boot.lds
Use common ppc4xx linker script for xilinx ppc440 and ppc405 related boards.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2010-12-17 09:44:40 +01:00
Mike Frysinger
882b7d726f do_reset: unify duplicate prototypes
The duplication of the do_reset prototype has gotten out of hand,
and they're not all in sync.  Unify them all in command.h.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-11-28 21:47:24 +01:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Wolfgang Denk
2ae1824196 Makefile: move all Power Architecture boards into boards.cfg
Clean up Makefile, and drop a lot of the config.mk files on the way.

We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:12:04 +02:00
Wolfgang Denk
14d0a02a16 Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:07:10 +02:00
Michal Simek
d69f8f41af microblaze: Add support for NET_MULTI api
Microblaze hasn't supported NET_MULTI support.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2010-10-12 16:51:34 +10:00
Wolfgang Denk
500fbae204 Merge branch 'master' of git://git.denx.de/u-boot-microblaze 2010-04-24 21:13:31 +02:00
Stefan Roese
a47a12becf Move arch/ppc to arch/powerpc
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.

Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
2010-04-21 23:42:38 +02:00
Michal Simek
b26640971a microblaze: Move FSL initialization to board.c
Move FSL out of interrupt controller.

Signed-off-by: Michal Simek <monstr@monstr.eu>
2010-04-16 12:15:33 +02:00
Peter Tyser
6260fb0458 microblaze: Move cpu/microblaze/* to arch/microblaze/cpu/*
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:26 +02:00
Peter Tyser
8d1f268204 ppc: Move cpu/$CPU to arch/ppc/cpu/$CPU
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:16 +02:00
Peter Tyser
61f2b38a17 Replace "#include <asm-$ARCH/$FILE>" with "#include <asm/$FILE>"
The appropriate include/asm-$ARCH directory should already by symlinked
to include/asm so using the whole "asm-$ARCH" path is unnecessary.

This change should also allow us to move the include/asm-$ARCH
directories into their appropriate lib/$ARCH/ directories.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-04-13 09:13:04 +02:00
Wolfgang Denk
a574cff121 ml300: remove support for broken, orphaned board
The ml300 board has a number of issues, but nobody cares about this
long-orphaned board any more.  Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
2010-03-28 00:18:58 +01:00
Stefan Roese
b1245dd3c6 ppc4xx: Add custom linker script to board/*/config.mk
These boards have special linker scripts right now. We can't use the
common 4xx linker script here. So overrride the linker script (LDSCRIPT)
in board/*/config.mk and choose the board specific version.

Signed-off-by: Stefan Roese <sr@denx.de>
2009-11-02 16:29:04 +01:00
Peter Tyser
858290178f ppc: Enable full relocation to RAM
The following changes allow U-Boot to fully relocate from flash to
RAM:
 - Remove linker scripts' .fixup sections from the .text section
 - Add -mrelocatable to PLATFORM_RELFLAGS for all boards
 - Define CONFIG_RELOC_FIXUP_WORKS for all boards

Previously, U-Boot would partially relocate, but statically initialized
pointers needed to be manually relocated.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-10-03 10:15:45 +02:00
Michal Simek
aedb468309 microblaze: Add sbss, scommon and COMMON symbols for clearing
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-09-14 14:40:03 +02:00
Mike Frysinger
9aef738885 unify HOST_CFLAGS and HOSTCFLAGS
The top build system sets up HOSTCFLAGS a bit and exports it, but other
places use HOST_CFLAGS instead.  Unify the two as HOSTCFLAGS so that the
values stay in sync.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-23 21:26:14 +02:00
Trent Piepho
f62fb99941 Fix all linker script to handle all rodata sections
A recent gcc added a new unaligned rodata section called '.rodata.str1.1',
which needs to be added the the linker script.  Instead of just adding this
one section, we use a wildcard ".rodata*" to get all rodata linker section
gcc has now and might add in the future.

However, '*(.rodata*)' by itself will result in sub-optimal section
ordering.  The sections will be sorted by object file, which causes extra
padding between the unaligned rodata.str.1.1 of one object file and the
aligned rodata of the next object file.  This is easy to fix by using the
SORT_BY_ALIGNMENT command.

This patch has not be tested one most of the boards modified.  Some boards
have a linker script that looks something like this:

*(.text)
. = ALIGN(16);
*(.rodata)
*(.rodata.str1.4)
*(.eh_frame)

I change this to:

*(.text)
. = ALIGN(16);
*(.eh_frame)
*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))

This means the start of rodata will no longer be 16 bytes aligned.
However, the boundary between text and rodata/eh_frame is still aligned to
16 bytes, which is what I think the real purpose of the ALIGN call is.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
2009-03-20 22:39:12 +01:00
Mike Frysinger
b6b4625d17 boards: get mac address from environment
The boards that get converted here to use the environment for the mac
address rather than global data:
	debris
	mgcoge
	mgsuvd
	muas3001
	netstal
	pn62
	sixnet
	vcma9
	xilinx (the ones that use xilinx_enet)

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Sangmoon Kim <dogoil@etinsys.com>
CC: Heiko Schocher <hs@denx.de>
CC: David Mueller <d.mueller@elsoft.ch>
CC: Niklaus Giger <niklaus.giger@netstal.com>
CC: Wolfgang Grandegger <wg@denx.de>
CC: Dave Ellis <DGE@sixnetio.com>
CC: Ricardo Ribalda <ricardo.ribalda@uam.es>
2009-03-20 22:39:10 +01:00
Michal Simek
330e55459b microblaze: Change microblaze-generic config file
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-01-23 10:39:59 +01:00
Michal Simek
52a822ed9c microblaze: Rename ml401 to microblaze-generic
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-01-23 10:39:56 +01:00
Jean-Christophe PLAGNIOL-VILLARD
3aed3aa2c1 Fix new found CFG_
Also fix some minor typos.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-14 10:55:30 +01:00
Michal Simek
8fab49ea91 microblaze: Remove XUPV2P board
---

Microblaze platforms use generic settings and to have
many platforms is confusing that's why I decided to remove this
platform from U-BOOT. ml401 tree is sufficient for covering
all Microblaze platforms.

This change will go through microblaze custodian tree.
2008-12-10 09:25:33 +01:00
Michal Simek
89295028e7 ppc4xx: ml300 remove Xilinx BSP from ml300 folder
This BSP should be outside u-boot source tree.
The second reason is that xilinx ppc405 was moved to generic platform.

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-11-25 09:06:57 +01:00
Selvamuthukumar
9b827cf172 Align end of bss by 4 bytes
Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.

Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-11-18 23:13:16 +01:00
Ben Warren
4d03a4e20e Moved PPC4xx EMAC driver to drivers/net
Also changed path in all linker scripts that reference this driver

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
2008-11-09 21:38:04 -08:00
Ricardo Ribalda Delgado
1f4d53260e ppc4xx: Generic architecture for xilinx ppc405(v3)
As "ppc44x: Unification of virtex5 pp440 boards" did for the xilinx
ppc440 boards, this patch presents a common architecture for all the
xilinx ppc405 boards.

Any custom xilinx ppc405 board can be added very easily with no code
duplicity.

This patch also adds a simple generic board, that can be used on almost
any design with xilinx ppc405 replacing the file ppc405-generic/xparameters.h

This patch is prepared to work with the latest version of EDK (10.1)

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-10-24 17:26:09 +02:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Wolfgang Denk
afbc526336 Merge branch 'Makefile-next' of git://git.denx.de/u-boot-arm 2008-09-12 16:13:12 +02:00
Ricardo Ribalda Delgado
61737c59a3 ppc4xx: Add .gitignore file to xilinx-ppc440 boards
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-12 07:11:48 +02:00
Ricardo Ribalda Delgado
4bed9deebb ppc4xx: Fix in-tree build for ppc440-generic boards
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-12 07:08:08 +02:00
Jean-Christophe PLAGNIOL-VILLARD
0e8d158664 rename CFG_ENV macros to CONFIG_ENV
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:06 +02:00
Jean-Christophe PLAGNIOL-VILLARD
0cf4fd3cf8 rename environment.c in env_embedded.c to reflect is functionality
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:01 +02:00
Jean-Christophe PLAGNIOL-VILLARD
93f6d72544 rename CFG_ENV_IS_NOWHERE in CONFIG_ENV_IS_NOWHERE
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:00 +02:00
Jean-Christophe PLAGNIOL-VILLARD
bb1f8b4f8b rename CFG_ENV_IS_IN_EEPROM in CONFIG_ENV_IS_IN_EEPROM
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 21:09:38 +02:00
Ricardo Ribalda Delgado
880f6a5d75 ppc4xx: ppc440-generic-ALL: Fix out of tree build v2
This patch solves the problems compiling ml507, v5fx30teval and
ppc440-generic out of tree.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
2008-09-09 16:08:05 +02:00
Ricardo Ribalda Delgado
e07f4a8033 ppc44x: Unification of virtex5 pp440 boards
This patch provides an unificated way of handling xilinx v5 ppc440 boards.

It unificates 3 different things:

1) Source code
A new board called ppc440-generic has been created. This board includes
a generic tlb initialization (Maps the whole memory into virtual) and
defines board_pre_init, checkboard, initdram and get_sys_info weakly,
so, they can be replaced by specific functions.

If a new board needs to redefine any of the previous functions
(specific initialization) it can create a new directory with the
specific initializations needed. (see the example ml507 board).

2) Configuration file
Common configurations are located under configs/xilinx-ppc440.h, this
header file interpretes the xparameters file generated by EDK and
configurates u-boot in correspondence. Example: if there is a Temac,
allows CMD_CONFIG_NET
Specific configuration are located under specific configuration file.
(see the example ml507 board)

3) Makefile
Some work has been done in order to not duplicate work in the Main
Makefile. Please see the attached code.

In order to support new boards they can be implemented in the next way:

a) Simple Generic Board  (90% of the time)
Using EDK generates a new xparameters.h file, replace
ppc440-generic/xparameters.h  and run make xilinx-ppc440-generic_config
&& make

b) Simple Boards with special u-boot parameters (9 % of the time)
Create a new file under configs for it (use ml507.h as example) and
change your paramaters. Create a new Makefile paragraph and compile

c) Complex boards (1% of the time)
Create a new folder for the board, like the ml507

Finally, it adds support for the Avnet FX30T Evaluation board, following
the new generic structure:

Cheap board by Avnet for evaluating the Virtex5 FX technology.

This patch adds support for:
 - UartLite
 - 16MB Flash
 - 64MB RAM

Prior using U-boot in this board, read carefully the ERRATA by Avnet
to solve some memory initialization issues.

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-09-05 11:51:22 +02:00
Ricardo Ribalda Delgado
9246f5ecfd ppc4xx: ML507: Environment in flash and MTD Support
- Relocate the location of U-Boot in the flash
- Save the environment in one sector of the flash memory
- MTD Support

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-30 13:56:19 +02:00
Ricardo Ribalda Delgado
a8a16af4d5 ppc4xx: ML507: Use of get_ram_size in board ml507
- Change suggested by WD

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-30 11:36:51 +02:00
Ricardo Ribalda Delgado
01a004313c ppc4xx: ML507: U-Boot in flash and System ACE
This patch allows booting from FLASH the ML507 board by Xilinx.
Previously, U-Boot needed to be loaded from JTAG or a Sytem ACE CF

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-07-30 11:31:37 +02:00
Ricardo Ribalda Delgado
086511fc96 ppc4xx: ML507 Board Support
The Xilinx ML507 Board is a Virtex 5 prototyping board that includes,
	among others:
	-Virtex 5 FX FPGA (With a ppc440x5 in it)
	-256MB of SDRAM2
	-32MB of Flash
	-I2C Eeprom
	-System ACE chip
	-Serial ATA connectors
	-RS232 Level Conversors
	-Ethernet Transceiver

This patch gives support to a standard design produced by EDK for this
board: ppc440, uartlite, xilinx_int and flash

- Includes Changes propossed by Stefan Roese and Michal Simek

Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: Stefan Roese <sr@denx.de>
2008-07-18 12:31:17 +02:00
Wolfgang Denk
4ff170a818 Cleanup: fix "expected specifier-qualifier-list before 'phys_size_t'" errors
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-03 22:34:08 +02:00
Wolfgang Denk
c8a3b109f0 Cleanup out-or-tree building for some boards (.depend)
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-02 23:49:18 +02:00
Becky Bruce
9973e3c614 Change initdram() return type to phys_size_t
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory.  phys_size_t is defined as an unsigned long on almost
all current platforms.

This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram).  It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.

Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-12 08:50:18 +02:00
Stefan Roese
bbeff30cbd ppc4xx: Remove superfluous dram_init() call or replace it by initdram()
Historically the 405 U-Boot port had a dram_init() call in early init
stage. This function was still called from start.S and most of the time
coded in assembler. This is not needed anymore (since a long time) and
boards should implement the common initdram() function in C instead.

This patch now removed the dram_init() call from start.S and removes the
empty implementations that are scattered through most of the 405 board
ports. Some older board ports really implement this dram_init() though.
These are:

csb272
csb472
ERIC
EXBITGEN
W7OLMC
W7OLMG

I changed those boards to call this assembler dram_init() function now
from their board specific initdram() instead. This *should* work, but please
test again on those platforms. And it is perhaps a good idea that those
boards use some common 405 SDRAM initialization code from cpu/ppc4xx at
some time. So further patches welcome here.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:19 +02:00
Wolfgang Denk
53677ef18e Big white-space cleanup.
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-21 00:14:08 +02:00
Jason Wessel
3d36be0300 Remove all the search paths from the .lds files.
The cross compiler is responsible for providing the correct libraries
and the logic to find the linking libraries.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
2008-04-17 23:57:32 -07:00
Michal Simek
af7ae1a411 microblaze: clean uart16550 and uartlite handling
Signed-off-by: Michal Simek <monstr@monstr.eu>
2008-04-08 15:38:14 +02:00
Michal Simek
6bf3e982ae microblaze: remove old setting for emac driver
Signed-off-by: Michal Simek <monstr@monstr.eu>
2008-04-08 15:38:14 +02:00
Michal Simek
cd2b75efb9 microblaze: Clean Makefile from ancient emac driver
Signed-off-by: Michal Simek <monstr@monstr.eu>
2008-04-08 15:38:14 +02:00
Wolfgang Denk
64134f0112 Fix linker scripts: add NOLOAD atribute to .bss/.sbss sections
With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]

For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.

The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12 20:31:39 +01:00
Stefan Roese
882ae41274 ppc4xx: Rework of 4xx serial driver (2)
Change all linker scripts to reference the changed driver name 4xx_uart.o.

Note: In most cased all these explicit referencing of these object files
in the linker scripts is not neccessary. Only for manually embedded
environment into the U-Boot image, which is not done is most cases.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:51 +01:00
Stefan Roese
087dfdb79b ppc4xx: Consolidate some of the 405 and 440 macros/structs into 4xx
This patch moves some common 4xx macros and the PPC405_SYS_INFO/
PPC440_SYS_INFO structure into the common ppc4xx.h header.

Lot's of other macros are good candidates to be consolidated this way
in the future.

Signed-off-by: Stefan Roese <sr@denx.de>
2007-10-31 21:20:50 +01:00
Michal Simek
991b089d1c Synchronize with U-BOOT mainline 2007-09-15 00:03:35 +02:00
Michal Simek
85fad497b3 Merge git://www.denx.de/git/u-boot 2007-08-07 22:12:05 +02:00
Michal Simek
98889edd50 [FIX] Change configuration for XUPV2P Microblaze board 2007-08-05 15:54:53 +02:00
Jon Loeliger
d39b574158 board/[j-z]*: Remove lingering references to CFG_CMD_* symbols.
Fixed some broken instances of "#ifdef CMD_CFG_IDE" too.
Those always evaluated TRUE, and thus were always compiled
even when IDE really wasn't defined/wanted.

Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-07-10 10:48:22 -05:00
Jon Loeliger
ab3abcbabd board/[q-z]*: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-07-09 18:48:11 -05:00
Wolfgang Denk
52b8704d02 Fix a few file permission problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-07-04 00:43:53 +02:00
Jon Loeliger
9107ebe0d3 board/[k-z]*: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.

All transformations are of the form:
Before:
    #if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
    #if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)

Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-07-04 00:35:03 +02:00
Michal Simek
3666afffe7 [FIX] fix microblaze file permitission 2007-06-17 19:03:21 +02:00
Michal Simek
3c4bd60de1 Merge git://www.denx.de/git/u-boot
Conflicts:

	include/asm-microblaze/microblaze_intc.h
	include/linux/stat.h
2007-05-08 00:32:35 +02:00
Michal Simek
fb05f6da35 new: USE_MSR_INTR support 2007-05-07 23:58:31 +02:00
Michal Simek
19bf1fbad7 new: fsl interrupt support
FSL_Has_data is connected to INTC.
2007-05-07 19:33:51 +02:00
Michal Simek
48fbd3a4cd new: add writing to msr register 2007-05-07 17:11:09 +02:00
Michal Simek
ffc50f9bb1 new: FSL and MSR support #2 2007-05-05 18:54:42 +02:00
Michal Simek
9d1d6a34d2 Change ML401 parameters - Xilinx BSP 2007-04-21 20:53:31 +02:00
Wolfgang Denk
31c98a8822 Minor coding style cleanup. 2007-04-04 02:09:30 +02:00
Michal Simek
342cd097be [PATCH] Clean include dependence 2007-03-30 22:52:09 +02:00
Michal Simek
5da048adf4 PATCH: Resolve GPL license problem 2007-03-27 00:32:16 +02:00
Michal Simek
1798049522 Support for XUPV2P board
Reset support
BSP autoconfig support
2007-03-26 01:39:07 +02:00
Michal Simek
cfc67116a7 [Microblaze][PATCH] part 2
timer support
interrupt controller support
flash support
ethernet support
cache support
board information support
env support
booting image support

adding support for Xilinx ML401
2007-03-11 13:48:24 +01:00
Michal Simek
76316a318d [Microblaze][PATCH]
timer support
interrupt controller support
flash support
ethernet support
cache support
board information support
env support
booting image support

adding support for Xilinx ML401
2007-03-11 13:42:58 +01:00
Grant Likely
99b0f0fd3f [PATCH 2_4] Use config.h, not xparameters.h, for xilinx targets
Change the xilinx device drivers and board code to include config.h
instead of xparameters.h directly.  config.h always includes the
correct xparameters file.  This change reduces the posibility of
including the wrong file when adding a new xilinx board port

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2007-02-20 09:04:52 +01:00
Wolfgang Denk
2b208f5308 Move "ar" flags to config.mk to allow for silent "make -s"
Based on patch by Mike Frysinger, 20 Jun 2006
2006-10-09 01:02:05 +02:00
Marian Balakowicz
f93286397e Add support for a saving build objects in a separate directory.
Modifications are based on the linux kernel approach and
support two use cases:

  1) Add O= to the make command line
  'make O=/tmp/build all'

  2) Set environement variable BUILD_DIR to point to the desired location
  'export BUILD_DIR=/tmp/build'
  'make'

The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'

Command line 'O=' setting overrides BUILD_DIR environent variable.

When none of the above methods is used the local build is performed and
the object files are placed in the source directory.
2006-09-01 19:49:50 +02:00
Wolfgang Denk
d87080b721 GCC-4.x fixes: clean up global data pointer initialization for all boards. 2006-03-31 18:32:53 +02:00
Wolfgang Denk
763b5f34c3 Remove board specific configuration includes from the common xilinx
ethernet and iic adapter code.
Patch by Michael Libeskind, 12 Jul 2005
2006-03-12 23:13:27 +01:00
Stefan Roese
18c5e64c5b Fix various compiler warnings on ppc4xx builds (ELDK 4.0)
Patch by Stefan Roese, 18 Jan 2006
2006-01-18 20:06:44 +01:00
Wolfgang Denk
7481266e4e 2005-12-12 16:06:05 +01:00
Wolfgang Denk
77ddac9480 Cleanup for GCC-4.x 2005-10-13 16:45:02 +02:00
Wolfgang Denk
807d5d7319 Fix problems with ld version 2.16 (dot outside sections problem)
Pointed out by Gerhard Jaeger, 31 Aug 2005;
cf. http://sourceware.org/ml/binutils/2005-08/msg00412.html
2005-08-31 12:28:00 +02:00
Stefan Roese
d6c61aabc4 Merged 405gp_enet.c and 440gx_enet.c to generic 4xx_enet.c
now handling all 4xx cpu's.
Patch by Stefan Roese, 16 Aug 2005
2005-08-16 18:18:00 +02:00
wdenk
a1191902ca * Patch by Jon Loeliger, 02 Sep 2004:
Reset monitor size back to 256 so environment can be written
  to flash on MPC85xx ADS and CDS releases.

* Patch by Paolo Broggini, 02 Sep 2004:
  Make BSS clearing on ARM systems more robust

* Patch by Yue Hu and Joe, 01 Sep 2004:
  - add PCI support for ixp425;
  - add EEPRO100 suppor tfor ixdp425 board.

* Fix problem with protected sector detection in driver/cfi_flash.c
2005-01-09 17:12:27 +00:00
wdenk
e2ffd59b4d * Code cleanup, mostly for GCC-3.3.x
* Cleanup confusing use of CONFIG_ETH*ADDR - ust his only to
  pre-define a MAC address; use CONFIG_HAS_ETH* to enable support for
  additional ethernet addresses.

* Cleanup drivers/i82365.c - avoid duplication of code

* Fix bogus "cannot span across banks" flash error message

* Add support for CompactFlash for the CPC45 Board.
2004-12-31 09:32:47 +00:00
wdenk
a06752e36b * Patch by Sean Chang, 9 Aug 2004:
- Added I2C support for ML300.
  - Added support for ML300 to read out its environment information
    stored on the EEPROM.
  - Added support to use board specific parameters as part of
    U-Boot's environment information.
  - Updated MLD files to support configuration for new features
    above.

* Patches by Travis Sawyer, 5 Aug 2004:
  - Remove incorrect bridge settings for eth group 6
  - Add call to setup bridge in ppc_440x_eth_initialize
  - Fix ppc_440x_eth_init to reset the phy only if its the
    first time through, otherwise, just check the phy for the
    autonegotiated speed/duplex.  This allows the use of netconsole
  - only print the speed/duplex the first time the phy is reset.
2004-09-29 22:43:59 +00:00
wdenk
028ab6b598 * Patch by Peter Ryser, 20 Feb 2004:
Add support for the Xilinx ML300 platform

* Patch by Stephan Linz, 17 Feb 2004:
  Fix watchdog support for NIOS

* Patch by Josh Fryman, 16 Feb 2004:
  Fix byte-swapping for cfi_flash.c for different bus widths

* Patch by Jon Diekema, 14 Jeb 2004:
  Remove duplicate "FPGA Support" notes from the README file
2004-02-23 23:54:43 +00:00