For all sandbox systems with DM_RNG we enable RNG_SANDBOX. So we can simply
set the default to yes.
All rng drivers depend on DM_RNG. Use a single 'if' instead of individual
dependencies. Now 'make menuconfig' shows the individual drivers neatly
indented under the DM_RNG entry.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Currently when booting the kernel on i.MX8 U-Boot hangs in an
endless loop when switching off dma, connectivity or lsio power
domains during device removal. It hapens first when removing
gpio0 (gpio@5d080000) device, here its power domain device
'lsio_gpio0' is obtained for switching off power. Since the
obtained 'lsio_gpio0' device is removed afterwards, its power
domain is also switched off and here the parent power domain
device 'lsio_power_domain' is optained for switching off the
power. Thereafter, when the obtained 'lsio_power_domain' is
removed, device_remove() removes its first child 'lsio_gpio0'.
During this child removal the 'lsio_power_domain' device is
obtained again for switching and when removing it later,
the same child removal is repeated, so we are stuck in an
endless loop. Below is a snippet from dm tree on i.MX8QXP
for better illustration of the DM devices relationship:
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
...
simple_bus 0 [ + ] generic_simple_bus |-- imx8qx-pm
power_doma 0 [ + ] imx8_power_domain | |-- lsio_power_domain
power_doma 1 [ + ] imx8_power_domain | | |-- lsio_gpio0
power_doma 2 [ + ] imx8_power_domain | | |-- lsio_gpio1
Do not remove a power domain device if it is a parent of the
currently controlled device.
Fixes: 52edfed65d ("dm: core: device: switch off power domain after device removal")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Oliver Graute <oliver.graute@gmail.com>
Reported-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
The PHY models of the Marvell 88E151x series are not reliably
distinguishable by their uid / PHY identifiers.
The 88E1510, 88E1512, 88E1514 and 88E1518 all have the same OUI and
model number and bits 3:0 in the PHY Identifier 2 (Page 0, Reg 3) are
described as HW revision number, but both 88E1510 and 88E1518 PHYs were
observed with the same HW rev number (1).
Before commit 83cfbeb0df ("net: phy: Fix mask so that we can identify
Marvell 88E1518"), the 88E151x were detected because the HW revision
bits were masked from the uid. After that change, 88E1510/12/18 were all
detected as 88E1518 and the 88E1510 specific code was no longer run.
I modified the mask to again ignore all four HW revision bits, removed
the 88E1510 specific code (board-specific LED/INTn setup), which was not
called since late 2016 anyway and renamed the config function and
phy_driver struct to the better fitting 88e151x.
The uid and mask bits 3:0 are now again the same as in the Linux kernel.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
This patch adds ability to switch beetween two PHY SGMII modes.
Some hardware, for example, FPGA IP designs may use 6-wire mode
which enables differential SGMII clock to MAC.
Patch description, dt flags have been done in mainline Linux by
commit a2111c460c0c ("net: phy: dp83867: Add documentation for SGMII mode type")
and by commit 507ddd5c0d47 ("net: phy: dp83867: Add SGMII mode type switching")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 27c3f70f3b ("net: phy: Increase link up delay in
genphy_update_link()") increased the per-iteration waiting time from
1ms to 50ms, without adjusting the timeout counter. This lead to the
timeout increasing from the typical 4 seconds to over three minutes.
Adjust the timeout counter evaluation by that factor of 50 to bring the
timeout back to the intended value.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fixes: net: phy: Increase link up delay in genphy_update_link() ("27c3f70f3b50")
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The driver now unconditionally prints some information that's not
universally useful. Replace printf with debug.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use either USXGMII or XFI in aquantia_set_proto and drop XGMII as a valid
protocol configuration. The PHY doesn't support it, it's just used as an
alias for one of the other two protocols.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add NC-SI to the usual phy handling. This makes two notable changes:
- Somewhat similar to a fixed phy, phy_connect() will create an NC-SI
phy if CONFIG_PHY_NCSI is defined.
- An early return is added to phy_read() and phy_write() to handle a
case like the NC-SI phy which does not define a bus.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.
NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).
This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).
The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.
[0]: https://github.com/torvalds/linux/tree/master/net/ncsi
[1]: https://github.com/torvalds/linux/blob/master/net/ncsi/ncsi-pkt.h
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some device may enable CONFIG_CLK but not still support this clock in
CC, so better use debug() in place of dev_warn() otherwise a lot of
boards will throw useless dev_warn()s.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 4 bit MMC controllers have an internal debounce for the SDCD line
with a debounce delay of 1 second. Therefore, after clocks to the IP are
enabled, software has to wait for this time before it can power on the
controller.
Add a deferred_probe() callback which polls on sdcd for a maximum of 2 seconds
before switching on power to the controller or (in the case of no card)
returning a ENOMEDIUM. This pushes the 1 second wait time to when the
card is actually needed rather than at every probe() making sure that
users who don't insert an SD card in the slot don't have to wait such a
long time.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
With the latest RIOT, there is a different otap delay value for each
speed mode. Add a new binding with every supported speed mode. Also
disable a given speed mode in the host caps if its corresponding
otap-del-sel is not present.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
MMC_LEGACY & SD_LEGACY are not differentiated timings in the spec and
don't have any meaningful differences. Therefore, get rid of all
references to SD_LEGACY and use MMC_LEGACY to mean both of them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add the sdhci_deferred_probe() function to register as the
deferred_probe() callback to the mmc core. It will in turn call the
deferred_probe() callback of the platform drivers as declared in the
sdhci_ops.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add a deferred_probe() API for platforms that want to do some
configurations just before starting to enumerate the device.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Initial DesignWare based DM support for Cortina Access CAxxxx SoCs.
Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Currently the ofdata_to_platdata() method calls dev_read_addr_pci(),
which potentially accesses the parent PCI bus. If this happens before
the parent PCI bus is probed the resulting address will be wrong.
This behavior was triggered by commit 82de42fa14 ("dm: core:
Allocate parent data separate from probing parent").
According to a comment in drivers/pci/pci-uclass.c [1] accessing
the PCI parent bus in ofdata_to_platdata() is not allowed, and the
access should be moved to the probe() function.
Move the call to dev_read_addr_pci() and the related handling of the
'addr' value from the ofdata_to_platdata() to its own function,
which is then called from the probe() method.
While moving the code, the comment /* try Processor Local Bus device
first */ was dropped. It was initially added with commit 3db886a5bf
("serial: ns16550: Support ns16550 compatible pci uart devices") and
later made obsolete with commit 33c215af4b ("dm: pci: Add a function
to read a PCI BAR").
[1] Comment in drivers/pci/pci-uclass.c:
"A common cause of this problem is that this function is called in the
ofdata_to_platdata() method of @dev. Accessing the PCI bus in that
method is not allowed, since it has not yet been probed. To fix this,
move that access to the probe() method of @dev instead."
Fixes: 82de42fa14 ("dm: core: Allocate parent data separate from probing parent")
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com> # Tested on Intel Galileo
If all branches of a switch statement have a return instruction, all
subsequent lines are unreachable.
Identified with cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When flow id is not marked as valid, sysfw reads the register value to
get the range of flow ids that are supported. Then compares the flow range
with the U-Boot's host id. This will definitely fail as board
configuration doesn't assign the full range to U-Boot's host id. In order
to work around this, mark the flow id as valid and pass range as 0.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
SYSFW v2020.01 and later versions no longer supports the below messages:
- TI_SCI_MSG_RM_RING_GET_CFG
- TISCI_MSG_RM_UDMAP_TX_CH_GET_CFG 0x1206
- TISCI_MSG_RM_UDMAP_RX_CH_GET_CFG 0x1216
- TISCI_MSG_RM_UDMAP_FLOW_GET_CFG 0x1232
- TISCI_MSG_RM_UDMAP_FLOW_SIZE_THRESH_GET_CFG 0x1233
There are no users in U-Boot for any of the above messages, So drop the
support for all the corresponding messages.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Fix the macro to set the pplmsb field (bit 3) of the RASTER_TIMING_0
register. It is used in order to support up to 2048 pixels per line.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Update the driver to support the device tree and the driver model.
Timings and panel parameters are now loaded from the device tree.
The DM code replaces the am335x_lcdpanel structure with
tilcdc_panel_info taken from the linux kernel, as well the management
of additional parameters not covered in the legacy code. In addition,
the am335x_lcdpanel structure contains parameters and operations that
were probably a requirement of the board for which this driver was
developed and which, however, were not developed in the linux kernel.
All this led to rewrite th DM controller initialization code, except
for the pixel clock setting that is executed in a function created in a
previous patch with code taken from the legacy am335xfb_init.
The patch has been tested on a custom board with u-boot 2018.11-rc2 and
the following device-tree configuration:
panel {
compatible = "ti,tilcdc,panel";
pinctrl-names = "default";
pinctrl-0 = <&lcd_enable_pins>;
enable-gpios = <&gpio0 31 0>;
backlight = <&backlight>;
status = "okay";
u-boot,dm-pre-reloc;
panel-info {
ac-bias = <255>;
ac-bias-intrpt = <0>;
dma-burst-sz = <16>;
bpp = <16>;
fdd = <0x80>;
sync-edge = <0>;
sync-ctrl = <1>;
raster-order = <0>;
fifo-th = <0>;
};
display-timings {
native-mode = <&timing0>;
timing0: 800x480 {
hactive = <800>;
vactive = <480>;
hback-porch = <46>;
hfront-porch = <210>;
hsync-len = <20>;
vback-porch = <23>;
vfront-porch = <22>;
vsync-len = <10>;
clock-frequency = <33000000>;
hsync-active = <0>;
vsync-active = <0>;
};
};
};
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
Created in preparation to support driver-model, they can also be called
from legacy code. In this way, code duplication is avoided.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
In case of null error, round rate is equal to target rate, so it is
useless to continue to search the DPLL setup parameters to get the
desidered pixel clock rate.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The latest data manual SPRSP08I –NOVEMBER 2017–REVISED DECEMBER 2019[1]
for am65xx SoC states the new MPU nominal voltages to be 1.1V (OPP_NOM),
1.2V (OPP_OD) and 1.24V (OPP_TURBO). Update the nominal voltages in the
K3 AVS driver to reflect this.
[1] http://www.ti.com/lit/gpn/am6528
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The ESM (Error Signal Monitor) is used on certain PMIC versions to
handle error signals propagating from rest of the system. If these
reach the PMIC, it is typically a last resort fatal error which
requires a system reset. The ESM driver does the proper configuration
for the ESM module to reach this end goal. Initially, only TPS65941
PMIC is supported for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The ESM (Error Signaling Module) is used to route error signals within
the K3 SoCs somewhat similar to interrupts. The handling for these is
different though, and can be routed for hardware error handling, to
be handled by safety processor or just as error interrupts handled
by the main processor. The u-boot level ESM driver is just used to
configure the ESM signals so that they get routed to proper destination.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
TPS65941 can have child devices under it (like the ESM support), so
probe these once the master pmic node completes probe.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Descend to drivers/soc directory unconditionally for SPL and U-Boot
builds. Individual drivers can have their own config to check what needs
to be built for SPL. There should be no increase in SPL code size
due to this change.
This is required on K3 SoCs to support DMA in SPL.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add driver flag to skip power domain disabling on device removal.
Fixes: 52edfed65d ("dm: core: device: switch off power domain after device removal")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
In various cases a power domain must stay enabled after device
removal when booting OS (i.e. serial debug console or display).
Add a flag to selectively skip switching off a power domain.
Fixes: 52edfed65d ("dm: core: device: switch off power domain after device removal")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We should not assign a value that is overwritten before use.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This adds a compatible string for m41st87. This ensures that this driver
can be used for m41st87.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
After the commit 9b643e312d ("treewide: replace with error()
with pr_err()"), there are pr_err() usages without line break. Add
missing line breaks for pr_err() used in f_thor.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
In case dfu command is being executed with timeout option,
the timer may expire in the middle of DFU operation. If there
is DFU request coming, we may simple reset timeout value
to prevent aborting of ongoing DFU operation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
Commit 06985289d4 ("watchdog: Implement generic watchdog_reset()
version") introduced an automatic selection of CONFIG_WATCHDOG by
CONFIG_WDT. But for boards selecting CONFIG_HW_WATCHDOG, like
boards have a powerpc 8xx, CONFIG_WATCHDOG shall not be selected
as they are mutually exclusive.
Make CONFIG_WATCHDOG dependent on !CONFIG_HW_WATCHDOG
Fixes: 06985289d4 ("watchdog: Implement generic watchdog_reset() version")
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit f3729ba6e7 ("watchdog: mpc8xx_wdt: Watchdog driver and macros
cleanup") switched the watchdog to CONFIG_WATCHDOG. But this is not
compatible with the 8xx because it starts the watchdog HW timer at
reset and must be serviced from the very beginning including while
U-boot is executed in the firmware before relocation in RAM.
Select CONFIG_HW_WATCHDOG and make hw_watchdog_reset() visible.
Meanwhile, finalise the cleanup of arch/powerpc/cpu/mpc8xx/Kconfig by
removing the lines put in comment in that commit, and also remove
again the selection of CONFIG_MPC8xx_WATCHDOG which was removed by
that commit and brought back by mistake by commit b3134ffbd9
("watchdog: Kconfig: Sort entry alphabetically")
Note that there was an 'imply WATCHDOG' in the original commit but
it disappeared in the Kconfig alphabetical sorting, so no need to
remove it here.
Fixes: f3729ba6e7 ("watchdog: mpc8xx_wdt: Watchdog driver and macros cleanup")
Fixes: b3134ffbd9 ("watchdog: Kconfig: Sort entry alphabetically")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Stefan Roese <sr@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Driver probe function is called again and again in case of error.
Malloc space is getting full which is is reported by:
Insufficient RAM for page table: 0x15000 > 0x14000.
Please increase the size in get_page_table_size()
### ERROR ### Please RESET the board ###
The patch is freeing allocated buffers on error path to avoid panic.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On Xilinx ZynqMP revA board initial value of PHYCR register is 0x5448 which
means FORCE_LINK_GOOD is already setup. Origin code was doing write but the
new code is doing read/modify/write and keep this bit untouched. That's why
ethernet stop to work.
The patch is cleaning this bit when PHYCR value is composed.
Tested on Xilinx zcu102-revA and zcu104-rev1.0 boards.
Fixes: 37d6265f2b ("net: phy: dp83867: refactor rgmii configuration")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Fixed wrong enumeration of nand_config structure. Added chip select
function before reading the nand chip for maf/dev id's, without this
unable to access id's from some of the micron chips. Also added a
print statement to identify if a nand flash is using on-die ecc.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The clock driver makes EEMI call to get the name of invalid clk
when executing versal_get_clock_info() function. This results in
error messages.
Added check for validating clock before saving clock attribute and
calling versal_pm_clock_get_name() in versal_get_clock_info() function.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
flush_dcache_range() expects unsigned long in the arguments. Here u32
variable is unable to hold the higher address value when ddr mapped
to higher addresses & flushing lower address dchache range instead
which is unmapped causing to crash.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Its possible that k3_avs_priv is NULL because the driver may not have
been probed yet. Therefore check if pointer is valid before
dereferencing it.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This reverts commit 1ee4942918.
Commit 1ee4942918 ("ata: fsl_ahci: Add sata DM support for Freescale
powerpc socs") introduced SCSI layer to call AHCI private API in order
to support sata operations, In DM mode, This is not necessary for
non-AHCI sata. So revert it and have already updated the driver itself
to operate sata directly.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This driver currently performs cache operation before the DMA start,
but does nothing after the DMA completion.
When reading data by DMA, the cache invalidation is needed also after
finishing the DMA transfer. Otherwise, the CPU might read data from
the cache instead of from the main memory when speculative memory read
or memory prefetch occurs.
Instead of calling the cache operation directly, this commit adds
dma_unmap_single(), which performs cache invalidation internally,
but drivers do not need which operation is being run.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, sdhci_prepare_dma() calls flush_cache() regardless of the
DMA direction.
Actually, cache invalidation is enough when reading data from the device.
This is correctly handled by dma_map_single(), which mimics the DMA-API
in Linux kernel. Drivers can be agnostic which cache operation occurs
behind the scene.
This commit also sanitizes the difference between the virtual address
and the dma address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
host->mmc is already (struct mmc *).
memalign() returns an opaque pointer, so there is no need for casting.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use {lower,upper}_32_bits() instead of the combination of cast
and shift.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The same code is run for both SDHCI_QUIRK_32BIT_DMA_ADDR and
define(CONFIG_FIXED_SDHCI_ALIGNED_BUFFER).
Unify the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Using the global variable does not look nice.
Add a new field sthci::align_buffer to point to the bounce buffer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The reference manuals for MPC8308 and MPC8309 both say that the
esdhcctl aka DMA Control Register "is implemented as SDHCCR" in the
System configuration registers. Unfortunately, that doesn't mean that
the registers are just mirrors of each other - any write to esdhcctl
is simply ignored. So to actually enable cache snooping, we
unfortunately have to add a little ifdeffery.
There is, naturally, no description of the bit fields of esdhcctl in
the MPC8309 manual, but comparing the description of esdhcctl from the
LS1021A reference manual to the description of the sdhccr in MPC8309,
one also finds that the fields are bit-reversed, so the bit to set is
0x02000000 rather than 0x00000040 - this is also what board_mmc_init()
uses in the two gdsys/mpc8308/ boards.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
Unfortunately a recent change adjusted the order of the checks here such
that 400MHz now shows up as fast-plus speed (1Mbps). Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: d96440d1e3 ("i2c: designware_i2c: Add support for fast-plus speed")
These functions are defined before the callers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since commit 01298da31d ("mmc: Change mode when switching to a boot
partition"), errors in mmc_select_mode_and_width() are ignored.
The return value should be checked.
Fixes: 01298da31d ("mmc: Change mode when switching to a boot partition")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cadence sent out an errata report to their customers of this IP.
This errata is not so severe, but the tune request should be sent
twice to avoid the potential issue.
Quote from the report:
Problem Summary
---------------
The IP6116 SD/eMMC PHY design has a timing issue on receive data path.
This issue may lead to an incorrect values of read/write pointers of
the synchronization FIFO. Such a situation can happen at the SDR104
and HS200 tuning procedure when the PHY is requested to change a phase
of sampling clock when moving to the next tuning iteration.
Workarounds
-----------
The following are valid workarounds to resolve the issue:
1. In eMMC mode, software sends tune request twice instead of once at
each iteration. This means that the clock phase is not changed on
the second request so there is no potential for clock instability.
2. In SD mode, software must not use the hardware tuning and instead
perform an almost identical procedure to eMMC, using the HRS34 Tune
Force register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
erase_grp_size is used, when MMC_WRITE is enabled.
- error: ‘struct mmc’ has no member named ‘erase_grp_size’
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
If the host has Broken R1B, use only R1 response type.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl5GcB0ACgkQ4rK92eCq
k3Wr9gf/dDPJi6UBhLDio/IVKDBddOEUN0Lwdr9W0upL+DrdvEOyNyMSEKuLccIE
UTd1NmNNwcvgDRaPvB5o3R7twWItTW0cYlmVkFSZ228aq6xdf/SElN2OUD6B9Gh+
8bi6oVLu41TNMYn4VYxsEftcT2megfH8s+SH/FlvR5ua1yCC1vyrytEQjPIbJAB2
sa90ewDyp5EYqGLdAk6AVjPLeNZsaleGwuyLf04PoC2xhn+3HTEKJCJN4O46aJUr
0GUI7YN7pTjIfZdYfFqjcwoQV1xV2HtbjCTcOb8Td8TEYjIoILF8tSyfIwDXWGB5
zMQIQxUdQyNiqdBPFcnkAufjk+zLIQ==
=0dG+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200214' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
Solve type issue in stm32mp1_lse_enable and stm32mp1_clktree.
This patch solves the warnings when compiling with W=1
on stm32mp1 board:
clk_stm32mp1.c: In function ‘stm32mp1_lse_enable’:
clk_stm32mp1.c:1238:15: warning: comparison of integer expressions
of different signedness: ‘u32’ {aka ‘unsigned int’} and ‘int’
[-Wsign-compare]
clk_stm32mp1.c:1239:13: warning: comparison of integer expressions
of different signedness: ‘u32’ {aka ‘unsigned int’} and ‘int’
[-Wsign-compare]
clk_stm32mp1.c: In function ‘stm32mp1_clktree’:
clk_stm32mp1.c:1814:17: warning: comparison of integer expressions
of different signedness: ‘int’ and ‘unsigned int’
[-Wsign-compare]
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use int as result of dm_i2c_reg_read to avoid warning with
W=1 (warning: comparison is always false due to limited range
of data type [-Wtype-limits])
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
There is no reason to show RAM_ROCKCHIP_DEBUG entry in other .config files
as I see it for Xilinx ZynqMP.
\# CONFIG_U_QE is not set
\# CONFIG_RAM is not set
CONFIG_RAM_ROCKCHIP_DEBUG=y
Add missing dependency on RAM_ROCKCHIP driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
HDMI PLL has its own xtal with 27 MHz output but we treat it the same
way as other PLLs with 33.33 MHz input.
Fix that.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
The commit e8e9715df2 ("regulator: fixed: Modify enable-active-high behavior")
fixed the regulator driver behavior when 'enable-active-high' is defined.
Unfortunately, this patch used dm_regulator_platdata()'s "boot_on" member
to set GPIOD_IS_OUT_ACTIVE flag and enable the regulator.
The issue here is that regulator_common_ofdata_to_platdata() is called
_before_ regulator_pre_probe() function in which the 'regulator-boot-on'
property is asserted.
As a result the GPIOD_IS_OUT_ACTIVE flag is not set and gpio_request_by_name()
called in the former function is not enabling the regulator.
This is problematic for e.g. i.MX ethernet driver, which then tries to
perform initialization without power (and fails).
The solution here is to explicitly enable regulator in regulator_pre_probe()
callback only when 'regulator-boot-on' property is present in device tree.
The GPIOD_IS_OUT_ACTIVE flag is not set at all, but relevant gpio is
requested.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
- Move P2SB from Apollo Lake to a more generic location
- Add a function to find a device by drvdata in DM core
- Enhancement of DM IRQ uclass driver
- Add a clock driver for Intel devices
- Add support for ACPI general-purpose events
- Add a TPM driver for H1/Cr50
- Enable TPM on Google Chromebook Coral
- fix vid_console_color() build warning
- fix for mxsfb to ensure correct Linux logo position
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXkGKMg4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCY3AJ9zzSWCPRa6M6YbYiHyfasyP1uf+gCdG2bMDRaC
vNpAeNnM9aWgJMkje6k=
=al8x
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix Coverity CID 280902 issue in vid_console_color()
- fix vid_console_color() build warning
- fix for mxsfb to ensure correct Linux logo position
Set the correct offset length and chip address offset mask for each
device to allow correct access to total capacity of the devices.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Since commit bcee8d6764 ("dm: gpio: Allow control of GPIO uclass in SPL")
CONFIG_DM_74X164 is no longer built for mx7dsabresd_defconfig, as
this target does not use CONFIG_SPL_GPIO.
Remove such dependency and let the the 74X164 GPIO driver be built
again.
This restores Ethernet functionality on the imx7-sdb board as the
Ethernet reset PHY comes from a GPIO driven by a 74LV595PW I/O
expander.
Fixes: bcee8d6764 ("dm: gpio: Allow control of GPIO uclass in SPL")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Alifer Moraes <alifer.wsdm@gmail.com>
Add serial UART driver support for all Cortina Access
CAxxxx family of SoCs.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Add support for hardware watchdog timer on all Cortina Access
CAxxxx family of SoCs.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
DM_GPIO based GPIO controller driver for CAxxxx SoCs.
This driver support multiple CPU architectures and
Cortina Access SoC platforms.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
building mtk ethernet driver for aarch64 (mt7622) results
in warnings/errors
"error: cast from pointer to integer of different size"
Fixes: 23f17164d9 ("ethernet: MediaTek: add ethernet driver for MediaTek ARM-based SoCs")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This patch add sgmii init part for the mediatek SoC that
support sgmii mode. It is a must for mt7622.
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
H1 is a Google security chip present in recent Chromebooks, Pixel phones
and other devices. Cr50 is the name of the software that runs on H1 in
Chromebooks.
This chip is used to handle TPM-like functionality and also has quite a
few additional features.
Add a driver for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present driver model supports the IRQ uclass but there is no way to
request a particular interrupt for a driver.
Add a mechanism, similar to clock and reset, to read the interrupts
required by a device from the device tree and to request those interrupts.
U-Boot itself does not have interrupt-driven handlers, so just provide a
means to read and clear an interrupt. This can be useful to handle
peripherals which must use an interrupt to determine when data is
available, for example.
Bring over the basic binding file as well, from Linux v5.4. Note that the
older binding is not supported in U-Boot; the newer 'special form' must be
used.
Add a simple test of the new functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add an IRQ type to each driver and use irq_first_device_type() to find
and probe the correct one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There can be different types of interrupt controllers in a system and some
drivers may need to distinguish between these. In general this can be
handled using the device tree by adding the interrupt information to
device nodes.
However on x86 devices we have interrupt controllers which are not tied
to any particular device and not really used in U-Boot. These still need
to be inited, so a convenient method is to give each controller a type
and allow a particular controller type to be probed.
Add support for this in sandbox along with a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove the new bland line at EOF of test/dm/irq.c]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
So far we have avoided adding a clock driver for Intel devices. But the
Designware I2C driver needs a different clock (133MHz) on Intel devices
than on others (166MHz). Add a simple driver that provides this
information.
This driver can be expanded later as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have uclass_first_device_drvdata(), use it from the I2C driver
to reduce code duplication.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have uclass_first_device_drvdata(), use it from syscon to
reduce code duplication.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is sometimes useful to find a device in a uclass using only its driver
data. The driver data often indicates the 'subtype' of the device, e,g,
via its compatible string.
Add a function to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This partially reverts changes by commit 2cc393f32f
("video: make BPP and ANSI configs optional") since it
caused issues with other boards (missing LCD console
output on pinebook, x86 platform or sandbox). Enable
all disabled options again and opt out of not supported
color depth in board defconfigs.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Now that we can use direct access to the system malloc() in sandbox, drop
the remaining uses of os_malloc().
The only one remaining now is for the RAM buffer, which we do want to be
at a known address, so this is intended.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most files don't need this header and it pulls in quite of lots of stuff,
malloc() in particular. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add a new device-tree property to control the colour depth. At present we
support 16bpp and 32bpp.
While we are here, update the code to use livetree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
On high-DPI displays U-Boot's LCD window can look very small. Add a
-K flag to expand it to make things easier to read, while still using
the existing resolution internally.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
At present an error does not stop the sound-output loop. This is incorrect
since nothing can be gained by trying to continue. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is no positive indication that U-Boot has finished
sending sound data. This means that it is not possible to power down an
audio codec, for example. Add a new method that is called once all sound
data has been sent.
Add a new method for this, called when the sound_play() call is done.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
For sandbox we want to have the maximum possible build coverage, so enable
all colour depths for video.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
At present only a 16bpp display is supported for Truetype fonts. Add
support for 32bpp also since this is quite common.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This adds a subcommand to dm to dump out what drivers are installed, and their
compatible strings. I have found this useful in ensuring that I have the correct
drivers compiled, and that I have put in the correct compatible strings.
Signed-off-by Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This currently reads the uclass's private data in the ofdata_to_platdata
method which is not allowed, since the uclass has not read it from the
device tree. This happens in the probe method.
Fix it by adding a probe() method and moving the code there.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is sometimes useful to process all children, making sure they are
probed first. Add functions to help with this and a macro to make it more
convenient.
Signed-off-by: Simon Glass <sjg@chromium.org>
When generating ACPI tables we need to make sure that all devices have
read their platform data, so that they can generate the tables correctly.
Rather than adding this code in ACPI, create a core function to handle it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to read a property from the chosen node, providing access
to its length. Update ofnode_get_chosen_string() to make use of it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we have ofnode_read_prop() we can rewrite this function using
that one, reducing the amount of duplicated code.
Update ofnode_read_size() and move it up next to the other similar
functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new function to read a property that supports reading the length as
well.
Reimplement ofnode_read_string() using it and fix its comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is actually intended to read a string rather than a
property. All of its current callers use it that way. Also there is no way
to return the length of the property from this function.
Rename it to better indicate its purpose, using ofnode_read as the prefix
since this matches most other functions.
Also add some tests which are missing for these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions do not modify the device so should use a const pointer to
it. Update the code accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions do not modify the device so should use a const pointer to
it. Update the code accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this method uses a non-const udevice pointer, but the call
should not modify the device. Use a const pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
-----BEGIN PGP SIGNATURE-----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=Sv9b
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- DFU support file operations lager then the default max size
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
Add DDR2 support to Gen5 DRAM driver. As the DDR2 macro names generated
by Quartus are named differently than the DDR3 ones, use anon unions to
store them in the same structures, without growing their size.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add optional support for fetching watchdog clock rate from DT
and ungating reset via reset framework. This is optional as not
all platforms using DW WDT support the clock and reset frameworks
yet.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
Convert the designware watchdog timer driver to DM and add DT probing
support. Perform minor coding style clean up, like drop superfluous
braces. These ought to be no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
Add DM_FLAG_OS_PREPARE flag to ensure that the driver's
remove() callback is invoked before booting the kernel.
This is required to stop the LCDIF controller. This was
the behaviour with old driver without DM_VIDEO support.
Without stopping the LCDIF we sometimes observe incorrect
Linux logo position.
Fixes: ae0760584b ("imx: mx6ul_14x14_evk: convert to DM_VIDEO")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Fix:
>>> CID 280902: Control flow issues (MISSING_BREAK)
>>> The case for value "VIDEO_BPP32" is not terminated
>>> by a 'break' statement.
Also fix
error: control reaches end of non-void function [-Werror=return-type]
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Various minor fixes for x86
- Switch to ACPI mode on Intel edison
- Support run-time configuration for NS16550 driver
- Update coreboot and slimbootloader serial drivers to use NS16550
run-time configuration
- ICH SPI driver fixes to hardware sequencing erase case
- Move ITSS from Apollo Lake to a more generic location
- Intel GPIO driver bug fixes
- Move to vs2017-win2016 platform build host for Azure pipelines
This adds DM_FLAG_PRE_RELOC flag to probe i2c driver
before relocation
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix the following in intel_gpio_get_value():
* The value of the register is contained in the variable 'reg', not in
'mode'. The variable 'mode' contains only the configuration whether
the gpio is currently an input or an output.
* The correct bitmasks for the input and output value are
PAD_CFG0_RX_STATE and PAD_CFG0_TX_STATE.
Use them instead of the currently used PAD_CFG0_RX_STATE_BIT and
PAD_CFG0_TX_STATE_BIT.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add missing 'PAD_CFG0_TX_STATE' to the clear mask for pcr_clrsetbits32().
Otherwise this bit cannot be cleared again after it has been set once.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The function pcr_clrsetbits32() expects a device with a P2SB parent
device. In intel_gpio_direction_output() and intel_gpio_set_value()
the device 'dev' is passed to pcr_clrsetbits32(), which is a
gpio-controller with a device 'pinctrl' as parent. This does not match
the expectations of pcr_clrsetbits32(). But the 'pinctrl' device has a
P2SB as parent.
Pass the 'pinctrl' device instead of the 'dev' device to
pcr_clrsetbits32().
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The watchdog timer value was never updated in the hardware by this
driver, so the watchdog triggered on some random stale value that
was left in the hardware. The TI SPRUH37C says, quote:
20.4.3.9 Modifying Timer Count/Load Values and Prescaler Setting
...
After a write access, the load register value and prescaler ratio
registers are updated immediately, but new values are considered
only after the next consecutive counter overflow or after a new
trigger command (the WDT_WTGR register).
This means at least one trigger must happen. The driver probably
depended on someone calling it's .reset() callback, however that
is not guaranteed e.g. if the WDT operates without servicing.
Add this missing trigger.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The timeout parameter of omap3_wdt_start() is in miliseconds, while
GET_WLDR_VAL() expects parameter in seconds. Fix this so the WDT
driver is actually usable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add "ti,keystone-gpio" compatible so as be able to use Linux DT files as
is.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
