The default configuration of the PMIC behavior makes the PMIC
power cycle most regulators on WDOG_B assertion. This power
cycling causes the memory contents of OCRAM to be lost.
Some systems neeeds some memory that survives reset and
reboot, therefore this patch is created.
The implementation is taken almost verbatim from Linux commit
2364a64d0673f ("regulator: pca9450: Make warm reset on WDOG_B assertion")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Now that a regulator driver exists for this PMIC, hook it up to the
device tree "regulators" subnodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This driver handles most voltage regulators found in X-Powers AXP PMICs.
It is based on, and intended to replace, the regulator driver in TF-A.
AXP PMIC regulators can be divided into 6 categories:
- Switches without voltage control => fully supported.
- Single linear range => fully supported.
- Two linear ranges, "step" and "2 * step" => fully supported.
- Two linear ranges, "step" and "5 * step" => only the first range is
supported. No boards are known to use the second range.
- Non-linear voltage values => fully supported.
- LDOs shared with GPIO pins => not supported.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Subordinate regulator drivers can use this enumerated ID instead of
matching the compatible string again.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Ignore the disabled children node in pmic_bind_children() so the
disabled regulators in device tree are not registered.
This patch is based on the dm_scan_fdt_node() code - only the
activated nodes are bound - and it solves possible issue when a
deactivated regulator is bound, error for duplicated regulator name
for example.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce the auto-generated clock tree and power domain data needed to
attach the am62a into the power-domain and clock frameworks of uboot
Signed-off-by: Bryan Brattlof <bb@ti.com>
This converts the following to Kconfig:
CONFIG_POWER_FSL
CONFIG_POWER_FSL_MC13892
CONFIG_POWER_HI6553
CONFIG_POWER_LTC3676
CONFIG_POWER_PFUZE100
CONFIG_POWER_PFUZE3000
CONFIG_POWER_SPI
CONFIG_POWER_TPS65090_EC
CONFIG_POWER_TPS65218
CONFIG_POWER_TPS65910
Signed-off-by: Tom Rini <trini@konsulko.com>
As we have more legacy PMIC drivers to move to Kconfig, guard them all
with POWER_LEGACY or SPL_POWER_LEGACY. Do the same kind of check for
building the drivers too. This also means that we need to resort the
list slightly in the Makefile.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The support added later in this series tweaks the PMIC voltages in the
SPL. Enable support for the rn5t567 in SPL builds to allow this to be done
cleanly.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for the rn5t568 PMIC to the rn5t567 driver.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Jaehoon Chung <j80.chung@samsung.com>
If the bd718x7 is required, but PMIC_CHILDREN is disabled, this
driver throws a compile error. Fix this by putting the function
to bind children into an if-statement checking for PMIC_CHILDREN.
Allowing PMIC_CHILDREN to be disabled in SPL saves some space and
still permits some read/write functions to access the PMIC in
early startup.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Avoid concatenation with following message.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If a regulator does not support .set_suspend_enable or
.set_suspend_value then ret is set to ENOSYS early in the function.
The most serious impact of this is that when no automatic setting of
voltage is needed then the final regulator_set_enable() is skipped
because ret has not been cleared.
It seems that the error handling for regulator_set_suspend_value() is
also wrong as if this succeeds then the normal boot-on checks are still
required, and again ENOSYS needs special treatment here.
Fixes: 11406b8f7e ("dm: regulator: support regulator more state")
Signed-off-by: John Keeping <john@metanate.com>
Use the log functions instead of pr_...() so we can avoid using __func__.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Since both pm8916.c and pm8916_gpio.c are already supporting multiple
Qcom SoCs, it makes sense to rename these drivers to pmic_qcom.c and
qcom_pmic_gpio.c respectively. Also, these driver can be extended to
support additional functionality if required for other Qcom SoCs.
Along with this import latest DT binding: qcom,spmi-pmic.txt from Linux
kernel and thereby remove pm8916.txt.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
In order to have the possibility to configure the regulators at system
startup through DM support, all LDOs and bucks must be able to be
changeable. Currently there is a limitation to change the values when
the output is enabled. Since the driver is based on the ROHM BD71837 and a
comment that describes a limitation about switching while the output is
enabled can also be found there, the limitation probably comes from this type.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
For Rockchip boards with the all rk8xx series PMICs (excluding the
rk808), it is sometimes desirable to not boot whenever the device is
plugged in. An example would be for the Odroid Go Advance.
This provides a configurable option to check the PMIC says it was
powered because of a plug-in event. If the value is 1 and this option
is selected, the device shuts down shortly after printing a message
to console stating the reason why it's shutting down. Powering up the
board with the power button is not affected.
This patch parallels the work done in the following patch series:
https://lore.kernel.org/u-boot/20220121133732.2397273-1-andre.przywara@arm.com/
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for sysreset shutdown for this PMIC. The values were pulled
from the various datasheets, but for now it has only been tested on
the rk817 (for an Odroid Go Advance).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tighten up symbol dependencies in a number of places. Ensure that a TPL
specific option has at least a direct dependency on TPL. In places
where it's clear that we depend on something more specific, use that
dependency instead.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
LDO5 has two separate control registers. LDO5CTRL_L is used if the
input signal SD_VSEL is low and LDO5CTRL_H if it is high.
The current driver implementation only uses LDO5CTRL_H. To make this
work on boards that have SD_VSEL connected to a GPIO, we add support
for specifying an optional GPIO and setting it to high at probe time.
In the future we might also want to add support for boards that have
SD_VSEL set to a fixed low level. In this case we need to change the
driver to be able to use the LDO5CTRL_L register.
This is a port of the same change in the Linux kernel:
8c67a11bae88 ("regulator: pca9450: Add SD_VSEL GPIO for LDO5")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Fabio Estevam <festevam@denx.de>
Update SCMI regulator controller driver to get its assigned SCMI channel
during initialization. This change allows SCMI voltage domain protocol
to use a dedicated channel when defined in the DT. The reference is
saved in SCMI regulator controller driver private data.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Changes SCMI driver API function devm_scmi_process_msg() to add
an SCMI channel reference argument for when SCMI agent supports
SCMI protocol specific channels. First argument of devm_scmi_process_msg()
is also change to point to the caller SCMI protocol device rather
than its parent device (the SCMI agent device).
The argument is a pointer to opaque struct scmi_channel known from
the SCMI transport drivers. It is currently unused and caller a pass
NULL value. A later change will enable such support once SCMI protocol
drivers have means to get the channel reference during initialization.
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
The pca9450 driver uses dm_i2c_{read,write}, which
are (unsurprisingly) only available with DM_I2C. Make sure one can't
create an unbuildable .config by adding proper dependencies.
While here, append "in SPL" to the prompt for the SPL_ variant so it
doesn't read the same as the one for the non-SPL_ variant.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Introduce autogenerated SoC data support clk and device data for the
AM62. Hook it upto to power-domain and clk frameworks of U-Boot.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add PCA9450 regulator driver. This is complementary driver for the BUCKn
and LDOn regulators provided by the PCA9450 PMIC driver. Currently the
driver permits reading the settngs and configuring the BUCKn and LDOn
regulators.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The upstream DT regulators node subnodes are named BUCKn and LDOn,
the downstream DT regulators node subnodes are named buckn and ldon,
add the upstream match.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The TPS65219 I2S PMIC features 3 Buck converters and 4 linear regulators,
2 GPOs, 1 GPIO, and 3 multi-function-pin.
This adds the driver for the Buck converters & linear regulators.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The TPS65219 I2S PMIC features 3 Buck converters and 4 linear regulators,
2 GPOs, 1 GPIO, and 3 multi-function-pin.
This adds the PMIC driver, loading the regulator sub-nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
There are expecte to be bars 0 through 5, but the last of these was
missing leading to an read beyond the buffer. Add the missing element
with zero values.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If dev_count_phandle_with_args returns 0 or another error, then pd will never
have been initialized by power_domain_get_by_index. Avoid comparing against
pd.dev in this situation.
Fixes: 3e4fcfa4bc ("power-domain: fix hang in endless loop on i.MX8")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add trivial driver for i.MX8MP HSIOMIX handling. This is responsible
for enabling the GPCv2 power domains and clock for USB 3.0 and PCIe
in the correct order. Currently supported is the USB 3.0 part which
can be tested, PCIe support should be easy to add.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX8MP power domain handling into the driver. This is based on the
Linux GPCv2 driver state which is soon to be in Linux next.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-gw74xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement power_domain_get_by_name() convenience function which parses
DT property 'power-domain-names' and looks up power domain by matching
name.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
This driver is the only SMCCC dependency in iMX8M U-Boot port. Rework
the driver based on Linux GPCv2 driver to directly control the GPCv2
block instead of using SMCCC calls. This way, U-Boot can operate the
i.MX8M power domains without depending on anything else.
This is losely based on Linux GPCv2 driver. The GPU, VPU, MIPI power
domains are not supported to save space, since they are not useful in
the bootloader. The only domains kept are ones for HSIO, PCIe, USB.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The arch/arm/include/asm/arch-imx8m/power-domain.h is not included
anywhere except in drivers/power/domain/imx8m-power-domain.c, just
inline the content and drop the header. No functional change.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
In case the power domain node structure is gpc@303a0000/pgc/power-domain@N,
do not bind power domain driver to the 'pgc' node, but rather descend into
it and only bind power domain drivers to power-domain@N subnodes. This way
we do not waste one useless driver instance associated with 'pgc' node.
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8mp-venice-defconfig
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
In case the ops is not implemented, return 0 in the core right away.
This is better than having multiple copies of functions which just
return 0 in each power domain driver. Drop all those empty functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
It is possible for power domain IDs to be great than 31. If this
happens, the PTCMD and PTSTAT registers must overflow into adjacent
corresponding PTCMD_H and PTSTAT_H registers for each. Update the driver
to account for this.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
This commit adds the possibility to choose the compatible
"regulator-fixed-clock" in devicetree.
This is a special case of regulator-fixed where a clock has to
be used to switch the regulator on and off.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add DT compatible string for PCA9450C PMIC. This is a variant of the
PCA9450 PMIC with 6 A dual-phase buck regulator and 3 A buck regulator,
and is software-wise compatible with the PCA9450B. This variant of the
PCA9450 is designed for use as companion PMIC for i.MX8MP.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The tps65217 PMIC driver is used with am335x SoC based designs.
It is used in the SPL (MLO) as well, so the DM conversion only is
for u-boot proper.
This driver only allows simple reading/writing/dumping of the content
of its registers and requires the DM_I2C for proper operation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Up till now the CONFIG_POWER_TPS65217 has been defined in several header
files for am335x SoC.
This patch renames it to CONFIG_PMIC_TPS65217, which better reflects the
role of this IC circuit.
Moreover, new CONFIG_PMIC_TPS65217 has been introduced in Kconfig
to be used with boards, which both support DM_PMIC and DM_I2C.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Migrate all other platforms as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYjIBkgAKCRDKSWXLKUoM
IYUwAKCYRBxb59BFq4MRvTbNcRZ7H4oGIQCfVUl3x9KZ7nFZaYAaBXFBxwna+PE=
=irCR
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.07-rc1
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
Changes devm_scmi_process_msg() first argument from target parent device
to current SCMI device and lookup the SCMI agent device among SCMI device
parents for find the SCMI agent operator needed for communication with
the firmware.
This change is needed in order to support CCF in clk_scmi driver unless
what CCF will fail to find the right udevice related to exposed SCMI
clocks.
This patch allows to simplify the caller sequence, using SCMI device
reference as parameter instead of knowing SCMI uclass topology. This
change also adds some protection in case devm_scmi_process_msg() API
function is called for an invalid device type.
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Buck regulator 1, 2 and 3 of TPS6594132 on j721e-sk is in 3 Phase
confguration, in-order to support this, add configuring 3 Phase buck
in tps65941 while driver probing.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Since TPS659412 and TPS659413 are both software compatible,
add a compatible string for the same inside tps65941.c.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Driver should be enabled by CONFIG_POWER_DOMAIN=y and
CONFIG_ZYNQMP_POWER_DOMAIN=y. Power domain driver doesn't have own DT node
but it uses zynqmp firmware DT node that's why there is a need to bind
driver when firmware node is found.
Driver itself is simple. It is sending pmufw config object overlay for
enabling access to device which is done in ...domain_request().
In ...domain_on() capabilities are passed and node is requested.
This should be bare minimum of required to get power domain driver working.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/f4b9433b91c0b18c375b061c7a4e29d428f70547.1644226055.git.michal.simek@xilinx.com
The power management controller found on Apple SoCs als provides
a way to reset all devices within a power domain. This is needed
to cleanly shutdown the NVMe controller before we hand over
control to the OS.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested on: Macbook Air M1
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
When regulator consumer attempts to set enabled DVS regulator voltage,
the driver aborts with "Only DVS bucks can be changed when enabled".
In case the regulator is already set to specified voltage, do nothing
instead of failing outright.
When regulator consumer attempts to set enables regulator which cannot
be controlled because it is already always enabled, the driver aborts
with -EINVAL. Again, do nothing in such case and return 0, because the
request is really fulfilled, the regulator is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
This driver supports power domains for the power management
controller found on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
The AXP PMICs have the ability to power off the system. The existing
code for this is duplicated for each PMIC variant, and uses the legacy
non-DM "pmic_bus" interface. When SYSRESET is enabled, this can all be
replaced with a sysreset device using the DM_PMIC interface.
Since the trigger bit is the same on all PMIC variants, use the register
definitions from the oldest supported PMIC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The sysreset uclass has an option to provide the do_poweroff() function.
When that option is enabled, the AXP power drivers should not provide
their own definition.
For the AXP305, which is paired with 64-bit systems where TF-A provides
PSCI, there is another possible conflict with the PSCI firmware driver.
This driver can be enabled even if CONFIG_PSCI_RESET is disabled, so
make sure to use the right symbol in the condition.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
These PMICs provide some combination of battery charger, fuel gauge,
GPIOs, regulators, and VBUS routing. These functions are represented
as child nodes in the device tree. Add the minimal driver needed to
probe these child devices and provide the DM_PMIC ops.
Enable the driver by default for SoCs that normally pair with a PMIC.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Now that there is a separate symbol to enable DM_PMIC in SPL, update the
the SPL-specific driver symbols to depend on this new option.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Kconfig symbols for two PMIC drivers (PMIC_AS3722 and DM_PMIC_MC34708)
were missing a dependency on DM_PMIC. To fix this inconsistency, and to
keep it from happening again, wrap the driver section with "if DM_PMIC"
instead of using a "depends on DM_PMIC" clause for each driver.
Reviewed-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.
Some files did not contain any GPIO code at all, so this header was
completely unused.
A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.
The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Move the power/ rules into drivers/power to avoid clutter in the Makefile
and drivers/Makefile files.
We must select SPL_POWER if SPL_POWER_DOMAIN is used, since the two are
currently independent and boards do not necessarily enable SPL_POWER.
Add a TPL_POWER as well, as that is used by one board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
At present we have SPL_POWER but not piain POWER. This works because
there is a special build rule in Makefile that always includes the
drivers/power directory.
It is better to have all driver directories included by drivers/Makefile
and there is already a rule in there for this purpose. It just needs a
Kconfig for U-Boot proper, so add one.
Update the pmic.h header file so that it defines the old pmic struct
always, when driver model is not in use. That will avoid build errors
for boards which enable POWER but not DM_PMIC.
Enable this option always. That seems strange at first sight, but it
actually but mimics the current Makefile behaviour. Once we can drop the
old PMICs it should be easy enough to rename DM_PMIC to POWWER, or
something similar.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_POWER_I2C
CONFIG_POWER_LEGACY
They are handled at the same time due to a dependency between them.
Update the Makefile rule to use legacy power only in U-Boot proper.
Unfortunately a separate rule is needed in SPL to be able to build
legacy power. Add SPL related symbols for both, to allow for SPL-only
usage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: More SPL related cleanups, reword commit message]
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is used in pre-driver model code and much of it has never
been converted to driver model.
We want to add a new option to enable power support, so we can use a
simple rule in the Makefile. Rename this one, which is really about
a particular implementation of power.
Also update the pmic.h header file so it either includes the legacy
API or the driver model one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a proper Kconfig option for SPL so we can remove the hack in some of
the board config files.
This involves adding CONFIG_SPL_DM_PMIC to some of the configs as well
as updateing the Makefile rule for PMIC_RK8XX to exclude SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Add SPL_PMIC_RK8XX, enable when needed, handle undef of
CONFIG_DM_PMIC_PFUZE100 as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename this option so that CONFIG_IS_ENABLED can be used with it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
TI J7200 EVM has lp876441 pmic that is similar to tps65941. Add support
for same with existing driver with new compatible.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/20210714205300.17424-2-g-tammana@ti.com
