Commit graph

4008 commits

Author SHA1 Message Date
Michael Walle
8331618cc3 board: sl28: drop unneeded and outdated flash partitions
This board doesn't use the MTD subsystem in u-boot, thus there is no
need to specify the partitions. They are outdated anyway. Just drop
them.

Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-08-18 15:55:15 +05:30
Marek Vasut
59f6eb477e ARM: dts: stm32: Reduce DHCOR SPI NOR frequency to 50 MHz
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM,
which causes additional signal delay. At 108 MHz, this delay triggers
a sporadic issue where the first bit of RX data is not received by the
QSPI controller.

There are two options of addressing this problem, either by using the
DLYB block to compensate the extra delay, or by reducing the QSPI bus
clock frequency. The former requires calibration and that is overly
complex for SPL, so opt for the second option. This incurs 20ms delay
during boot, when SPL loads U-Boot to DRAM.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-08-16 10:49:35 +02:00
Patrick Delaunay
2d4180b1eb arm: dts: stm32mp15: alignment with v5.14
Device tree alignment with Linux kernel v5.14-rc3
- ARM: dts: stm32: move stmmac axi config in ethernet node on stm32mp15
- ARM: dts: stm32: Configure qspi's mdma transfer to block for stm32mp151
- ARM: dts: stm32: add a new DCMI pins group on stm32mp15
- ARM: dts: stm32: fix ltdc pinctrl on microdev2.0-of7

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-08-16 10:49:35 +02:00
Patrick Delaunay
b73e8bf453 arm: stm32mp: add defconfig for trusted boot with FIP
Add TF-A FIP support for trusted boot on STM32MP15x,
when STM32MP15x_STM32IMAGE is not activated.

With FIP support the SSBL partition is named "fip" and its size is 4MB,
so the ENV partition name in device tree  (for SD card or eMMC)
or offset in defconfig (CONFIG_ENV_OFFSET / CONFIG_ENV_OFFSET_REDUND)
need to be modified.

With FIP the TEE MTD partitions are removed because the OP-TEE binray are
included in the FIP containers.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-08-16 09:36:31 +02:00
Patrick Delaunay
f91783edf2 arm: stm32mp: handle the OP-TEE nodes in DT with FIP support
With FIP support in TF-A (when CONFIG_STM32MP15x_STM32IMAGE
is not activated), the DT nodes needed by OP-TEE are added by OP-TEE
firmware in U-Boot device tree, present in FIP.

These nodes are only required in trusted boot, when TF-A load the file
u-boot.stm32, including the U-Boot device tree with STM32IMAGE header,
in this case OP-TEE can't update the U-Boot device tree.

Moreover in trusted boot mode with FIP, as the OP-TEE nodes are present
in U-Boot device tree only when needed the function
stm32_fdt_disable_optee can be removed.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-08-16 09:34:27 +02:00
Chris Morgan
d70c0cab8f rockchip: px30: add support for SFC for Odroid Go Advance
The Odroid Go Advance uses a Rockchip Serial Flash Controller with an
XT25F128B SPI NOR flash chip. This adds support for both. Note that
while both the controller and chip support quad mode, only two lines
are connected to the chip. Changing the pinctrl to bus2 and setting tx
and rx lines to 2 for this reason.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-12 09:34:11 +08:00
Chris Morgan
08b097c32f rockchip: px30: add the serial flash controller
Add the serial flash controller to the devicetree for the PX30.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-12 09:34:11 +08:00
Peter Robinson
100583473c arm: dts: sync the Rockhip 3368 SoCs from Linux
Sync the rk3368 DTs and associated bits from 5.14-rc1.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-12 09:33:13 +08:00
Peter Robinson
27e1b5ee9b arm: dts: sync the Rockhip 3328 SoCs from Linux
Sync the rk3328 DTs and associated bits from 5.14-rc1.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-12 09:33:13 +08:00
Peter Robinson
822556a934 arm: dts: sync the Rockhip 3399 SoCs from Linux
Sync the rk3399 DTs and associated bits from 5.14-rc1.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
(Remove the conflict content for vmarc-som)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-12 09:33:13 +08:00
Xiaobo Tian
09cf012467 arm64: rk3399: r4s: Remove undesirable MAC address fetching methods for ethernet
Remove the recommended MAC address from the network card.
NanoPi R4S has a EEPROM attached to the 2nd I2C bus (U92), which stores the MAC address.

Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11 18:10:39 +08:00
Xiaobo Tian
897f30e84a arm64: rk3399: r4s: Inheritance uses the sdmmc definition in dtsi
The host-index-min property is invalid,
so it inherits from the sdmmc definition in dtsi.

Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11 18:10:39 +08:00
Xiaobo Tian
2ae7dacfaf arm64: rk3399: r4s: correct the LEDS label name
Correct the LEDS label name and remove the board type prefix,
which is actually unnecessary here, removes the redefined system status LED pin.

Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11 18:10:39 +08:00
Johan Jonker
d2a74ec91b ARM: dts: rockchip: update rk3188-radxarock.dts
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-radxarock-u-boot.dtsi file.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11 17:54:37 +08:00
Johan Jonker
7d4b5a850e ARM: dts: rockchip: update rk3188.dtsi
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-u-boot.dtsi file.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11 17:54:37 +08:00
Johan Jonker
2ee023d293 ARM: dts: rockchip: update rk3xxx.dtsi
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. This file has recently had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3xxx-u-boot.dtsi file.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2021-08-11 17:54:37 +08:00
Peng Fan
3f2b4d7220 arm: imx: add i.MX8ULP EVK support
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART

Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.

U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT:   Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE:  BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE:  BL31: Built : 01:56:58, Jun 29 2021
NOTICE:  upower_init: start uPower RAM service
NOTICE:  user_upwr_rdy_callb: soc=b
NOTICE:  user_upwr_rdy_callb: RAM version:12.6

U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)

CPU:   Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM:  2 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment

In:    serial@293a0000
Out:   serial@293a0000
Err:   serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-08-09 14:46:51 +02:00
Peng Fan
6beec0e78c arm: dts: add i.MX8ULP dtsi
Add i.MX8ULP dtsi

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-08-09 14:46:51 +02:00
Fabio Estevam
1d1f3c8099 mx28evk: Convert to driver model
Make the conversion to driver model as it is mandatory.

Successfully tested booting Linux from the SD card.

Dropped support for networking and splash screen as these need
to be properly converted to DM and tested.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-08-09 14:46:50 +02:00
Sebastian Reichel
3bbc48e8f1 board: ge: bx50v3: Add PCIe reset to DT
Add PCIe reset gpio to the Bx50v3 devicetree and get get rid of
CONFIG_PCIE_IMX_PERST_GPIO.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
a8a72c3ce9 board: gateworks: venice: add imx8mm-gw7902 support
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC

Do the following to add support for it:
- add dts
- add PMIC config

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
42bc70d14a arm: dts: imx8mm-venice-gw7901: use common u-boot dtsi
Use the common imx8mm-u-boot.dtsi

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
aea162c10e arm: dts: imx8mm-venice-gw700x: fix fifo-depth phy props
Replace the deprecated 'tx-fifo-depth' and 'rx-fifo-depth' properties
not supported by U-Boot drivers/net/phy/dp83867.c with the proper
'ti,fifo-depth' property.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
98559e02f1 arm: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12
is the power-enable to the TPS25821 Source controller and power switch
responsible for monitoring the CC pins and enabling VBUS. Therefore
GPIO1_12 must always be enabled and the vbus output enable from the
IMX8MM can be ignored.

To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the
TPS25821 and change the regulator output to GPIO1_10 which is
unconnected.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
a194e6ed45 imx: ventana: remove hard-coded USB OTG pinmux
pinmux is now done via dt. Add missing OTG_OC pinmux for boards that
use it.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Tim Harvey
dd79c97b92 imx: ventana: fix UMS support
The Gateworks Ventana boards have always had usb0=usbh1 and usb1=usbotg
because OTG is often subloaded on these boards and a bit in the EEPROM
which flagging that OTG is subloaded is used to remove the dt node via the
alias.

U-Boot DM_USB UMS requires the usb0 alias be assigned to the usbotg
so fix the usb0 alias in order for UMS to work.

Fixes 72c46327f0: ("imx: ventana: enable dm support for USB")

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2021-08-09 14:46:50 +02:00
Fabio Estevam
3f24bd329b imx28-evk: Import devicetree file from Linux
Import the imx28-evk devicetree files from Linux kernel
version 5.11-rc7.

This is in preparation for converting the mx28evk_defconfig
target to driver model.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-08-06 13:26:08 +02:00
Tom Rini
b91c704333 Merge https://source.denx.de/u-boot/custodians/u-boot-samsung 2021-08-03 09:07:01 -04:00
Tom Rini
5371593aed Merge https://source.denx.de/u-boot/custodians/u-boot-sunxi
- Move the PSCI runtime code for H3/A23/A33 into SRAM
- Pick the environment from the actual MMC boot device (SD card vs.
  eMMC)
- Plus a small improvement from Icenowy, just for good measure.
2021-07-31 20:51:24 -04:00
Icenowy Zheng
001ec430be sunxi: decide the inclusion of SCP by SCP_ADDR existence
There are more Allwinner SoCs that do not have a SCP now.

When there's no SCP_ADDR macro defined, we can assume there's no SCP
available.

Drop the scp part of FIT description when SCP_ADDR does not exist.

Signed-off-by: Icenowy Zheng <icenowy@sipeed.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-08-01 00:11:34 +01:00
Tom Rini
38436abd5e Merge tag 'ti-v2021.10-rc2' of https://source.denx.de/u-boot/custodians/u-boot-ti
- Add MMC High speed modes for AM64 and J7200
- Add Sierra/Torrent SERDES driver
- Minor clean-ups for R5F boot from SPL
2021-07-29 08:20:06 -04:00
Tom Rini
55efa84d0f - Add SMBIOS info for Khadas VIM boards
- Fix meson-axg-mipi PHY build
 - Fix VIM3 board phy-names property setup
 - Return correct value for non emmc boot sources on VIM3
 - add kernel compression vars
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmD/0m0ACgkQd9zb2sjI
 SdHOuhAAzKV5VKWFjz+kxAWLhIeVqK1DixVkA8qMLNE9LYfF2ibv89yM0jaTQv84
 Zs4J9ak9xC2/LQPX7ui9CzAZ53yi7qM28aQd4MzRPBha0al8dehRZdcGNTRV/WBb
 CnbwW5inx2J1e+KSZ2PVqOnCTVX39ZMdEbZnxIJmSCcgrwj1eCPUzMv0wD0fqhyq
 piAbOpKLO6v1k/p4veTCa8gEimpp1Ni4QKqeLxkZ54hrt+uvrQbb7HxqfXuGwNG4
 IWnkfocZXN6nUbjNh7NitGgRZCMtiKJSgXrwlmluXoi0OyUNwxX7Fbn9JqsbWpMR
 lqFVJxbJ4jGozWK5wb5jcT5PArVkYgr+FN7lmqefysEltBjpv0JWqdxKH44RteyA
 wA4yPz/5Oe/iZJu9h2GzHuFHma2Dr8z43NrsIO/cTKN5uG9gzbKbp8IxV2P715OZ
 R5XPzSHLFD1Q/A855yKxvF1tlizSDdKo2pXZ2BfvLBZEljd37QmVkRSy+gPL3QhD
 bMICPJ1opuJZb9dEi0L54yk9+tm4ImWTuYRNOsFc4p9EGT4P9yydqMkpzuuHXRJb
 GcLoD+TXgoxK8PijX9QWdQPnb0FkFKShwWMXOn9zyzIDIzT4HlZN8HtyPCYmbyD1
 6uFWiQQEfvbzInPmQpgk5mZoblskMSI/pN+4KHKlH3X4yWK5YGQ=
 =zrJm
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-amlogic-20210727' of https://source.denx.de/u-boot/custodians/u-boot-amlogic

- Add SMBIOS info for Khadas VIM boards
- Fix meson-axg-mipi PHY build
- Fix VIM3 board phy-names property setup
- Return correct value for non emmc boot sources on VIM3
- add kernel compression vars
2021-07-27 11:42:31 -04:00
Artem Lapkin
e10481be1e ARM: dts: meson: Use devicetree for SMBIOS settings for Khadas VIM boards
Khadas vim series: Use devicetree for SMBIOS settings
Add settings and enable the default sysinfo driver so that these can come
from the device tree.

Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Artem Lapkin <art@khadas.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2021-07-27 10:32:59 +02:00
Alexandru Gagniuc
65b3f56d42 ARM: dts: stm32mp: Add OP-TEE reserved memory to SPL dtb
Add the "/reserved-memory/optee" node to the SPL devicetree. The
purpose is to allow configuring TZC regions when booting OP-TEE.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-07-27 09:48:11 +02:00
Marek Vasut
59000ebe0b ARM: dts: stm32: Fix AV96 eMMC pinmux
Commit 500327e2ea ("ARM: dts: stm32mp1: DT alignment with Linux kernel v5.8-rc1")
renamed sdmmc2_d47_pins_b phandle to sdmmc2_d47_pins_c, but without updating
the AV96 DT which uses that phandle. Linux missed similar update as well and
it was only added in commit 1ad6e36ec266 ("ARM: dts: stm32: Fix sdmmc2 pins
on AV96") .

Update the AV96 DT pinmux phandle, otherwise eMMC 8bit mode does not work
and access to eMMC takes a very long time to fall back to 4bit mode.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
2021-07-27 09:47:40 +02:00
Patrick Delaunay
2a7034c77d stm32mp1: add pull-up for gpio button PA13 and PA14
When a push-button is released and PA13/PA14 are defined as input (high-Z)
the LED should not be active as the circuit is open but a small current
leak through PCB or push-button close the circuit and allows a small LED
bias giving erroneous level voltage.

So it is recommended to activate an internal pull-up in order to clearly
fix the voltage at PA13/PA14 when button is released and to wait
a short delay before to read the GPIO value only when the pull-up is
correctly configured.

Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
2021-07-27 09:47:40 +02:00
Suman Anna
24f3fb6547 arm: dts: k3-j721e-r5: Remove MAIN R5FSS0 cluster from SPL
The MAIN R5FSS0 cluster and corresponding nodes are no longer required
to be enabled in R5 SPL after removing the support for booting any core
from this cluster on R5 SPL. So, remove these from the relevant dts
files.

This is essentially a revert of the additions done in commit 2984b82b3b
("arm: dts: k3-j721e-r5: Enable r5fss0 cluster in SPL").

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726211311.5977-5-s-anna@ti.com
2021-07-27 11:00:44 +05:30
Suman Anna
31b3d7a018 arm: dts: k3-am65: Fix up MCU R5FSS cluster mode back to Split-mode
The default U-Boot environment variables and design are all set up to
have the MCU R5FSS cluster to be in Split-mode. This is the setting
in v2021.01 U-Boot and the dt nodes are synched with the kernel binding
property names in commit 468ec2f3ef ("remoteproc: k3_r5: Sync to
upstreamed kernel DT property names") merged in v2021.04-rc2.

The mode for the cluster got switched back to LockStep mode by mistake
in commit e497876343 ("arm: dts: k3-am65: Sync Linux v5.11-rc6 dts
into U-Boot") also in v2021.04-rc2. This throws the following warning
messages when early-booting the cores using default env variables,

  k3_r5f_rproc r5f@41400000: Invalid op: Trying to start secondary core 2 in lockstep mode
  Load Remote Processor 1 with data@addr=0x82000000 65268 bytes: Failed!

Fix this by switching back the cluster to the expected Split-mode.
Make this mode change in the u-boot specific dtsi file to avoid such
sync overrides in the future until the kernel dts is also switched to
Split-mode by default.

Fixes: e497876343 ("arm: dts: k3-am65: Sync Linux v5.11-rc6 dts into U-Boot")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726162213.28719-1-s-anna@ti.com
2021-07-27 11:00:10 +05:30
Aswath Govindraju
0817dd5432 arch: dts: am642-sk-u-boot: Disable main_sdhci0 DT node and define alias index 1 for main_sdhci1 node
A Wilink wireless device is connected to MMCSD0 subsystem and is not
supported in U-Boot. Therefore, disable main_sdhci0 device tree node in
U-Boot.

If main_sdhci0 device tree node is disabled then the the index of
main_sdhci1 node becomes 0 which leads to break in boot flow. Therefore,
add an alias to fix the index to 1.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210726152807.22991-3-a-govindraju@ti.com
2021-07-27 10:58:49 +05:30
Aswath Govindraju
08189ffd15 arm: dts: k3-j7200-common-proc-board-u-boot: Add u-boot tags for torrent serdes
Add u-boot tags for torrent serdes. This has properties specific to
u-boot on top of DT in v5.13 Linux Kernel.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-15-kishon@ti.com
2021-07-27 10:57:12 +05:30
Aswath Govindraju
cbea79867e arm: dts: k3-j7200-common-proc-board: Enable SERDES DT
Add default lane function for torrent serdes. This is in sync
with v5.13 Linux Kernel.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-14-kishon@ti.com
2021-07-27 10:57:12 +05:30
Aswath Govindraju
6c4be8eb7e arm: dts: k3-j7200-main: Add DT node for torrent serdes
Add DT node for torrent serdes. This is in sync with v5.13 Linux Kernel.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-13-kishon@ti.com
2021-07-27 10:57:12 +05:30
Kishon Vijay Abraham I
ad256cc894 ARM: dts: k3-j721e: Add support for USB3 in USB0 instance
Configure the parent clock of wiz3_pll0_refclk to the internal clock
required for USB3 to be functional and also remove "ti,usb2-only"
property as it now supports USB3 mode. This has properties specific to
u-boot on top of DT present in v5.13 of Linux Kernel.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210721155849.20994-12-kishon@ti.com
2021-07-27 10:57:12 +05:30
Paul Barker
124b3030f5 arm: dts: Import am335x-sancloud-bbe devicetree
This device tree is imported from Linux 5.13.1 and enabled via the
am335x board file and the am335x evm defconfig.

Signed-off-by: Paul Barker <paul.barker@sancloud.com>
2021-07-27 10:56:09 +05:30
Paul Barker
942853dd96 arm: dts: Resync BeagleBone device trees
These device trees are updated to match the versions in Linux 5.13.1.
The tick-timer entry in am335x-bone-common.dtsi is preserved.

Signed-off-by: Paul Barker <paul.barker@sancloud.com>
2021-07-27 10:56:09 +05:30
Aswath Govindraju
455f9dddc8 arm: dts: k3-j7200-main: Add support for HS400 and update delay select values for MMCSD subsystems
HS400 speed mode is now supported in J7200 SoC[1]. Therefore add
mmc-hs400-1_8v tag in sdhci0 device tree node.

Also update the delay values for various speed modes supported, based on
the revised january 2021 J7200 datasheet[2].

[1] - section 12.3.6.1.1 MMCSD Features, in
      https://www.ti.com/lit/ug/spruiu1a/spruiu1a.pdf,
      (SPRUIU1A – JULY 2020 – REVISED JANUARY 2021)

[2] - https://www.ti.com/lit/ds/symlink/dra821u.pdf,
      (SPRSP57B – APRIL 2020 – REVISED JANUARY 2021)

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210525093826.10390-3-a-govindraju@ti.com
2021-07-27 10:56:09 +05:30
Simon Glass
5e19f4aa13 samsung: exynos: Convert SROMC interface to a driver
Add a bus driver for this and use it to configure the bus parameters for
the Ethernet interface. Drop the old pre-driver-model code.

Switch over to use driver model for Ethernet.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2021-07-27 10:34:27 +09:00
Manish Narani
15ca9ebb07 arm64: zynqmp: Move USB3 PHY properties from DWC3 node to USB node
Move the PHY properties from DWC3 node to USB node in ZynqMP DTs as here
the USB3 PHY used is PSGTR, which is connected to Xilinx USB core. This
PHY initialization should be handled from Xilinx USB core as the
prerequisite register configurations are done here only.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-07-26 09:26:41 +02:00
Piyush Mehta
d036f4f2c6 arm64: dts: zynqmp: Enable USB2.0 for zc1751-xm016-dc2
The board zynqmp-zc1751-xm016-dc2 support only USB2.0.
This patch removes USB3.0 DT configuration for DC2 board.

Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-07-26 09:18:45 +02:00
Masami Hiramatsu
11cd1d6a34 dts: synquacer: Add partition information to the spi-nor
Add partition information to the spi-nor flash.
This is required for accessing NOR flash via mtdparts.

Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2021-07-23 18:53:45 -04:00