We only need to read in the size of struct image_header and thus don't
need to know the page size of the nand device.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Before this patch it was only possible to access the default eMMC HW
partition. By partition selection I mean the access to eMMC via the
ext_csd[179] register programming.
It sometimes happens that it is necessary to write to other partitions.
This patch adds extra attribute to "raw" sub type of the dfu_alt_info
environment variable (e.g. boot-mmc.bin raw 0x0 0x200 mmcpart 1;)
It saves the original boot value and restores it after storing the file.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Since dfu_flush() can write raw data, dfu_write() with zero size
can be removed from download_tail() in thor gadget.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Before dfu write and flush operations separation,
dfu write data was flushed by host download request
with len of zero size.
Since above change manually calling dfu write with zero
size has non sense (e.g. in THOR). This should be done by
flush operation.
So now dfu_write_buffer_drain() is called in dfu_flush().
If there is any raw data to flush (like it can be in thor)
then it will be physically written to medium.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
ci_udc only allocates a single QTD structure per EP. All data needs to be
extracted from the DTD prior to calling ci_ep_submit_next_request(), since
that fills the QTD with next transaction's parameters. Fix
handle_ep_complete() to extract the transaction (remaining) length before
kicking off the next transaction.
In practice, this only causes writes to UMS devices to fail for me. I may
have tested the final versions of my previous ci_udc patch only with
reads. More recently, I had patches applied locally that allocated a QTD
per USB request rather than per USB EP, although since that doesn't give
any performance benefit, I'm dropping those.
Fixes: 2813006fec ("usb: ci_udc: allow multiple buffer allocs per ep")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
A few changes are made to the Tegra EHCI driver so that it can set
everything up for device-mode operation on the first USB controller.
This can be used in conjunction with ci_udc.c to operate as a USB
device.
Detailed changes are:
* Rename set_host_mode() to set_up_vbus() since that's really what it
does.
* Modify set_up_vbus() to know whether it's initializing in host or
device mode, and:
- Skip the external VBUS check in device mode, since external VBUS is
expected in this case.
- Disable VBUS output in device mode.
* Modify init_phy_mux() to know whether it's initializing in host or
device mode, and hence skip setting USBMODE_CM_HC (which enables host
mode) in device mode. See the comments in that function for why this
is safe w.r.t. the ordering requirements of PHY selection.
* Modify init_utmi_usb_controller() to force "b session valid" in device
mode, since the HW requires this. This is done in UTMI-specific code,
since we only support device mode on the first USB controller, and that
controller can only talk to a UTMI PHY.
* Enhance ehci_hcd_init() to error-check the requested host-/device-mode
vs. the dr_mode (dual-role mode) value present in device tree, and the
HW configurations which support device mode.
* Enhance ehci_hcd_init() not to skip HW initialization when switching
between host and device mode on a controller. This requires remembering
which mode the last initialization used.
Cc: Jim Lin <jilin@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Both init_{utmi,ulpi}_usb_controller() have nearly identical code for
PHY type selection. Pull this out into a common function to remove the
duplication.
Cc: Jim Lin <jilin@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The TRM for Tegra30 and later all state that USBMODE_CM_HC must be set
before writing to hostpc1_devlc to select which PHY to use for a USB
controller. However, neither init_{utmi,ulpi}_usb_controller() do this
today, so the register writes they perform for PHY selection do not
work.
For the UTMI case, this was hacked around in commit 7e44d9320e "ARM:
Tegra: USB: EHCI: Add support for Tegra30/Tegra114" by adding code to
ehci_hcd_init() which sets USBMODE_CM_HC and duplicates the PHY
selection register write. This code doesn't cover the ULPI case, so I
wouldn't be surprised if ULPI doesn't work with the current code, unless
the ordering requirement only ends up being an issue in HW for UTMI not
ULPI.
This patch fixes init_{utmi,ulpi}_usb_controller() to correctly set
USBMODE_CM_HC before selecting the PHY. Now that this works, we can
remove the duplicate UTMI-specific code in ehci_hcd_init(), thus
simplifying that function.
Cc: Jim Lin <jilin@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
These are used only once, so their is no need to have them global.
This also stops mvtwsi from using any bss vars making it easier to use
before dram init (to talk to the pmic to set the dram voltage).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The TWSI_FREQUENCY macro was wrong in 2 ways:
1) It was casting the result of the calculations to an u8, while i2c clk
rates are often >= 100Khz which won't fit in a u8, drop the cast.
2) It had an extra factor of 2 in the divider which neither the datasheet nor
the Linux driver have.
The comment for the default value was wrongly saying that m lives in
bits 4-7, while in reality it is in bits 3-6, as can be seen from the correct
shift by 3 used in i2c_init().
While at it remove the unused twsi_actual_speed variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
ps7_init.c and ps7_init.h are supposed to be exported by hw project
and copied to board/xilinx/zynq/ directory.
We want them to be ignored by git.
So what we should do is to always treat them as external files
rather than replacing ps7_init.c
This commit does:
- Move a weak function ps7_init() to arch/arm/cpu/armv7/zynq/spl.c
and delete board/xilinx/zynq/ps7_init.c
- Compile board/xilinx/zynq/ps7_init.c only when it exists
- Add .gitignore to ignore ps7_init.c/h
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ps7_init.c exported by hw project has #include "xil_io.h" line
but U-Boot does not have "xil_io.h".
So we get an error on SPL build:
ps7_init.c:12581:20: fatal error: xil_io.h: No such file or directory
We can delete the include directive in ps7_init.c to avoid this error.
But it is painful to do this every time we export ps7_init.c file.
Instead, we can put an empty xil_io.h in the same directory
so we can directly copy ps7_init.c as is.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Moved the USB/SD/MMC common FAT configs separately
to avoid redefinition warnings.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added configs to support USB host for zynq boards.
Also added a command usbboot to boot from usb.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extend max kernel image size. Gunzip is checking
this value. If kernel is larger, message below is shown.
Uncompressing Kernel Image ... Error: inflate() returned -5
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When CONFIG_FPGA is defined but CONFIG_SPL_FPGA is not, the build fails:
board.c: In function 'board_init':
board.c:41:3: error: 'fpga' undeclared (first use in this function)
fpga = fpga010;
Fix this by expanding the "#if.." around this block to match the other
FPGA checks and don't compile this block when buildign for SPL without
FPGA support.
Tested a bootloader that had CONFIG_FPGA defined without CONFIG_SPL_FPGA,
this now compiles without errors and loading FPGA from u-boot works.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Bootmode mask was defined as 0x0F, but documentation mentions 0x07.
Experiments show that bit "3" is the JTAG chain configuration.
Change the mask to "7" to allow systems with a different chain
configuration to boot correctly.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The driver should setup slcr state according
to slcr operations.
Reported-by: Andrey Filippov <andrey@elphel.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Fix c&p error in zynq_slcr_devcfg_enable() commentary
and extending it with description according
to Zynq TRM also in zynq_slcr_devcfg_disable().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Memory size should be specified without ECC place.
If you need to have half memory size, please change
u-boot configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added efuse status register base address. This register
is used for determining whether efuse was blown or not.
Also, added the zynq_get_silicon_version() to get the
silicon version of the zynq board.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Warnings:
board/xilinx/zynq/board.c:17:13: warning: symbol 'fpga' was not declared. Should it be static?
board/xilinx/zynq/board.c:20:13: warning: symbol 'fpga010' was not declared. Should it be static?
board/xilinx/zynq/board.c:21:13: warning: symbol 'fpga015' was not declared. Should it be static?
board/xilinx/zynq/board.c:22:13: warning: symbol 'fpga020' was not declared. Should it be static?
board/xilinx/zynq/board.c:23:13: warning: symbol 'fpga030' was not declared. Should it be static?
board/xilinx/zynq/board.c:24:13: warning: symbol 'fpga045' was not declared. Should it be static?
board/xilinx/zynq/board.c:25:13: warning: symbol 'fpga100' was not declared. Should it be static?
board/xilinx/zynq/board.c:120:5: warning: symbol 'board_mmc_init' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Warnings:
arch/arm/cpu/armv7/zynq/slcr.c:21:6: warning: symbol 'zynq_slcr_lock' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:27:6: warning: symbol 'zynq_slcr_unlock' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:34:6: warning: symbol 'zynq_slcr_cpu_reset' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:54:6: warning: symbol 'zynq_slcr_gem_clk_setup' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:81:6: warning: symbol 'zynq_slcr_devcfg_disable' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:94:6: warning: symbol 'zynq_slcr_devcfg_enable' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:107:5: warning: symbol 'zynq_slcr_get_boot_mode' was not declared. Should it be static?
arch/arm/cpu/armv7/zynq/slcr.c:113:5: warning: symbol 'zynq_slcr_get_idcode' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds the Gumstix Pepper[1] single-board computer based on the
TI AM335x processor. Schematics are available [2].
[1] https://store.gumstix.com/index.php/products/344/
[2] https://pubs.gumstix.com/boards/PEPPER/
Signed-off-by: Ash Charles <ash@gumstix.com>
[trini: Move 'cdev' in board.c down to under #ifdef's where it's used]
Signed-off-by: Tom Rini <trini@ti.com>
The commits
commit b7b5f1a16c
Author: Albert ARIBAUD <albert.u.boot@aribaud.net>
da850evm, da850_am18xxevm: convert to CONFIG_SPL_MAX_FOOTPRINT
and
commit e7497891e3
Author: Albert ARIBAUD <albert.u.boot@aribaud.net>
cam_enc_4xx: convert to CONFIG_SPL_MAX_FOOTPRINT
replaced CONFIG_SPL_MAX_SIZE by CONFIG_SPL_MAX_FOOTPRINT. However,
CONFIG_SPL_MAX_SIZE is used in the Makefile for padding the SPL
when preparing an u-boot.ais image. By removing CONFIG_SPL_MAX_SIZE
said commits broke the ais image of the da850evm and cam_enc_4xx
configurations.
This patch converts the u-boot.ais target to use CONFIG_SPL_PAD_TO
instead of CONFIG_SPL_MAX_SIZE for padding the SPL and adds
a #define CONFIG_SPL_PAD_TO where it is required.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Reported-by: Tom Taylor <ttaylor.tampa@gmail.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The actual board name is draco and dxr2 is the target name.
In the future we'll have different targets based on draco board.
All changes are purely non-functional and basically rename dxr2
to draco.
One style fix in board.c that existed already before.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Fall back to previous dtb used when omap3-beagle-xm-ab.dtb doesn't exist in file system
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Nishanth Menon <nm@ti.com>
Acked-by: Tom Rini <trini@ti.com>
As of v3.15-rc3, omap3-beagle-xm-ab.dtb now exists with the usb hub (ehci) enabled.
For older kernels versions, cherry pick from mainline:
ef78f3869c37c480f1d58462a760a40dabc823f4
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
In order to have the same LED indication like in another product
when ready for updating, enable only red led and disable status
LED when entering DFU mode.
The status LED is only switched off when defined in board file.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
* remove setting LED in user button function.
We want to decouple reading user button and setting LED. This
two things need to be done independently.
* led cmd can be used to control LEDs that are defined in board file
having a led cmd, one can easily set LEDs in u-boot shell. For
example bootcmd can be extended to disable status LED before
loading kernel.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
* add parameters for factory and print them at start up to
facilitate control of right DDR3 settings in EEPROM.
* cosmetic changes in a couple of printfs
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
For dxr2 board DXR2_IOCTRL_VAL is set by data in EEPROM. In pxm2
board it does not make sense to have dxr2 as prefix. Replace it with
more meaningful DDR prefix.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Pascal Bach <pascal.bach@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
