This commit fixes a serious issue occurring when several network
commands are run on a raspberry pi 4 board: for instance a "dhcp"
command and then one or several "tftp" commands. In this case,
packet recv callbacks were called several times on the same packets,
and send function was failing most of the time.
note: if the boot procedure is made of a single network
command, the issue is not visible.
The issue is related to management of the packet ring buffers
(producer / consumer) and DMA.
Each time a packet is received, the ethernet device stores it
in the buffer and increments an index called RDMA_PROD_INDEX.
Each time the driver outputs a received packet, it increments
another index called RDMA_CONS_INDEX.
Between each pair of network commands, as part of the driver
'start' function, previous code tried to reset both RDMA_CONS_INDEX
and RDMA_PROD_INDEX to 0. But RDMA_PROD_INDEX cannot be written from
driver side, thus its value was actually not updated, and only
RDMA_CONS_INDEX was reset to 0. This was resulting in a major
synchronization issue between the driver and the device. Most
visible behavior was that the driver seemed to receive again the
packets from the previous commands (e.g. DHCP response packets
"received" again when performing the first TFTP command).
This fix consists in setting RDMA_CONS_INDEX to the same
value as RDMA_PROD_INDEX, when resetting the driver.
The same kind of fix was needed on the TX side, and a few variables
had to be reset accordingly (c_index, tx_index, rx_index).
The rx_index and tx_index have only 256 entries so the bottom 8 bits
must be masked off.
Originated-by: Etienne Dublé <etienne.duble@imag.fr>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Tested-by: Petr Tesarik <ptesarik@suse.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
As the error message is now displayed by generic phy functions,
the dev_err/pr_err can be change to dev_dbg/pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As the error message is now displayed by generic phy functions,
the pr_err can be change to pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As the error message is now displayed by generic phy functions,
the pr_err can be change to pr_debug.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As the error message is now displayed by generic phy functions,
the dev_err can be change to dev_dbg.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- This patch moves sata phy powerup from dedicate phy to compphy
and adds invert option for sata powerup routine.
Change-Id: I1b4e8753e2b2c14c6efa97bca2ffc7d2553d8a90
Signed-off-by: zachary <zhangzg@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/53601
Reviewed-by: Igal Liberman <igall@marvell.com>
Tested-by: Igal Liberman <igall@marvell.com>
[a.heider: adapt to mainline]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The size returned by 'getvar partition-size' should be in bytes, not in
blocks as fastboot uses that value to generate empty partition when
running format [1].
Note that the function was already returning the proper size in bytes
for NAND devices (see struct part_info details).
[1]
https://android.googlesource.com/platform/system/core/+/refs/heads/android10-release/fastboot/fastboot.cpp#1500
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
It was revealed that when the fastboot_tx_write_str function is called
without the previously initialized fastboot_func->in_req->complete field,
a copy of in_req will be sent to the I/O requests queue without
an initialized field.
Moving a piece of code with the initializing of the
fastboot_func->in_req->complete field above transmit_tx allows to solve
this problem.
Fixes: 65c96757fe "usb: fastboot: Convert USB f_fastboot to shared fastboot"
Signed-off-by: yurii.pidhornyi <yurii.pidhornyi@globallogic.com>
Since the USB HID limits the maximum bandwidth(3072) for interrupt
endpoint transfers, when the bInterval set to 1, we can only support 3
boards to run sdp at the same time. In order to support more boards,
change the bInterval of interrupt endpoint to 3, which will not affect
the transmission speed.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
EP0 has been used to transfer file data in sdp before, but the max
packetsize of ep0 is 64 bytes. So in order to improve the file transfer
speed, here add the EP1_OUT interrupt endpoint which max packetsize is
set to 1024 byte.
After testing, it turns out that using ep1out is twice as fast as using
ep0 while receiving data in sdp.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support to f_sdp to search and load iMX8 container image or iMX8M
FIT image by new UUU command SDPV.
When using the SDPV, the uuu will continue to send out data after first
level boot loader used by ROM. This means uuu won't skip to the offset
of the second boot loader, and the padding data before second boot loader
will be sent out. So we have to search the FIT header or container header
in the buffer that SDP received.
Also change to more common method to exit f_sdp handler not depending on
SPL_FIT_FOUND flag because container loader won't set this.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Because the buffer length of sdp usb request is 65, we have to allocate
65 bytes not 64 bytes. Otherwise there is potential buffer overflow.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add HS endpoint descriptor for SDP. So that we can use high speed endpoint,
and the SDP device can send packet with 512 byte size.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
MAX3420 implements FullSpeed USB Device over SPI.
Another version MAX3421, also implements USB Host mode.
This driver should be good for the device mode of max3421 as well.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Default implementation of fastboot_set_reboot_flag function that depends
on "bcb" commands could be used in general case if there are no need to
make any platform-specific implementation, otherwise it could be
disabled via Kconfig option FASTBOOT_USE_BCB_SET_REBOOT_FLAG.
Please note that FASTBOOT_USE_BCB_SET_REBOOT_FLAG is mutually exclusive
with some platforms which already have their own implementation of this
function.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Android 10 adds support for dynamic partitions and in order to support
this userspace fastboot must be used[1]. New tool fastbootd is
included into recovery.
Userspace fastboot works from recovery and is launched if:
1) - Dynamic partitioning is enabled
2) - Boot control block has 'boot-fastboot' value into command field
The bootloader is expected to load and boot into the recovery image
upon seeing boot-fastboot in the BCB command. Recovery then parses the
BCB message and switches to fastbootd mode[2].
Please note that boot script is expected to handle 'boot-fastboot'
command in BCB and load into recovery mode.
Bootloader must support 'reboot fastboot' command which should reboot
device into userspace fastboot to accomodate those changes[3].
Another command that bootloader must support[3] is 'reboot recovery'. This
command should simply reboot device into recovery mode.
[1] - https://source.android.com/devices/bootloader/fastbootd
[2] - https://source.android.com/devices/bootloader/fastbootd#unified_fastboot_and_recovery
[3] - https://source.android.com/devices/bootloader/fastbootd#modifications_to_the_bootloader
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Change-Id: I9d2bdc9a6f6f31ea98572fe155e1cc8341e9af76
Extend fastboot_set_reboot_flag arguments with reboot reason so that
it could handle different reboot cases in future.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
The environment variable loadaddr is in the virtual address space of the
sandbox. To get the actual memory address where the FIT image has been
loaded we have to convert this address according to the memory mapping of
the sandbox.
Equally the addresses in the *.its file have to be converted when used in
the dfu_ram driver.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add support for defining raw fastboot partitions in eMMC by specifying
the offset and size in an environment variable. Optionally, the eMMC
hardware partition number may also be specified.
This makes it possible to e.g. update only part of the eMMC boot
partition, instead of having to write the entire partition.
Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
When unregister gadget driver in ci_udc, the usb device is not
removed or stop. This causes next "usb start" fails to work.
Add a new interface "usb_remove_ehci_gadget" in usb-uclass to
remove the usb device for DM driver. Using "usb_lowlevel_stop" for
non-DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The usb mass storage (f_mass_storage.c) uses fixed usb index 0,
this causes problem while CDNS3 USB controller index is 1.
Modify the API of fsg to pass the controller index.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The original rtl_clear_bp() is used to clear the firmware of both
PLA and USB MCU. The new one could clear the firmware of PLA or
USB independently. It is unnecessary to clear firmware, if there
is no one to be updated.
Besides, clear the firmware by writing the relative registers in
bulk.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reset bmu after disabling Tx/Rx. This is used to clear the FIFO of
Tx/Rx. The remained data may be transferred after Tx/Rx is re-enabled.
And it results in garbage data.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
If the SCIF is receiving data quickly enough, it may happen that the
SCxSR_RDxF flag is cleared in sh_serial_getc_generic(), while the
FIFO still contains data. If that happens, the serial_getc_check()
reports no data in the FIFO as the flag is no longer set. Add one
more check, if the SCxSR_RDxF is not set, read out the FIFO level
and if there are still characters in the FIFO, permit reading them
out.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix this typo in the Kconfig help.
Suggested-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For proper initialization of aardvark pci driver it is required to
de-assert reset GPIO. So depeneds on DM_GPIO option.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
- The SDIO signal voltage and max base clock frequency
setting are missing in driver, which causes SDIO
not working.
- The patch adds SDIO signal voltage switch support,
which is based on regulator-gpio of vqmmc-supply, and
sets the max base clock frequency.
- Fix the zero clock value in call to sdhci_setup_cfg()
function.
Change-Id: I79c8860c65b8db166f4f70db56ede4097f71f1fa
Signed-off-by: Evan Wang <xswang@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/53589
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: Hua Jing <jinghua@marvell.com>
[pali: Amended fixup patch]
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
This change ensures that PCIe card is put into reset state when U-Boot
stops using it.
DM_FLAG_OS_PREPARE ensures that U-Boot executes driver's remove callback
prior booting Linux kernel.
Linux kernel pci-aardvark driver needs to reset PCIe card via PERST# signal
prior initializing it. If it does not issue reset then some PCIe cards
(specially Compex WiFi cards) are not detected at all.
Putting PCIe card into reset state prior booting Linux kernel would ensure
that card would be properly reset at time when Linux kernel starts
initializing pci-aardvark driver.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Change active-high to active-low and change DT property name from
reset-gpio to reset-gpios. This format of gpio reset is used by
pci-aardvark driver in Linux kernel.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
With ABI 3.0, sysfw deprecated special resource types used for AM65x
SoC. Instead started using device id as resource type similar to the
convention used in J721E SOC.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There is missing dependency for PCIE_ROCKCHIP which selects
PHY_ROCKCHIP_PCIE which directly depends on ARCH_ROCKCHIP.
WARNING: unmet direct dependencies detected for PHY_ROCKCHIP_PCIE
Depends on [n]: ARCH_ROCKCHIP [=n]
Selected by [y]:
- PCIE_ROCKCHIP [=y] && PCI [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The indentation was messing up with the scripts/build-whitelist.sh that
was marking SYS_USB_EVENT_POLL_VIA_INT_QUEUE (and probably also the
other indented options) erroneously as ad-hoc configure option with the
following error:
```
Error: You must add new CONFIG options using Kconfig
The following new ad-hoc CONFIG options were detected:
CONFIG_SYS_USB_EVENT_POLL_VIA_INT_QUEUE
```
All platforms support bi_dram[] since quite some time. Lets remove the
and bi_memsize values completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 86cf1c8285 ("configs: Migrate CONFIG_NR_DRAM_BANKS") &
commit 999a772d9f ("Kconfig: Migrate CONFIG_NR_DRAM_BANKS"),
CONFIG_NR_DRAM_BANKS is always defined with a value (4 is default).
It makes no sense to still carry code that is guarded with
"#ifndef CONFIG_NR_DRAM_BANKS" (and similar). This patch removes
all these unreferenced code paths.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Add basic Marvell/Cavium OcteonTX/TX2 support (Suneel)
- Infrastructure changes to PCI uclass to support these SoC's (Suneel)
- Add PCI, MMC & watchdog driver drivers for OcteonTX/TX2 (Suneel)
- Increase CONFIG_SYS_MALLOC_F_LEN for qemu-x86 (Stefan)
- Sipeed Maix support S-mode.
- Provide command sbi.
- Use fdtdec_get_addr_size_auto_parent to get fu540 cache base address.
- Fix a compiler error with CONFIG_SPL_SMP=n.
- Fix sifive ram driver 32 compiler warnings.
- Fix kendryte/pll.h redefine nop() warning.
Adds support for Core 0 watchdog poke on OcteonTX and OcteonTX2
platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds support for MMC controllers found on OcteonTX or
OcteonTX2 SoC platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Peng Fan <peng.fan@nxp.com>
Adds support for PCI ECAM/PEM controllers found on OcteonTX
or OcteonTX2 SoC platforms.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
For SATA controller found on OcteonTX SoC's, use non-standard PCI BAR0
instead of BAR5.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add check if the referenced ofnode is valid.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
If ARI capability is found on device, use it to update next function
number in bus scan and also helps to skip unnecessary bdf scans.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Makes dm_pci_map_bar API available to map BAR for Virtual function
PCI devices which support Enhanced Allocation.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
SR-IOV - Single Root I/O Virtualization
PF - Physical Function VF - Virtual Function
If SR-IOV capability is present, use it to initialize Virtual Function
PCI device instances. pci_sriov_init function will read SR-IOV
registers to create VF devices under the PF PCI device and also bind
driver if available. This function needs to be invoked from Physical
function device driver which expects VF device support, creating
minimal impact on existing framework.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
If Enhanced Allocation capability is present in bridges, use it
to read the fixed sub-ordinate bus number.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Enable PCI memory regions in ranges property to be of multiple entry.
This helps to add support for SoC's like OcteonTX/TX2 where every
peripheral is on PCI bus.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Fix for the case of a U-Boot configuration with CONFIG_SPL,
CONFIG_I2C_MUX, CONFIG_I2C_MUX_PCA954x, no CONFIG_SPL_DM and no
CONFIG_SPL_I2C_MUX. Without this fix linking of pca954x fails because
dm_write_i2c does not exist because CONFIG_SPL_DM is not defined.
Signed-off-by: Kees Trommel <kees.trommel.contractor@draeger.com>
Cc: Heiko Schocher <hs@denx.de>
This patch fixes a few issues noticed, when testing this new driver on
ARM Octeon TX2 again. Here the details:
- Remove "common.h" header inclusion
- Use correct THP define on Octeon TX2
- Octeon TX2 uses the same compatible as Octeon TX. We can't distinguish
both platforms this way. Remove the unused "cavium,thunder2-99xx-twsi"
compatible and add a check to the Octeon TX2 specific
"cavium,thunderx-i2c" so that the correct driver data is selected.
- Removed "struct pci_device_id" definition and U_BOOT_PCI_DEVICE()
as its not needed for the PCI based probing on Octeon TX2
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Suneel Garapati <sgarapati@marvell.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Parse subnode DT properties only if parent node is valid.
Otherwise, assert is triggered on ofnode_valid in ofnode_first_subnode
from dev_for_each_subnode.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Fix argument ordering for map_physmem() called in dm_pci_map_ea_bar().
Additinally minor spelling correction.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Instead of using a fixed length pre-allocated array of regions, this
patch moves to dynamically allocating the regions based on the number
of available regions plus the necessary regions for DRAM banks.
Since MAX_PCI_REGIONS is not needed any more, its removed completely
with this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Since the migration to Kconfig, CONFIG_NR_DRAM_BANKS is configured for
all boards. Hence we can remove the conditional compilation and the code
path that will never get compiled.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
priv->info.size is of type 'size_t' but the length modifier is l.
Fix this by casting priv->info.size. Note 'z' cannot be used as
the modifier as SPL does not support that.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Pragnesh Patel <pragnesh.patel@openfive.com>
Cleaning up the following:
ERROR: do not use assignment in if condition
#281: FILE: drivers/xen/pvblock.c:260:
+ if ((err = xenbus_switch_state(XBT_NIL, nodename,
CHECK:COMPARISON_TO_NULL: Comparison to NULL could be written "err"
#52: FILE: drivers/xen/pvblock.c:298:
+ if (err != NULL) {
ERROR: do not use assignment in if condition
#176: FILE: drivers/xen/gnttab.c:103:
+ if ((flags = nflags) & (GTF_reading | GTF_writing)) {
WARNING: Missing or malformed SPDX-License-Identifier tag in line 1
#329: FILE: include/xen/gnttab.h:1:
+/*
WARNING: Misplaced SPDX-License-Identifier tag - use line 1 instead
#330: FILE: include/xen/gnttab.h:2:
+ * SPDX-License-Identifier: GPL-2.0
ERROR: do not use assignment in if condition
#630: FILE: lib/sscanf.c:558:
+ if ((n = inr) < width) {
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
after review of sam copyright should be on one line and link should
not between author lines
just remove the link and put ryder first as he is author of linux-driver
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
make the shared reg optional when version is v1 for sata
Suggested-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
'log2blksz' in blk_desc structure must always be initialized, otherwise
it will cause a lot of weird failures in file operations.
For example, fs_set_blk_dev[_with_part]() examines a block device against
every file system with its probe function. In particular, ext4 file
system's ext4_probe() will calls fs_devread() to fetch a super block.
If log2blksz is 0, the actual 'read' size, i.e. block_len >> log2blksz, is
much bigger than a buffer's size, and it can end up with memory corruption.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Fixes: f4802209e5 ("virtio: Add block driver support")
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is no reason to bind psci driver if U-Boot runs in EL3 because
SMC/HVC instructions can't be called. That's why detect this state and
don't let user to crash from prompt by performing reset or poweroff
commands (if enabled).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Add CCF clocks definitions for iMX6Q enet (ETH)
- Several fixes for CCF framework - the most notable is the one, which
adds get_rate helper to clk-mux.c
- Improvements for clk command - better visibility and alignment.
After adding custom get_rate helper function it was necessary to include
<dm/uclass.h> to avoid warnings about missing uclass_get_device_by_name.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Series-to: u-boot
The previous version of the get_rate helper does not work if the mux
clock parent is changed after the probe. This error has not been
detected because this condition has not been tested. The error occurs
because the set_parent helper does not change the parent of the clock
device but only the clock selection register. Since changing the parent
of a probed device can be tricky, the new version of the get_rate helper
provides the rate of the selected clock and not that of the parent.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The tests developed for the mux clock are run on the sandbox. They don't
call the clk_mux_set_parent routine and therefore they do not detect
this error.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The parent->name variable can be used only in case the
uclass_get_device_by_name routine returns successfully.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The top-level framework flags are passed as parameter to the common
clock framework (ccf) registration routines without being used.
Checks of the flags setting added by the patch have been added in the
ccf test.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Unlike the other clock types, in the case of the gated clock, a new
driver has been developed which does not use the registering routine
provided by the common clock framework.
The addition of the ecspi0 clock to sandbox therefore allows testing
the ccf gate clock.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
After commit 673f659732 ("net: fec_mxc: support i.MX8M with CLK_CCF") all
NXP boards, which are not IMX8 and in the same time are supporting CCF need
to provide PTP clock.
On the i.MX6Q this clock is provided with IMX6QDL_CLK_ENET_REF in the Linux
kernel's CCF.
Code in this change models the simplest case when enet reference clock is
generated from 'osc' clock.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This code has been ported from Linux kernel v5.5.5 (tag) and has been
adjusted to U-Boot's DM.
It adds support for correct recognition of IMX_PLLV3_ENET flag in the
clk-pllv3.c driver.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After commit 673f659732 ("net: fec_mxc: support i.MX8M with CLK_CCF") all
NXP boards, which are not IMX8 and in the same time are supporting CCF
need to provide IMX6QDL_CLK_ENET.
This change defines the missing clock in i.MX6Q's CCF.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Do not calculate a unused value of n which is overwritten in both branches
of the subsequent if statement.
Identified by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
binman fixes for portage
various minor fixes
'bind' command improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl9BbZcRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZZiQf/UVsriftmxdDz3Lvbz7Jw6UCBXbeM3UN8
KgRxVll3kurZeu8bIcjAPY4YRrbWRqSXmZTXpZWgbyZzHLM4RnkamY3KF3DoxPjc
cbskd/fr4nPjSZVFrkzrvD+D5bhm+VrMtf861AkbAqqpG+Q1FmWHgApqOL1fXn3s
2VoMxRz8Cn9KkSDmxaCtJnLX77GVYYdfgii7RuNWGDqr3eBWrzflV38VbPHLplEg
VLqaLBe3G4zVwElA9Nc2hXpZB84KZEETHcBnmCzNkrSYTN2ofvSeZrWbtRztQFhz
yKur1y7jFsryRkMfxBzgldsKFRNnPT9vr+0qGtrztHjCmvhDkx1YMg==
=iDRJ
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-22aug20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
replace devfdt_get_addr_ptr() with dev_read_addr_ptr()
binman fixes for portage
various minor fixes
'bind' command improvements
This converts the following to Kconfig:
CONFIG_SPLASH_SCREEN
CONFIG_SPLASH_SCREEN_ALIGN
CONFIG_SPLASHIMAGE_GUARD
CONFIG_SPLASH_SOURCE
Signed-off-by: Simon Glass <sjg@chromium.org>
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To help this tedious work, this commit converts devfdt_get_addr_ptr()
to dev_read_addr_ptr() by coccinelle. I also removed redundant casts
because dev_read_addr_ptr() returns an opaque pointer.
To generate this commit, I ran the following semantic patch
excluding include/dm/.
<smpl>
@@
type T;
expression dev;
@@
-(T *)devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
@@
expression dev;
@@
-devfdt_get_addr_ptr(dev)
+dev_read_addr_ptr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is strange to use devfdt_get_addr_ptr(), then cast the pointer
back to ulong because you could use devfdt_get_addr() without casting.
Convert it to dev_read_addr(), which is capable to CONFIG_OF_LIVE.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
It is strange to use devfdt_get_addr_ptr(), then cast the pointer
back to uint32 because you could use devfdt_get_addr() without casting.
Convert it to dev_read_addr(), which is capable to CONFIG_OF_LIVE.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
According to the description of devfdt_get_addr_ptr, this function should
return NULL on failure, but currently it returns (void *)FDT_ADDR_T_NONE.
Fix this by making devfdt_get_addr_ptr return NULL on failure, as
described in the function comments. Also, update the drivers currently
checking (void *)FDT_ADDR_T_NONE to check for NULL.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver data to existing compatible string "sandbox,phy".
Add an additional compatible string without driver_data
This will verify that bind command parses, finds and passes the
correct driver data to device_bind_with_driver_data() by using
driver_data in the second sandbox_phy_ids table entry.
In sandbox_phy_bind() a check is added to validate driver_data
content.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the case of the live tree ofnode_read_addr_cells() and
ofnode_read_size_cells() return the #address-cells and #size-cells defined
in the parent node. With the patch the same is done for a non-live tree.
The only consumer of these functions is currently the CFI flash driver.
This patch fixes the incorrect parsing of the device tree leading to
'saveenv' failing on qemu_arm64_defconfig.
For testing qemu-system-aarch64 has to be called with
-drive if=pflash,format=raw,index=1,file=envstore.img
to provide the flash memory. envstore.img must be 64 MiB large.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no reason to have firmware specific structure in clock driver.
Move it to generic location and also initialize enum values which is based
on https://lore.kernel.org/linux-arm-kernel/20200318125003.GA2727094@kroah.com/
recommended way to go to make sure that values guaranteed by compiler.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Instead of recasting and shifting use macros which are designed for taking
upper/lower 32bit value from 64bit variable.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The capabilities register has a field to indicate whether the host
supports high speed mode or not. Add high speed host_caps based on
this bit instead of enabling it by default.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Michal Simek <michal.simek@xilnx.com>
Tested-by: Michal Simek <michal.simek@xilnx.com>
(zcu104 with sdhci-caps-mask = <0 0x200000>;)
Current IPI module register description is not align with IPI HW. The
registers with the wrong offset are not used so it does not cause real
issues. This patch aligns the register description.
Additionally comments added to explain why recv function does not check
any flag prior copying rx data.
Fixes: 660b0c77d8 ("mailbox: zynqmp: ipi mailbox driver")
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch merges ZynqMP firmware calls under xilinx_pm_request in order
to make trainsparent the EL. Calls at EL3 are send through IPI messages
and EL2 through SMC calls.
The EL2 call uses fixed payload and arg size as the EL3 call. The
firmware is capable to handle PMUFW_PAYLOAD_ARG_CNT bytes but the
firmware API is limited by the SMC call size.
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removes duplicated definition of PAYLOAD_ARG_CNT and define it in the
firmware driver. Additionally fixes payload buffer declarations without
macro usage
Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DT binding is saying that default value is 0 not -1 that's why fix it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
s/xlnx,mio_bank/xlnx,mio-bank/g
DT binding is describing mio-bank not mio_bank that's why fix all DTSes and
also driver itself.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Remove adhoc dt binding for fixed-partition definition for i2c eeprom.
fixed-partition are using reg property instead of offset/size pair.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Zynq/ZynqMP/Versal IPs should be possible to called also from Microblaze in
PL and vice versa. That's why change dependencies and do not limit enabling
just for some platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
add support for PHY_TYPE_SATA to Mediateks TPHY driver
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
This patch adds PCIe support for the Mediatek MT7622 SOC.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
This patch adds pciesys support in clock driver for
MediaTek MT7622 SoC.
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Free resources used by Xen board before jumping to Linux kernel.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement Xen para-virtual frontend to backend communication
and actually read/write disk data.
This is based on mini-os implementation of the para-virtual block
frontend driver.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Read essential virtual block device configuration data from XenStore,
initialize front ring and event channel.
Update block device description with actual block size.
Use code for XenStore from mini-os.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Add initial infrastructure for Xen para-virtualized block device.
This includes compile-time configuration and the skeleton for
the future driver implementation.
Add new class UCLASS_PVBLOCK which is going to be a parent for
virtual block devices.
Add new interface type IF_TYPE_PVBLOCK.
Implement basic driver setup by reading XenStore configuration.
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Make required updates to run on u-boot.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Make required updates to run on u-boot and strip test code.
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Add wait_event_timeout - sleep until a condition gets true or a
timeout elapses.
This is a stripped version of the same from Linux kernel with the
following u-boot specific modifications:
- no wait queues supported
- use u-boot timer to detect timeouts
- check for Ctrl-C pressed during wait
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
[trini: Drop atomic_read from gadget/ether.c as this has existed for a
while and now causes problems]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for Xen para-virtualized serial driver. This
driver fully supports serial console for the virtual machine.
Please note that as the driver is initialized late, so no banner
nor memory size is visible.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make required updates to run on u-boot. Strip functionality
not needed by U-boot.
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Port hypervisor related code from Mini-OS. This is referencing the code
of Mini-OS from [1] by Huang Shijie and Volodymyr Babchuk which is for
ARM64.
Update essential arch code to support required bit operations, memory
barriers etc.
Copyright for the bits ported belong to at least the following authors,
please see related files for details:
Copyright (c) 2002-2003, K A Fraser
Copyright (c) 2005, Grzegorz Milos, gm281@cam.ac.uk,Intel Research Cambridge
Copyright (c) 2014, Karim Allah Ahmed <karim.allah.ahmed@gmail.com>
[1] - https://github.com/zyzii/mini-os.git
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
[trini: Drop wmb() from musb-net/linux-compat.h now]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
-----BEGIN PGP SIGNATURE-----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=J4aq
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200813' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Use IS_ENABLED to prevent ifdef in board_key_check for STM32MP
- Add STM32 FMC2 EBI controller driver
- Fix dwc3-sti-glue which allows STiH410-B2260 to boot again
- Add fitImage its entry for 587-200 DHCOR SoM
- Add both PDK2 and DRC02 DT into DHCOM fitImage its
- Fix DHCOM KS8851 ethernet MAC address
- Remove stm32mp1 board.c file
- Use const for struct node_info in board stm32mp1.c file
FMC2 EBI support has been added. Common resources (registers base
address and clock) can now be shared between the 2 drivers using
"st,stm32mp1-fmc2-nfc" compatible string. It means that the
common resources should now be found in the parent device when EBI
node is available.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The driver adds the support for the STMicroelectronics FMC2 EBI controller
found on STM32MP SOCs.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This patch renames functions and local variables.
This cleanup is done to get all functions starting by stm32_fmc2_nfc
in the FMC2 raw NAND driver when all functions will start by
stm32_fmc2_ebi in the FMC2 EBI driver.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
FMC2_TIMEOUT_5S will be used each time that we need to wait.
It was seen, during stress tests in an overloaded system,
that we could be close to 1 second, even if we never met this
value. To be safe, FMC2_TIMEOUT_MS is set to 5 seconds.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove inline comments that are useless since function label are
self explanatory.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The chip select defined in the device tree could only be 0 or 1.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
node varaible is used as iterator into ofnode_for_each_subnode()
loop, when exiting of it, node is no more a valid ofnode.
Use dwc3_node instead as parameter of ofnode_valid()
Fixes: ac28e59a57 ("usb: Migrate to support live DT for some driver")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Add device identification for J7200 SoC
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
k3-j721e ddr driver sanity checks for product id and version number.
Version number gets changed for every minor update in the IP. So discard
the version check and just sanity check for product id.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The hardcoded array size leads to array overflows with changes in
speed modes enum in mmc core. Use MMC_MODES_END for otap_del_sel
array declaration to fix this.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This is based on the Linux kernel driver for the RTI watchdog.
To actually reset the system on an AM65x, it requires firmware running
on the R5 that accepts the NMI and issues the actual system reset via
TISCI. Kind of an iTCO, except that this watchdog hardware has support
for no-way-out, and only for that.
On the J721E, reset works without extra firmware help when routing the
RTI interrupt via the ESM.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add Cortina Access LED controller support for CAxxxx SOCs
Signed-off-by: Jway Lin <jway.lin@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Simon Glass <sjg@chromium.org>
Add head file fixed link error and remove unused flashing function
Reviewed-by: Simon Glass <sjg@chromium.org>
Extend manual relocation of block_cache list pointers to all platforms that
enable CONFIG_NEEDS_MANUAL_RELOC. Remove m68k-specific checks and provide a
single implementation that adds gd->reloc_off to the pre-relocation
pointers.
Acked-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Tested-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
[trini: Add guard around DECLARE_GLOBAL_DATA_PTR to avoid size growth]
Signed-off-by: Tom Rini <trini@konsulko.com>
serial_initialize is called only during the common init sequence, after
relocation (in common/board_r.c). Because it has a void return value, it
has to wrapped in initr_serial. In order to be able to get rid of this
indirection, make serial_initialize return int.
Remove extern from prototype in order to silence the following checkpatch
warning:
check: extern prototypes should be avoided in .h files
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Use IS_ENABLED() instead of #ifdef in blk_post_probe function.
No functional change intended.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
[trini: Fix thinko and use CONFIG_HAVE_BLOCK_DEVICE in IS_ENABLED()]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some platforms, like MIPS Octeon, use mapped addresses (virtual address
!= physical address). On these platforms we need to make sure, that the
local virtual addresses are converted to physical (DMA) addresses for
the xHCI controller. This patch adds the missing virt_to_phys() calls,
so that the correct addresses are used.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
These values are already swapped to CPU endianess, so swapping them
again is a bug. Let's remove the swap here instead.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
xhci_writeq() makes the CPU->LE swapping only when addressing registers
in the xHCI controller address range and not in the local memory (RAM).
We need to use cpu_to_le64() here to ensure that the conversion is done
correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
While trying to use the U-Boot xHCI driver on the MIPS Octeon platform,
which is big endian, I noticed that the driver is missing a few endian
conversion calls. This patch adds these missing endian conversion
calls.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Add configuration flag to select the supported dwc driver configuration:
- CONFIG_DWC_ETH_QOS_TEGRA186
- CONFIG_DWC_ETH_QOS_IMX
- CONFIG_DWC_ETH_QOS_STM32
See Linux driver ethernet/stmicro/stmmac and associated glue layers
for other configuration examples.
This patch removes the not-selected compatibles and lets the linker remove
the unused functions to reduce the size of the driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Move the variable psci_method in .data section when EFI is not
activated and the psci driver safely access it before relocation.
Without this patch the variable is located in .bss section
and the psci probe requested before relocation corrupts the device
tree (probe is requested by board_f.c::print_resetinfo()).
When EFI_LOADER is activated, this variable in already located in the
.data.efi_runtime section by __efi_runtime_data.
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
