The eeprom_i2c_bus is not used outside of this file, make it static.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This adds the PCA9546 4-channel i2c bus switch.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
This commit adds the command ubi rename to rename an ubi volume.
The format of the command is: ubi rename <oldname> <newname>.
To enable this command, the option CMD_UBI_RENAME must be selected.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
JTAG ID register is defined by IEEE 1149.1 for device identification.
Use this JTAG ID register for identifying AM65x[0] and J721E[1] devices
instead of using SoC specific registers.
[0] http://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
[1] http://www.ti.com/lit/ug/spruil1a/spruil1a.pdf
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
After the
commit 4213609cc7 ("drivers: core: use strcmp when find device by name")
the exact DTS node name for PMIC device must be provided.
This patch fixes this issue by providing full DTS node name ('mc34708@8').
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chug <jh80.chung@samsung.com>
The CONFIG_PHY_FIXED is necessary to allow DSA switch work in U-Boot after
the
commit 3bf135b6c3 ("drivers: net: phy: Ignore PHY ID 0 during PHY probing").
This particular device - LAN9303 - returns phy_id == 0. With
CONFIG_PHY_FIXED enabled HSC and DDC boards work again with the same U-Boot
binary.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Those two boards are supposed to be run with a single u-boot binary.
There are notable differences though - HSC uses DSA switch (which
phy_id == 0x0) and DCC (DP83848C).
After the commit 3bf135b6c3
("drivers: net: phy: Ignore PHY ID 0 during PHY probing") the PHY devices
with phy_id == 0 are not created in U-Boot anymore. This caused regression
on HSC.
To fix this problem - the fec's 'fixed-link' node has been introduced and
the phy_id is not assessed anymore. This approach works on both boards.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
During the conversion of this board to DM_REGULATOR, usb-mass-storage
was broken and started failing with the following error:
=> ums 0 mmc 2
UMS: LUN 0, dev 2, hwpart 0, sector 0x0, count 0xe90000
Error enabling VBUS supply
g_dnl_register: failed!, error: -38
g_dnl_register failed
Fix this by adding the relevant GPIO to the regulator node.
Fixes: 4ca99fe81a ("ARM: imx: dh-imx6: Enable DM regulator")
Signed-off-by: Harald Seiler <hws@denx.de>
Use DM_ETH instead of legacy networking. Add VIO as a fixed regulator
to the relevant device-trees and augment the FEC node with properties
for the reset GPIO.
It should be noted that the relevant properties for the reset GPIO
already exist in the PHY node (reset-gpios, reset-delay-us,
reset-post-delay-us) but U-Boot currently ignores those and only
supports the bus-level reset properties in the FEC node
(phy-reset-gpios, phy-reset-duration, phy-reset-post-delay).
Signed-off-by: Harald Seiler <hws@denx.de>
Since CONFIG_DISPLAY_BOARDINFO_LATE is no longer used, the checkboard()
function is no longer called.
As it is useful to print the board revision, print it inside
board_late_init() instead.
Also, to avoid GPIO errors related to using a GPIO without requesting it,
move the gpio_request(REV_DETECTION, "REV_DETECT") call prior to its
usage.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
Since we are using revD1 device tree for all board revisions, the
following can be seen on a revB1 board:
Model: Wandboard i.MX6 Quad Board revD1
Board: Wandboard rev B1
To avoid such confusing messages, disable CONFIG_DISPLAY_BOARDINFO_LATE.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
On wandboard variants prior to revD1, there is no PMIC populated, so
do not print an error when the reading of the device ID register fails.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
In some cases U-Boot runs the same binary on different board versions.
In wandboard, for example, there are versions with the PFUZE100 PMIC
populated and others without it.
When the PMIC is not present, it is not really useful to get PMIC error,
so change the error message level to debug instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
The detection of the revD1 version is based on the presence of the PMIC.
Currently revb1 device trees are used for mx6q/mx6dl variants, which
do not have the PMIC nodes.
This causes revD1 boards to be incorrectly be detected as revB1.
Fix this issue by using the revd1 device trees, so that the PMIC node can be
found and then the PMIC can be detected by reading its register ID.
Imported the revd1 device trees from mainline kernel version 5.7-rc1.
Reported-by: Heiko Schocher <hs@denx.de>
Reported-by: Derek Atkins <derek@ihtfp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Derek Atkins <derek@ihtfp.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
mxsfb needs a dcache function not implemented in cortex-M7, so for the
moment let's keep dcache not enabled.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Enable DM_VIDEO subsystem and its BACKLIGHT_GPIO. Then enable
SYS_WHITE_ON_BLACK to have classic black background on display. Need
also to enable CONFIG_SYS_CONSOLE_ENV_OVERWRITE to retrieve
stdin/stdout/stderr from CONFIG_EXTRA_ENV_SETTINGS.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Linux doesn't provide skeleton.dtsi file so let's remove its include and
provide #address-cells/size-cells = <1> that were defined in
skeleton.dtsi before.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
i.MXRT1050 provides mxsfb compatible lcd controller, so let's enable
video mxsfb driver with 16bpp depth if CONFIG_DM_VIDEO is selected since
board has 16bpp only connection.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
ENABLE signal can now be flipped by writing its bitmask on vdctrl0
register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
DOTCLK signal can now be flipped by writing its bitmask on vdctrl0
register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
VSYNC signal can now be flipped by writing its bitmask on vdctrl0
register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
HSYNC signal can now be flipped according to display_flags bitmaks by
writing its bitmask on vdctrl0 register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
struct display_timings provides more informations such clock and DE
polarity, so let's refactor the code to use struct display_timings
instead of struct ctfb_res_modes, so we'll become able to get clock and
DE polarity settings and set register according to them in the next patch.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add support for i.MXRT by adding CONFIG_IMXRT in register structure and
adding .compatible = "fsl,imxrt-lcdif".
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Allow using DM CLK instead of mxs_set_lcdclk() so we can avoid to
implement a special function to set lcd clock on i.MXRT.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Since video_ctfb_mode_to_display_timing() has been implemented by moving
sunxi_ctfb_mode_to_display_timing() to video_modes.c and it's meant to be
used by other video subsystem, let's use it instead of local
sunxi_ctfb_mode_to_display_timing().
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This function converts from "struct ctf_res_modes" to
"struct display_timing".
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Need to add set_parent() callback to allow dts assigned-clock-parents to
work so let's add it accordingly.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
mxsfb needs PLL5 as source, so let's setup it at its default frequency
specified in RM(650Mhz).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
"video:" must be "video", ":" is a typo.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
pllv3 PLLs have powerdown/up bits but enable bits too. Specifically
"enable bit" enable the pll output, so when dis/enabling pll by
setting/clearing power_bit we must also set/clear enable_bit.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Remove 'fdt_high' and 'initrd_high' environment variables (set to 0xFFFFFFFF)
from default environment which prevents relocation of FDT and initrd.
Rely on 'bootm_size' value instead to safely relocate kernel, device tree and
initrd.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add nfsboot wrapper to env to boot Linux kernel from TFTP/NFS.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Adjust DRAM size in case BL32 secure payload is loaded (OP-TEE/Trusty),
so during MMU initialization U-Boot won't touch this mem area.
BL32 is loaded to the end of DRAM, bl32 payload size is read from
rom_pointer[1]. This relates to the issue described in
59efa6b52b("imx8m: Fix MMU table issue for OPTEE memory").
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Adjust DRAM size in case BL32 secure payload is loaded (OP-TEE/Trusty),
so during MMU initialization U-Boot won't touch this mem area.
BL32 is loaded to the end of DRAM, bl32 payload size is read from
rom_pointer[1]. This relates to the issue described in
59efa6b52b("imx8m: Fix MMU table issue for OPTEE memory").
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
After triggering a "reboot" command in Linux the following
hang in SPL is observed:
U-Boot SPL 2020.04 (Apr 15 2020 - 10:49:29 -0300)
Normal Boot
WDT: Not found!
Trying to boot from MMC2_2
spl: mmc init failed with error: -70
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This error happens because the CMD_ERR bit is set in the IRQ status
register after booting from Linux.
To ensure a fresh start, force the VMMC supply to get unpowered first.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ethernet, usdhc2 and i2c1 interfaces are probed by dm drivers.
Therefor init functions in board file are not necessary.
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
Keep code for non-dm configuration of baseboard WRU4.
It cannot be upgraded to device model as
we have no suitable device tree for it.
These changes were not run-tested on WRU4,
only compile-tested.
Signed-off-by: Michael Krummsdorf <michael.krummsdorf@ew.tq-group.com>
