Add support for specified ECC strength/size using device tree
properties nand-ecc-strength/nand-ecc-step-size.
This aligns behavior with the mainline driver, such that:
- If fsl,use-minimal-ecc is requested it will use data from
data sheet/ONFI. If this is not available the driver will fail.
- If nand-ecc-strength/nand-ecc-step-size are specified those
value will be used.
- By default maximum possible ECC strength is used
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Support driver data from device tree. Also support fsl,use-minimal-ecc
similar to Linux' GPMI NAND driver.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
In preparation for device tree support separate board init
from controller init similar to other raw NAND drivers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This function initializes DMA descriptors so mxs_nand_init_dma is
more precise. It also frees up the rather generic name mxs_nand_init.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Move GPMI and BCH register structs to the driver struct mxs_nand_info
in prepartion for device tree support.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Add support for minimum ECC strength supported by the NAND chip.
This aligns with the behavior when using the fsl,use-minimum-ecc
device tree property in Linux.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Report correct ECC parameters back to the stack. Do not report
bytes as we have it not immeaditly available and the Linux version
also does not report it. It seems to have no aversive effect.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Calculate BCH geometry at start and store the information in
a structure. This avoids recalculation on every page access
and allows to calculate ECC relevant information in one place.
This patch does not change ECC layout or driver behavior in
any way.
The patch aligns the driver somewhat with the Linux GPMI NAND
driver which drives the same IP.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Add config option which allows to enable on flash bad block table
support. This has the same effect as when using the device tree
property "nand-on-flash-bbt" in Linux.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Instead of completing initialization via scan_bbt callback use
NAND self init to initialize the GPMI (MXS) NAND controller.
Suggested-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
In preparation to convert the driver to use NAND self init
provide a new minimal init for SPL builds. As a side effect
this also reduces size of SPL by about 4KiB.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
commit 8480792287
("spi: omap3: Skip set_mode, set_speed from claim") did break SPI
support on my AM335x board.
The named commit:
- ignored the responsible arguments (speed, mode)
The set speed/mode function must use the supplied function arguments to
work properly. With this commit we take those arguments and transfer
them to the priv-data.
- used wrong udevice pointer for getting priv data
the udevice-pointer within function argument is already the spi-bus
device, so it is wrong looking here for some parent (ocp-bus in this
case) and getting priv-pointer from there.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Otherwise the frequency is zero and the clock divider cannot be setup by
'omap3_spi_set_speed' function.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
CS GPIO activation low/high is determinated by the device tree
so we don't need to take in accoung in cs_activate and cs_deactivate
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch replaced "return 0" with "return status" to fix the
incorrect return value error reported by the coverity.
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Each entry of the EFI memory descriptors occupies map->desc_size,
not sizeof(struct efi_mem_desc).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present in dram_init_banksize() it ignores conventional memory
above 4GB. This leads to wrong DRAM size is printed during boot.
Remove such limitation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable PRE_CONSOLE_BUFFER so that the full boot output can be viewed
on the video console for the EFI payload.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The use_uart assignment should follow immediately after the call to
exit_boot_services(), in case we want some debug output after that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit bb0bb91cf0 ("efi_stub: Use efi_uintn_t"), EFI x86
64-bit payload does not work anymore. The call to GetMemoryMap()
in efi_stub.c fails with return code EFI_INVALID_PARAMETER. Since
the payload itself is still 32-bit U-Boot, efi_uintn_t gets wrongly
interpreted as int, but it should actually be long in a 64-bit EFI
environment.
This changes the x86 __kernel_size_t conditionals to use compiler
provided defines instead. That way we always adhere to the build
environment we're in and the definitions adjust automatically.
Fixes: bb0bb91cf0 ("efi_stub: Use efi_uintn_t")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently efi.h determines a few bits of its environment according to
config options. This falls apart with the efi stub support which may
result in efi.h getting pulled into the stub as well as real U-Boot
code. In that case, one may be 32bit while the other one is 64bit.
This patch changes the conditionals to use compiler provided defines
instead. That way we always adhere to the build environment we're in
and the definitions adjust automatically.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: added some comments to describe the __x86_64__ check]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For boards that don't route serial port pins out, it's quite common
to attach a USB keyboard as the input device, along with a monitor.
However USB is not automatically started in the generic efi payload
codes. This uses a payload specific last_stage_init() to start the
USB bus, so that a USB keyboard can be used on the U-Boot shell.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The generic efi payload currently does not enumerate the PCI bus,
which means peripherals on the PCI bus are not discovered by their
drivers. This uses board_early_init_r() to do the PCI enumeration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With driver model philosophy, we should avoid explicitly calling
driver initialization routine during boot. This updates the ram
init sequence table to exclude the IDE initialization for DM BLK.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The default vesa mode was changed since commit 55b4e1b7d9
("x86: Change default FRAMEBUFFER_VESA_MODE of some boards") for
better VxWorks compatibility but with the changes QEMU video console
no longer works. This is because QEMU's vgabios implements the VESA
mode 8:8:8 as 24bpp without an alpha channel, which U-Boot's video
console driver currently does not support yet.
We need change to real 32bpp in order to make it work again. QEMU
vgabios implements the custom 32bpp VESA mode starting from 0x140
(320x200x32) to 0x147 (1600x1200x32). Set it to 0x144 (1024x768x32).
Fixes: 55b4e1b7d9 ("x86: Change default FRAMEBUFFER_VESA_MODE of some boards")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
car.o can only be used with start.o, not with start64.o.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Previous rename of efi-x86 target missed the MAINTAINERS update,
which caused the buildman warnings:
WARNING: no status info for 'efi-x86_app'
WARNING: no maintainers for 'efi-x86_app'
This updates the board MAINTAINERS to reflect the up-to-date info.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some environments require providing the '--smtp-server' argument to
'git send-email'. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test to exercise the check for a valid SPDX license.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Many mailing-lists consider a long Cc list a sign of spam and will
either drop the message or mark it for moderation. Because patman
automatically invokes get_maintainer.pl the Cc list can expand
unexpectedly. Allow the user to specify a limit for the Cc list.
This limit is applied after removing any known bouncing addresses. By
default no limit is applied.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that the clock-frequency information has been moved to the
driver, more DT sync is possible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In Linux, the clock rate of the UART is given by the clock driver.
If you try to follow that in U-Boot, you would end up with adding
more u-boot,dm-pre-reloc properties, and also the clock driver would
be too big for SPL, which is used for UniPhier ARMv7 platform.
The current solution is to add 'clock-frequency' property to the
UART nodes, but it does not exist in the DT files in Linux. I do
not want to let DT diverge for U-Boot.
Check the SoC compatible and set the clock rate according to it.
This will be helpful to sync DT between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable the on-chip ethernet driver for uniphier_{v7,v8}_defconfig.
Disable the on-board SMC911x because it has not migrated to the
driver model yet - it is not possible to enable DM and non-DM
drivers at the same time.
The CONFIG_SMC911X for uniphier_ld4_sld8_defconfig is still kept
because the on-chip ethernet driver for LD4, sLD8 is not supported
yet.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
A single urgent fix to make sure green and red are not swapped
in OSs that make use of EFI GOP frame buffers to display pictures
(such as efifb in Linux).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJbK8MMAAoJECszeR4D/txgqZQQAIpDTRQkWrrmiWh+h08pGMVp
k38tx84O+iToYnpQA4zH5g0QrbpzgOtvVjQJ39QTxn5p+tPYSmXkUTS5jtxppu+o
LszVHP+reQfHlL+1aV2TMsf5e1V+uoNkG3ZEJXfHxjz6VYu1vYw2psAD23vKH0PO
yOL6o5unJWYdIocNbniGwWKNYyVbiVHcBN2ErHLMRvLKeTXTJr4OZKt98sSO60Pb
p/z9sO1o1Wgwm/aiV1cD91cAItaVZD/m9cFoqOwnbwjDEM6dlRFsEhy0JLTnH/MQ
qH9wIy1W9EdON3arjfvcDejRUlX3+7uf113GyWsHPzN/p7Lm9M02UlqT5jk8njf8
TD9k5QMW6rxDsO4Pu2+zHwU38kaMLv5htJNWrcj2fOm1GDo1q0sRlTp7v6r9I5BH
KwkR69ZPDPnDj+9ApWkYVRbTzhzu+OoUbVnbB/WYTY4j0jxkW8jEh1e1yIrqlmUA
sxjPLhbWFn+PpwDzIZzLIqdSJsxX7jzqzGtmAxsmqquAqKNu3KJUn6PTJ1cLhxbD
I7qH/gHzWBLHCv/nL+/oMin9AC6UYep2zcsJMXfiTIrFSTjuWGvq4wy/WGaZG4mQ
IyrsuZ9YXDobmiV+5mNxMCvUJs31z+g20EG0+1In3C1DTpjj77t/qS4ZzKbaPwYL
DhgNUrdvlKtdMYpbWbEs
=MrHq
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-2018.07' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-06-21
A single urgent fix to make sure green and red are not swapped
in OSs that make use of EFI GOP frame buffers to display pictures
(such as efifb in Linux).
We store pixels as BGRA in memory, as can be seen from struct efi_gop_pixel.
So we need to expose the same format to UEFI payloads to actually have them
use the correct colors.
Reported-by: Fabian Vogt <fvogt@suse.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
As many targets are now commonly built with gcc-6 or later (which
defaults to a newer C standard than older compilers), certain C
constructs are now being used as they produce more readable code. And
while all compilers that we support building with support the C11
standard (and GNU11) they do not default to that standard. Ensure that
we pass along -std=gnu11 when building.
Signed-off-by: Tom Rini <trini@konsulko.com>
