Add a driver so the clocks/resets for these peripherals (especially I2C,
RSB, and UART) can be enabled using the normal uclass methods.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently, the I2C clocks are configured in the sunxi board code. Add
the I2C clocks to the DM clock driver so they can be enabled from the
DM I2C driver using the normal uclass methods.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The CCU header is only used by the DM drivers, not any platform code.
Its current location adds an artificial dependency on CONFIG_ARM and
ARCH_SUNXI, which will be problematic when adding the CCU driver for
a RISC-V sunxi platform.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In some cases, the best config cannot be used because the VCO would be
out-of-spec. In these cases, we may need to try a worse combination of r/od
in order to find the best representable config. This also adds a few test
cases to catch this and other (possible) unlikely errors.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Everything here sits in a while (true) loop. However, this introduces a
couple of layers of indentation. We can simplify the code by introducing a
single goto instead of using continue/break. This will also make adding
loops in the next patch easier.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The PLL functions take ulong arguments for rate, but still check if that
rate is negative (which is never true). The correct way to handle this is
to use IS_ERR_VALUE (like is already done in k210_clk_set_rate). While
we're at it, we can move the error checking up into the caller of the pll
set/get rate functions. This also protects our other calculations from
using bogus values for rate.
Fixes: 609bd60b94 ("clk: k210: Rewrite to remove CCF")
Reported-by: Coverity Scan <scan-admin@coverity.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYVWWZgAKCRDKSWXLKUoM
IY3MAJ43Mlut5tK9gv45bp4HpyVOMuSvJwCfTiVr7ZxrBE8I8QC5+zHzBTmuM6g=
=aQtT
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.01-rc1
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
Clocks should be enabled or disabled only if they are of GATE type
clocks. If they are not of GATE type clocks, don't touch them.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/1632808827-6109-1-git-send-email-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmFR2fMRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaAnAf/ZKPy3CRphbgAmbLhNQhQGpLosLcFp343
cv53gfsv1DakLRrhqMSnOQSVoTg9P22uHbooDDR9WHfZyEL6tvGZ+dgN2/wlDhDj
wbvvsM7FB+uvLVfMF3MURQBvy4dPO+FyCm/uHmry2V2uqWPw4ss+aVhxeQ5s4/oI
LpS6yaiM8UAj2GTUZSqJ1+/W7YG9N6tL73n0PDyCvSrdCkyPWqpww1rtST88SfFI
bBEWc6ksna/29haOwHQ2xopEbVxtHv2byULfqUtnsbtE4Ozw8o0fx66tdwPHTQlM
7eSuRiEbqjlJuUZFIbMat7nb7inZkaWupZ/Sr1HUUiDdKMygrRsQhg==
=x8Uf
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-next-27sep21' of https://source.denx.de/u-boot/custodians/u-boot-dm into next
Various of-platdata improvements, including CONFIG_OF_REAL
This is actually a misnomer now, since the phandle info may contain
a driver_info index or a udevice index. Rename it to use the word
'phandle', which seems more accurate. Add a comment while we are here.
Also add a test for this function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert some of these occurences to C code, where it is easy to do. This
should help encourage this approach to be used in new code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we have a 'positive' Kconfig option, use this instead of the
negative one, which is harder to understand.
Signed-off-by: Simon Glass <sjg@chromium.org>
Split master clock in 2 controlling block: one for prescaler one for
divider. This will allow referencing correctly the CPU clock and
master clock in device trees.
Reported-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: a64862284f ("clk: at91: sam9x60: add support compatible with
CCF")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
The K3 SoCs have some PLL output clocks (POSTDIV clocks) which in
turn serve as inputs to other HSDIV output clocks. These clocks use
the actual value to compute the divider clock rate, and need to be
registered with the CLK_DIVIDER_ONE_BASED flags. The current k3-clk
driver and data lacks the infrastructure to pass in divider flags.
Update the driver and data to account for these divider flags.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
There are three different divider values in the DIV_CTRL register
controlled by the k3-pll driver. Currently the ti_pll_clk_set_rate
function writes the entire register when programming plld, even though
plld only resides in the lower 6 bits.
Change the plld programming to read-modify-write to only affect the
relevant bits for plld and to preserve the other two divider values
present in the upper 16 bits, otherwise they will always get set to zero
when programming plld.
Fixes: 0aa2930ca1 ("clk: add support for TI K3 SoC PLL")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add the support of the BSEC clock used by the STM32MP misc driver
since the commit 622c956cad ("stm32mp: bsec: manage clock when present
in device tree") even if this clock is not yet defined in kernel device
tree stm32mp151.dtsi.
This patch avoids issue for basic boot when this secure clock are not
provided by secure world with SCMI.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Make px30 SFC clock configurable
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the missing SPI clock even if these instances are not available
on STMicroelectronics boards: SPI2_K, SPI3_K, SPI4_K, SPI6_K.
With this patch, the SPI2 / SPI3 / SPI4 / SPI6 instances can be used on
customer design without the clock driver error:
stm32mp1_clk_get_id: clk id 131 not found
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
lpd_lsbus is clock which is used by many IPs like dmas, gems, gpio, sdhcis,
spis, ttcs, uarts, watchdog that's why make sense to also enable access to
change this clock. For this clock you already get the rate.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add the support of SYSCFG clock used by syscon driver
to prepare the clock management of STM32MP_SYSCON_SYSCFG.
This clock is already defined in kernel device tree,
stm32mp151.dtsi but not yet supported in the syscon driver:
syscfg: syscon@50020000 {
compatible = "st,stm32mp157-syscfg", "syscon";
reg = <0x50020000 0x400>;
clocks = <&rcc SYSCFG>;
};
It is safe to support this clock in U-Boot driver with
RCC_MC_APB3ENSETR, Bit 11 SYSCFGEN: SYSCFG peripheral clocks
enable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When the default clocks cannot be set, the clock is silently probed and
the error is ignored. This is incorrect, since having the clocks at the
correct speed may be important for operation of the system.
Fix it by checking the return code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Setting DM_FLAG_PRE_RELOC for Armada 3720 clock drivers (TBG and
peripheral clocks) makes it possible for serial driver to retrieve clock
rates via clk API.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace 'pciaux' with 'pcieaux', including name string and function
prefix. The old name string, 'pciaux', might cause an error if PCIe
driver is changed to use clk_get_by_name() with 'pcieaux' to get
clock.
Signed-off-by: Green Wan <green.wan@sifive.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYN105QAKCRDKSWXLKUoM
IZiFAJ9CIiEpHiBbnAhA0VOMGoaXHGULywCdED/5dNgVtc1C7y4avzETbEyWzD4=
=CdMa
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.10
clk:
- Add driver for Xilinx Clocking Wizard IP
fdt:
- Also record architecture in /fit-images
net:
- Fix plat/priv data handling in axi emac
- Add support for 10G/25G speeds
pca953x:
- Add missing dependency on i2c
serial:
- Fix dependencies for DEBUG uart for pl010/pl011
- Add setconfig option for cadence serial driver
watchdog:
- Add cadence wdt expire now function
zynq:
- Update DT bindings to reflect the latest state and descriptions
zynqmp:
- Update DT bindings to reflect the latest state and descriptions
- SPL: Add support for ECC DRAM initialization
- Fix R5 core 1 handling logic
- Enable firmware driver for mini configurations
- Enable secure boot, regulators, wdt
- Add support xck devices and 67dr
- Add psu init for sm/smk-k26 SOMs
- Add handling for MMC seq number via mmc_get_env_dev()
- Handle reserved memory locations
- Add support for u-boot.itb generation for secure OS
- Handle BL32 handoffs for secure OS
- Add support for 64bit addresses for u-boot.its generation
- Change eeprom handling via nvmem aliases
Add clock tables for R8A779A0 V3U SoC from Linux 5.12,
commit 9f4ad9e425a1 ("Linux 5.12")
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
--
Marek: - Add .reset_modemr_offset
- Sync tables from Linux 5.12
- Rebase on latest u-boot
On R8A779A0 V3U SoC, PLL1 and PLL5 use a divider value
from cpg_pll_configs table while PLL{20,21,30,31,4} use
different control offset. Introduce new types to handle
this and handle those types in the Gen3 clock code.
Based on "clk: renesas: Add support for R8A779A0 V3U PLLn"
by Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The Clocking Wizard IP supports clock circuits customized
to your clocking requirements. The wizard support for
dynamically reconfiguring the clocking primitives for
Multiply, Divide, Phase Shift/Offset, or Duty Cycle.
Limited by U-Boot clk uclass without set_phase API, this
patch only provides set_rate to modify the frequency.
Signed-off-by: Zhengxun <zhengxunli.mxic@gmail.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove the tab in clk_get_bulk to respect the coding rules.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Now that we have only one clock driver, we don't need to have our own
subdirectory. Move the driver back with the rest of the clock drivers.
The MAINTAINERS for kendryte pinctrl is also fixed since it has always been
wrong.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This driver no longer serves a purpose now that we have moved away from
CCF. Drop it.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This speeds up boot by preventing multiple reconfigurations of the PLLs.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
This adds support for setting clock rates, which was left out of the
initial CCF expunging. There are several tricky bits here, mostly related
to the PLLS:
* The PLL's bypass is broken. If the PLL is reconfigured, any child clocks
will be stopped.
* PLL0 is the parent of ACLK which is the CPU and SRAM's clock. To prevent
stopping the CPU while we configure PLL0's rate, ACLK is reparented
to IN0 while PLL0 is disabled.
* PLL1 is the parent of the AISRAM clock. This clock cannot be reparented,
so we instead just disallow changing PLL1's rate after relocation (when
we are using the AISRAM).
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
