Commit graph

151 commits

Author SHA1 Message Date
Yangbo Lu
4d8ff42e46 mmc: fsl_esdhc: drop i.MX code
Dropped i.MX code which couldn't be reused.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
2019-06-23 14:18:42 +08:00
Yangbo Lu
66fa035b55 mmc: fsl_esdhc: fix probe issue without CONFIG_BLK enabled
u-boot is trying to make CONFIG_BLK as a hard requirement
for DM_MMC. But now it's still not.

config BLK
	bool "Support block devices"
	depends on DM
	default y if DM_MMC

When fsl_esdhc driver was reworked for DM_MMC support, DM_MMC
without CONFIG_BLK enabled wasn't considered. This patch is to
fix probe issue without CONFIG_BLK enabled.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19 12:54:56 +05:30
Yinbo Zhu
b69e1d0bc7 driver: mmc: adopt 32 bit addr in fsl_esdhc for CONFIG_PPC
PowerPC supports 32 bit address.
So adopt 32 bit addr in fsl_esdhc for CONFIG_PPC.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-05-23 14:22:33 +05:30
Yinbo Zhu
b512d07e8c driver: mmc: set sdhc clock in fsl_esdhc for CONFIG_PPC
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-05-23 14:22:33 +05:30
Lukasz Majewski
b6a0427554 Revert "mmc: fsl_esdhc: fix sd/mmc ddr mode clock setting issue"
This reverts commit 72a89e0da5, which
causes the imx53 HSC to hang as the eMMC is not working properly anymore.

The exact error message:
MMC write: dev # 0, block # 2, count 927 ... mmc write failed
0 blocks written: ERROR

imx53 is not using the DDR mode.

Debugging of pre_div and div generation showed that those values are
generated in a way, which is not matching the ones from working setup.

As the original patch was performing code refactoring, let's revert this
change, so all imx53 boards would work again.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-05-20 11:34:27 +08:00
Ye Li
da8e1f3cd4 mmc: fsl_esdhc: Fix wp_enable issue
The wp-gpios property is used for gpio, if this is set, the WP pin is muxed
to gpio function, can't be used as internal WP checking. However the codes
remain to use internal WP checking.

This patch changes to examine the "fsl,wp-controller" for enabling internal WP
checking, and "wp-gpios" for muxing to gpio.

Signed-off-by: Ye Li <ye.li@nxp.com>
2019-05-03 20:04:30 +08:00
Ye Li
72a89e0da5 mmc: fsl_esdhc: fix sd/mmc ddr mode clock setting issue
When sd/mmc work at DDR mode, like HS400/HS400ES/DDR52/DDR50 mode,
the output clock rate is half of the internal clock rate.

This patch set the DDR_EN bit first for DDR mode, hardware divide
the usdhc clock automatically, then follow the original sdr clock
setting method.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
2019-05-03 20:03:41 +08:00
Abel Vesa
d76706c89a mmc: fsl_esdhc: Fix DM_REGULATOR ifdefs for SPL builds
Since the fsl_esdhc will also be used by SPL, make the
preprocessor switches more generic to allow any kind of build.

Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-02-15 22:01:15 +01:00
Tom Rini
748ad078ee For 2019.04
-----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAlxQnKQPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3Mm8L/0P99AB62Pu0NbAaVI9PnqaeR9/kUIvHlaPT
 RMuUIz931/1GDnugGsEEquSMUt69lfBCKYbF4sKiWObytHfYKvB/u638gqG2IoEt
 KcnWU5dagaTOyoyPOtr8EyKxThJtG2j1uN+fA5BCZ6A6CLnEW0biJXYLwN5P/DIE
 bsn9R+XfOV/ppaFh3p65SZfzzwKh6eUQLHqEphBbbAHCPz74QSeZMHkumbKplGOk
 1cjuFi8bekFnPGDDPW8jRvUNlhRD0kTjXoBj1eF2Q1g8lUj6La8yOsq1DAeGJjd1
 ywUDi8GPNYQ7HuHNzfZETWAYspNflARnPQwMemmNSKmmu6CO8aB6lt3JZWEUrnjL
 1D8LzMrRpyq1jEA0a57qsvTc8i3KA7X3FHTszP0flhiLKgBgE+5t1w8dc0wxC7HZ
 eF9TE3tGAmVzRVZwBh8HIDuKhe+y3uGKtvxl80DF8vQQWrXHq0GSC+pmdEXk7DGU
 OGYvdvVoThglZwM4vqeKlT/+1KLPCQ==
 =dOOt
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20190129' of git://git.denx.de/u-boot-imx

For 2019.04
2019-01-30 07:22:12 -05:00
Patrick Bruenn
791c88da31 mmc: fsl_esdhc: add compatible for fsl, imx53-esdhc
Add compatible "fsl,imx53-esdhc" to keep mmc working on i.MX53 platforms
with CONFIG_DM_MMC=y

Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2019-01-28 20:55:46 +01:00
Angelo Dureghello
1f15cb8f5b drivers: esdhc: add support for ColdFire mcf5441x family
This patch has been tested on the mcf54415-based stmark2
board. The eSDHC driver works reliably using DMA mode.

Signed-off-by: Angelo Dureghello <angelo@sysam.it>
2019-01-26 08:13:56 -05:00
Yinbo Zhu
7a0425dd96 mmc: fsl_esdhc: make get_cd work well in dm_mmc_ops
This patch is to make get_cd work well when DM_MMC enabled

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2019-01-17 13:17:10 -08:00
Fabio Estevam
29c2edb42b mmc: fsl_esdhc: Avoid infinite loop in esdhc_send_cmd_common()
The following hang is observed on a Hummingboard 2 MicroSOM
i2eX iMX6D - rev 1.3 with no eMMC populated on board:

U-Boot SPL 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)
Trying to boot from MMC1

U-Boot 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)

CPU:   Freescale i.MX6D rev1.5 996 MHz (running at 792 MHz)
CPU:   Extended Commercial temperature grade (-20C to 105C) at 33C
Reset cause: POR
Board: MX6 HummingBoard2
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

No panel detected: default to HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
---> hangs

which is caused by the following infinite loop inside esdhc_send_cmd_common()

	while (!(esdhc_read32(&regs->irqstat) & flags))
		;

Instead of looping forever, provide an exit path so that a timeout
error can be propagated in the case irqstat does not report
any interrupts, which may happen when no eMMC is populated on
board.

Reported-by: Ricardo Salveti <rsalveti@rsalveti.net>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Ricardo Salveti <rsalveti@rsalveti.net>
2019-01-14 11:26:12 -05:00
Peng Fan
cd357ad112 imx: rename mx8m,MX8M to imx8m,IMX8M
Rename mx8m,MX8M to imx8m,IMX8M

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jon Nettleton <jon@solid-run.com>
2019-01-01 14:12:18 +01:00
Peng Fan
3cb1450380 mmc: fsl_esdhc: add uclass clk support
When CONIFG_CLK is enabled, use uclass clk api to handle
the clock.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
2018-10-22 13:00:09 +02:00
Ye Li
d423c93b66 fsl_esdhc: Update usdhc driver to support i.MX8
Add CONFIG_ARCH_IMX8 to use the 64bits support in usdhc driver.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
2018-10-22 13:00:09 +02:00
Peng Fan
c76382ff7f mmc: fsl_esdhc: enable HS400 feature
The strobe dll code is ported from Linux Kernel:
drivers/mmc/host/sdhci-esdhc-imx.c
The comments are from the above file,
"For HS400 eMMC, there is a data_strobe line. This signal is generated
by the device and used for data output and CRC status response output
in HS400 mode. The frequency of this signal follows the frequency of
CLK generated by host. The host receives the data which is aligned to the
edge of data_strobe line. Due to the time delay between CLK line and
data_strobe line, if the delay time is larger than one clock cycle,
then CLK and data_strobe line will be misaligned, read error shows up.
So when the CLK is higher than 100MHz, each clock cycle is short enough,
host should configure the delay target. "

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
2018-09-10 20:48:19 -04:00
Jaehoon Chung
6511718254 mmc: add the MMC_CLK_ENABLE/DISABLE macro in mmc.h
mmc_set_clock() function has the disable argument as bool type.
When mmc_set_clock is called, it might be passed to "true" or "false".
But it's too confusion whether clock is enabled or disabled with only
"true" and "false".
To prevent the confusion, replace to MMC_CLK_ENABLE/DISABLE macro from
true/false.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-05-08 13:12:33 +09:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Peng Fan
51313b49f2 mmc: fsl_esdhc: support SDR104 and HS200
Introduce SDR104 and HS200 support
The implementation takes linux kernel sdhci.c and sdhci-esdhc-imx.c
as reference.
 - Implement esdhc_change_pinstate to dynamically change pad settings
 - Implement esdhc_set_timing
 - Implement esdhc_set_voltage to switch voltage
 - Implement fsl_esdhc_execute_tuning to execute time process
 - Enlarge the cfg->f_max to 200MHz.
 - Parse fsl,tuning-step, fsl,tuning-start-tap and
   fsl,strobe-dll-delay-target from device tree.
 - Parse no-1-8-v property
 - Introduce esdhc_soc_data to indicate the flags and caps

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-02-04 12:00:58 +01:00
Peng Fan
59d3782cda mmc: fsl_esdhc: add strobe and tuning entry
Add entries that will be used for tuning control.
The whole layout not changed, just expand reserved3[84] and
rename other reservedx in sequence.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-02-04 12:00:58 +01:00
Peng Fan
eec2d43795 mmc: fsl_esdhc: support i.MX8M
Support i.MX8M in fsl esdhc driver.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-02-04 12:00:58 +01:00
Benoît Thébaudeau
b9b4f146c9 mmc: fsl_esdhc: Fix i.MX53 eSDHCv3 clock
Commit 4f425280fa ("mmc: fsl_esdhc: Allow all supported prescaler
values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR mode on
i.MX, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.

Fix this issue by changing the minimum prescaler value for the single
instance of the i.MX53 eSDHCv3 controller.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-01-22 14:17:13 +09:00
Peng Fan
db359efd59 mmc: fsl_esdhc: Fix eMMC 1.8v setting issue
Current USDHC driver will reset VSELECT to 0 (3.3v) during mmc init,
then set to 1 for 1.8v eMMC I/O. When booting from eMMC, since ROM has
already set VSELECT to 1.8v before running the u-boot. This reset in
USDHC driver causes a short 2.2v pulse on CMD pin.

Fix this issue by not reset VSELECT to 0 when 1.8v flag is set.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2018-01-13 00:08:44 +09:00
Kishon Vijay Abraham I
35f6782055 mmc: add a new mmc parameter to disable mmc clock
mmc clock has to be disabled in certain cases like during
the voltage switch sequence. Modify mmc_set_clock function
to take disable as an argument that signifies if the
clock has to be enabled or disabled.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2018-01-12 18:11:04 +09:00
Benoît Thébaudeau
bcfb365375 mmc: fsl_esdhc: Fix PIO timeout
The following error has been observed on i.MX25 with a high-speed SDSC
card:
    Data Write Failed in PIO Mode.

It was caused by the timeout set on PRSSTAT.BWEN, which was triggered
because this bit takes 15 ms to be set after writing the first block to
DATPORT with this card. Without this timeout, all the blocks are
properly written.

This timeout was implemented by decrementing a variable, so it was
depending on the CPU frequency. Fix this issue by setting this timeout
to a long enough absolute duration (500 ms).

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-11-07 10:26:27 +01:00
Simon Glass
e7881d85a9 dm: mmc: Drop CONFIG_DM_MMC_OPS
All boards which use DM_MMC have now been converted to use DM_MMC_OPS.
Drop the option and good riddance.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:59:55 +09:00
Simon Glass
5248930ebf dm: imx: cm_fx6: Enable more driver model support
Enable driver model for MMC (including BLK), SATA and USB. Note that USB
does not yet work correctly since the nodes are disabled. Hopefully this
can be resolved by the maintainer.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
653282b567 dm: mmc: fsl_esdhc: Update to support MMC operations
This driver does not currently support CONFIG_DM_MMC_OPS. Update it to
fully convert it to driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
4aac33f510 dm: mmc: fsl_esdhc: Update to support livetree
Update this driver to support a live device tree.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
d6eb25e987 dm: mmc: fsl_esdhc: Drop mmc_init() call from fsl_esdhc_init()
We want to use fsl_esdhc_init() with driver model. Move the mmc_init() out
of this function so that we can use it for our common init.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
e88e1d9c04 dm: mmc: fsl_esdhc: Set up platform data
With driver model we want to store the mmc and configuration structure in
platform data. Set up structure up and use it for non-DM as well.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
201e828b22 dm: mmc: fsl_esdhc: Detect init failure
Since esdhc_init_common() can fail it should return an error code. Update
this and also adjust the timeout mechanism to use get_timer(), which is a
more common approach.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
446e077a21 dm: mmc: fsl_esdhc: Detect reset failure
Since esdhc_reset() can fail it should return an error code. Update this
and also adjust the timeout mechanism to use get_timer(), which is a more
common approach.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
9586aa6ea3 dm: mmc: fsl_esdhc: Set up common versions of operations
Driver model wants to use the core functions in this file but accesses the
driver-private data in a different way. Move the code into new 'common'
functions and set up stubs to call these. Also sort the operations into
alphabetical order for consistency.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Simon Glass
09b465fd0f dm: mmc: fsl_esdhc: Pass private data to internal functions
With driver model we will not use mmc->priv to access driver-private data.
To accomodate this, update internal functions so that we can pass the
private data directly. This will allow the caller to obtain it as it
prefers.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-17 16:44:17 +09:00
Yang Li
590e87d1a6 mmc: fsl_esdhc: not always setting esdhc fdt status to okay
We shouldn't always change the status to okay.  There could be
situations that the esdhc is intentionally disabled in the device
tree.

Signed-off-by: Li Yang <leoyang.li@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-08-09 09:57:32 -07:00
York Sun
9bb272e90a driver: mmc: fsl_esdhc: Fix compiling warning
Commit 4483b7eb added variable vqmmc_dev but only uses it under
CONFIG_DM_REGULATOR. Add the same macro to variable declaration to
get rid of compiling warning.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-08-09 09:11:29 -07:00
Peng Fan
f34ccce50a mmc: fsl_esdhc: drop CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT
CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT is not the correct method
to set I/O to 1.8. To boards that does not support vqmmc-supply,
use vs18_enable in fsl_esdhc_cfg. If regulator is supported,
use fixed 1.8V regulator for vqmmc-supply.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-07-12 09:44:22 +02:00
Peng Fan
4483b7eb88 dm: mmc: fsl_esdhc: handle vqmmc supply
Handle vqmmc supply. Some boards have a fixed I/O voltage
at 1.8V for emmc, so the usdhc also needs to be configured
as 1.8V by setting VSELECT bit. The vs18_enable is the one
that used to checking whether setting VSELECT or not in
the driver. So if vqmmc supply is 1.8V, set vs18_enable,
the driver will set VSELECT.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2017-07-12 09:44:22 +02:00
Peng Fan
32a9179f3a mmc: fsl_esdhc: introduce vs18_enable for 1.8V fix I/O
When using eMMC with 1.8V I/O, the VSELECT bit need to be set in
the USDHC controller when init.

This patch adds a parameter "vs18_enable" in fsl_esdhc_cfg
structure and priv data, so each controller can have different
settings.

We could not use CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT, it has problem
that it will apply to all USDHC controllers and it only set the 1.8V
at init phase. So if user does not select to the eMMC device,
the voltage on the I/O pins are not correct.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-07-12 09:44:22 +02:00
Tom Rini
821560fd8e Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/imx6qdl_icore_rqs.h
	include/configs/imx6ul_geam.h
	include/configs/imx6ul_isiot.h
2017-06-27 09:32:37 -04:00
Simon Glass
150c5afe5b dm: gpio: Add live tree support
Add support for requesting GPIOs with a live device tree.

This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.

Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-01 07:03:10 -06:00
Simon Glass
a821c4af79 dm: Rename dev_addr..() functions
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.

In the end we will have:

   1. dev_read_addr...()    - works on devices, supports flat/live tree
   2. devfdt_get_addr...()  - current functions, flat tree only
   3. of_get_address() etc. - new functions, live tree only

All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.

Note this involves changing some dead code - the imx_lpi2c.c file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-06-01 07:03:01 -06:00
Jagan Teki
2e87c440f6 mmc: fsl_esdhc: Move non DM_MMC code in #ifndef CONFIG_DM_MMC
Don't build non DM_MMC code when DM_MMC defined so move
them into #ifndef CONFIG_DM_MMC

Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-31 10:21:24 +02:00
Benoît Thébaudeau
4f425280fa mmc: fsl_esdhc: Allow all supported prescaler values
On i.MX, SYSCTL.SDCLKFS may be set to 0 in order to make the SD clock
frequency prescaler divide by 1 in SDR mode. In DDR mode, the prescaler
can divide by up to 512. Allow both of these settings.

The maximum SD clock frequency in High Speed mode is 50 MHz. On i.MX25,
this change makes it possible to get 48 MHz from the USB PLL
(240 MHz / 5 / 1) instead of only 40 MHz from the USB PLL
(240 MHz / 3 / 2) or 33.25 MHz from the AHB clock (133 MHz / 2 / 2).

Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-05-31 10:14:00 +02:00
Peng Fan
b60f14574e mmc: fsl_esdhc: support i.MX7ULP
Add compatible property for i.MX7ULP.
Add a weak init_usdhc_clk function, i.MX7ULP use this to init the clock.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Simon Glass
e160f7d430 dm: core: Replace of_offset with accessor
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-02-08 06:12:14 -07:00
Tom Rini
0675f992db Merge git://git.denx.de/u-boot-fsl-qoriq 2017-01-19 12:22:23 -05:00
Yangbo Lu
fce1e16c55 mmc: fsl_esdhc: move 'status' property fixup into a weak function
Move fdt fixup of 'status' property into a weak function. This allows
board to define 'status' fdt fixup by themselves.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:46:30 -08:00