Fixes a compilation failure with disabled PXE or DHCP command when using
sunxi platform.
Signed-off-by: Ondřej Jirman <megous@megous.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- 16GB eMMC
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- USB 2.0 and 3.0 Host
- HDMI port
- S/PDIF port
- 5V/2A DC power supply
- Wi-Fi/BT via Fn-Link 6222B-SRB (RTL8222BS)
Linux commit details about the sun50i-h6-beelink-gs1.dts sync:
"arm64: dts: allwinner: h6: Introduce Beelink GS1 board"
(sha1: 089bee8dd119ba084dee6b17a2e1a53df4f30193)
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add the DM_MMC-compatible DesignWare MMC driver support for Synopsys
ARC devboards. It is created to switch ARC devboards to use DM_MMC.
It required information such as clocks (Bus Interface Unit clock,
Card Interface Unit clock) and SDIO bus width.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly262oACgkQykllyylKDCH44gCbBnuxUH6ZF0B7Leuee4te7C59
LmUAn14/bbtMt17zkMSADCjY9yGWF4au
=mWrW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblaze
Xilinx/FPGA changes for v2019.07
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
Convert driver to use spi-mem ops in order to support accelerated MMIO
flash interface in generic way and for better performance.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Now that all boards using TI QSPI have moved to DM and DT, drop non DM
code completely.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[jagan: update MIGRATION.txt, rebase config_whitelist.txt]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
It seems like the Allwinner SATA driver is already quite capable of
using the driver model, so we can force this on all boards and can
remove support for a non-DM_SCSI build.
This removes the warning about boards with SATA ports not being
DM_SCSI compliant.
It also takes the opportunity to move the driver out of the board/sunxi
directory to join its siblings in drivers/ata, and to make it a proper
Kconfig citizen.
The board defconfigs stay untouched.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: select DM_SCSI separately]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Enable DM_MMC if MMC defined
- Enable DM_SCSI if SCSI defined
globally through Allwinner platform, the effected SoC families
and boards will make use of MMC and SCSI subsystems in driver-model.
Tested DM_MMC in one board from A64, H6, H5, H3, R40, A83T, A20, A10
SoCs.
Tested-by: Pablo Sebastián Greco <pgreco@centosproject.org> # BPI-M2-Ultra
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for BPI-M2-Berry, this would require since
we have DM_SCSI enabled on the respective SoC.
Unable to sync the same node from Linux, since the similar change
is still in Linux ML.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for a20-wits-pro-a20-dkt, this would require since
we have DM_SCSI enabled on the respective SoC.
Right now, ahci enabled in -u-boot.dtsi and will remove once same
supported by Linux.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable ahci node for sun7i-a20-m5.dts, this would require since
we have DM_SCSI enabled on the respective SoC.
No need to send patch to Linux for this change, since this
dts is U-Boot specific.
Cc: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync sun7i-a20 dts(i) files from Linux 5.1-rc2
Linux commit details about the sun7i-a20* sync:
"ARM: dts: sun7i: bananapi: Add GPIO banks regulators"
(sha1: 09c6572290f018d73ec2e812e28bada34d41815f)
Here are U-Boot specific dts changes.
- s/uart0_pins_a/uart0_pb_pins for
sun7i-a20-ainol-aw1.dts
sun7i-a20-m5.dts
sun7i-a20-primo73.dts
sun7i-a20-yones-toptech-bd1078.dts
sunxi-itead-core-common.dtsi
- s/gmac_pins_mii_a/gmac_rgmii_pins for
sun7i-a20-m5.dts
- drop i2c0, i2c1 pins from
sunxi-itead-core-common.dtsi
- drop mmc0 pins from
sun7i-a20-primo73.dts
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync sun8i-r40 dts(i) files from Linux 5.1-rc2
Linux commit details about the sun8i-r40* sync:
"ARM: dts: sun8i: r40: bananapi-m2-ultra: Add Bluetooth device node"
(sha1: 1e5f1db4ccd8348a21da55bff82f4263000879ef)
Linux commit details about the sun8i-v40* sync:
"ARM: dts: sunxi: Fix I2C bus warnings"
(sha1: 0729b4af5753b65aa031f58c435da53dbbf56d19)
Cc: Pablo Sebastián Greco <pgreco@centosproject.org>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Since Ethernet clock and reset is now handling via
CLK and RESET frameworks via driver API's remove
explicit ccm writes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CLK and RESET support for sun8i_emac driver to
enable TX clock and reset pins via CLK and RESET
framework.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Unlike other Allwinner SoC's R40 GMAC clock control register
is locate in CCU, but rest located via syscon itself. Since
the phandle property for current code look for 'syscon' and
it will grab the respective ccu or syscon base address based
on DT property defined in respective SoC dtsi.
So, use the existing 'syscon' code even for R40 for retrieving
GMAC clock via CCU and update the register directly in
sun8i_emac_set_syscon instead of writing it separately using
ccm base.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CLk support for sunxi_emac to enable AHB_EMAC clock
via CLK framework.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
GMAC reset reg offset added by below commit seems to assume
it as EMAC but R40 indeed using GMAC.
"clk: sunxi: Implement EMAC, GMAC clocks, resets"
(sha1: 68620c9698)
So, fix by updating the reg offset for RST_BUS_GMAC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
A missing CONFIG_ prefix while checking for this Kconfig variable makes the
check always fail. Fix it. While there also switch from the '#if defined'
form to the '#ifdef' form as the other checks in this function.
Fixes: 35e2b92344 ("arm64: zynqmp: Fix logic around CONFIG_ZYNQ_SDHCI")
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
By moving to DM_I2C there is no need to specify any eeprom configuration
because it is read from DT.
Reported-by: Sreeja Vadakattu <sreeja.vadakattu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The phydev supported features were reset in phy_set_supported() so,
move the setting of driver supported features after this so that it
wont lost in phy_set_supported().
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Prioritize external dtb if its passed via EXT_DTB
than the dtb that was built in the tree. With this
patch it appends the specified external dtb to
the u-boot image.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Post configuration cant be run at u-boot as u-boot
didn't has any info about the design.So,this patch
adds an info message that post config was not run
and needs to be run manually if needed.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds "zu39dr" to the list of zynqmp devices
The zu39DR is the new RFSoC silicon with id value of 0x66.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Update EXTRA_ENV_SETTINGS and related commands to use 'setenv'
instead of short name 'set' in commands.
E.g. in case command setexpr is enabled the short form does not work
properly as the name becomes ambigous.
Fixes error messages like:
U-Boot> set
Unknown command 'set' - try 'help'
Signed-off-by: Tomas Melin <tomas.melin@vaisala.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The commit 'f48ef0d81aa837a33020f8d61abb3929ba613774' did break I2C
support because requesting the clock for the I2C ip-block isn't
supported during SPL.
To fixup this we add support requesting clocks for:
- i2c0
- i2c1
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove unneeded configs from mini qspi configuration
so that it saves space for this mini configuration.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define a label for flash node so that it can be
referenced easily as required.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
spi-flash compatible string is needed for reading tx and rx bus
widths, hence add this compatible string to flash node.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch checks for zynq aes & rsa commands max parameters count. Also
checks minimum number of parameters count for aes command.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Changed the return type of reset_reason() to int from u32, because
zynqmp_mmio_read/write() returns signed value on error.
Replaced readl and writel functions with zynqmp_mmio_read &
zynqmp_mmio_write functions to access RESET_REASON(CRL_APB) registers.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch fixes the tap delay values to be set at 100MHz and 150MHz
as per TRM by fixing the if condition to use <= instead of <.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not enable WDT by default on this target because distributions are
not enabling watchdog driver to service it.
Feature has been enabled by:
"arm64: zynqmp: Enable cadence WDT for zcu100"
(sha1: 767afebbcd)
And WDT is still enabled in rebranded Avnet Ultra 96 board support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Images are created
mkimage -f fit.its -E download-fit-external.ub
and test expects these entries.
env__fpga_under_test = {
...
"mkimage_fit_external": download-fit-external.ub",
"mkimage_fit_external_size": xxxxx,
...
}
Test download file and loads it to fpga.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Ensure the string for filename is always constant, otherwise it can be
corrupted by the writing.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This function supports getting both data address and length for
existing FPGA subimage and FPGA external data.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
-----BEGIN PGP SIGNATURE-----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=KLsH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imx
Move to DM
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
In the aarch64 crash dump information about the loaded EFI images is added.
In README.uefi the development target is for the UEFI subsystem is
described as "Embedded Base Boot Requirements (EBBR) Specification"
compliance.
Several bug fixes are supplied.
-----BEGIN PGP SIGNATURE-----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=QdJl
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc1-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc1 (2)
In the aarch64 crash dump information about the loaded EFI images is added.
In README.uefi the development target is for the UEFI subsystem is
described as "Embedded Base Boot Requirements (EBBR) Specification"
compliance.
Several bug fixes are supplied.
