Commit graph

110 commits

Author SHA1 Message Date
Tom Rini
0e14cdfaf3 Convert CONFIG_ETHPRIME to Kconfig
This converts the following to Kconfig:
   CONFIG_ETHPRIME

This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME
similar to other options that are not always set and control environment
variables.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18 12:48:17 -04:00
Tom Rini
f9147d636c Convert CONFIG_CHIP_SELECTS_PER_CTRL to Kconfig
This converts the following to Kconfig:
   CONFIG_CHIP_SELECTS_PER_CTRL

Cc: Alison Wang <alison.wang@nxp.com>
Cc: Pramod Kumar <pramod.kumar_1@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-03 16:51:20 -05:00
Tom Rini
fdfb17b1f5 Convert CONFIG_BOOTFILE to Kconfig
This converts the following to Kconfig:
   CONFIG_BOOTFILE

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-03 16:51:20 -05:00
Tom Rini
54c5c2b8fe configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-01-24 17:36:30 -05:00
Tom Rini
f76750d111 Convert CONFIG_CONS_INDEX et al to Kconfig
This converts the following to Kconfig:
   CONFIG_CONS_INDEX
   CONFIG_DEBUG_UART_CLOCK
   CONFIG_FSL_TZPC_BP147
   CONFIG_GENERIC_ATMEL_MCI
   CONFIG_IDENT_STRING
   CONFIG_LIBATA
   CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE
   CONFIG_LPC32XX_GPIO
   CONFIG_MP
   CONFIG_MPC8XXX_GPIO
   CONFIG_MTD_PARTITIONS
   CONFIG_MVGBE
   CONFIG_MXC_GPIO
   CONFIG_NR_DRAM_BANKS
   CONFIG_OF_BOARD_SETUP
   CONFIG_OF_STDOUT_VIA_ALIAS
   CONFIG_OF_SYSTEM_SETUP
   CONFIG_PREBOOT
   CONFIG_ROCKCHIP_SERIAL
   CONFIG_RTC_ENABLE_32KHZ_OUTPUT
   CONFIG_RTC_MV
   CONFIG_SCSI_AHCI
   CONFIG_SF_DEFAULT_BUS
   CONFIG_SF_DEFAULT_CS
   CONFIG_SF_DEFAULT_SPEED
   CONFIG_SOFT_SPI
   CONFIG_SPI_FLASH_EON
   CONFIG_SPI_FLASH_MACRONIX
   CONFIG_SPI_FLASH_MTD
   CONFIG_SPI_FLASH_SPANSION
   CONFIG_SPI_FLASH_SST
   CONFIG_SPI_FLASH_STMICRO
   CONFIG_SUPPORT_RAW_INITRD
   CONFIG_SYS_ARCH_TIMER
   CONFIG_SYS_BOARD
   CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
   CONFIG_SYS_DCACHE_OFF
   CONFIG_SYS_FDT_SAVE_ADDRESS
   CONFIG_SYS_FLASH_CFI
   CONFIG_SYS_FSL_ERRATUM_ESDHC135
   CONFIG_SYS_HAS_SERDES
   CONFIG_SYS_L2CACHE_OFF
   CONFIG_SYS_LITTLE_ENDIAN
   CONFIG_SYS_LOAD_ADDR
   CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
   CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
   CONFIG_SYS_NS16550
   CONFIG_SYS_PLLFIN
   CONFIG_SYS_SPI_U_BOOT_OFFS
   CONFIG_TIMER_SYS_TICK_CH
   CONFIG_USB_EHCI_FSL
   CONFIG_U_QE
   CONFIG_VERSION_VARIABLE

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27 08:41:38 -05:00
Tom Rini
c7fad78ec0 Convert CONFIG_SYS_BR0_PRELIM et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_BR0_PRELIM
   CONFIG_SYS_OR1_PRELIM
   CONFIG_SYS_BR1_PRELIM
   CONFIG_SYS_OR2_PRELIM
   CONFIG_SYS_BR2_PRELIM
   CONFIG_SYS_OR2_PRELIM
   CONFIG_SYS_BR3_PRELIM
   CONFIG_SYS_OR3_PRELIM
   CONFIG_SYS_BR4_PRELIM
   CONFIG_SYS_OR4_PRELIM
   CONFIG_SYS_BR5_PRELIM
   CONFIG_SYS_OR5_PRELIM
   CONFIG_SYS_BR6_PRELIM
   CONFIG_SYS_OR6_PRELIM
   CONFIG_SYS_BR7_PRELIM
   CONFIG_SYS_OR7_PRELIM

This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so.  Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-01 10:58:10 -05:00
Tom Rini
970bf8603b Convert CONFIG_USE_BOOTCOMMAND et al to Kconfig
This converts the following to Kconfig:
   CONFIG_USE_BOOTCOMMAND
   CONFIG_BOOTCOMMAND
   CONFIG_RAMBOOTCOMMAND
   CONFIG_NFSBOOTCOMMAND

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-01 10:58:10 -05:00
Tom Rini
9802154a94 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-01 12:19:22 +00:00
Tom Rini
cdcbd593ad configs: Resync with savedefconfig
Resync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-10-15 09:42:22 -04:00
Simon Glass
6f004adaf6 ppc: Rename MPC8XXX_INIT_DDR_SUPPORT to MPC8XXX_INIT_DDR
Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-04 12:26:02 -04:00
Simon Glass
ea2ca7e17e spi: Rename SPI_SUPPORT to SPI
Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-04 12:26:02 -04:00
Simon Glass
2a73606668 serial: Rename SERIAL_SUPPORT to SERIAL
Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-09-04 12:26:01 -04:00
Tom Rini
7cfbba36e9 Convert CONFIG_SYS_MALLOC_LEN to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_MALLOC_LEN

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
2021-08-31 17:47:49 -04:00
Tom Rini
efb5dab7ba nxp: Migrate CONFIG_DDR_CLK_FREQ to Kconfig
As this symbol can either be a fixed value or the function
get_board_ddr_clk, migration is tricky.  Introduce a choice of DYNAMIC
or STATIC_DDR_CLK_FREQ.  If DYNAMIC, we continue to use the board
defined get_board_ddr_clk function.  If STATIC, set CONFIG_DDR_CLK_FREQ
to that value and now include/clock_legacy.h contains the function
prototype or defines get_board_ddr_clk() to that static value.  Update
callers to test for DYNAMIC or STATIC.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31 17:46:37 -04:00
Tom Rini
fc8d3b9a2f Convert CONFIG_I2C_SET_DEFAULT_BUS_NUM et al to Kconfig
This converts the following to Kconfig:
   CONFIG_I2C_SET_DEFAULT_BUS_NUM
   CONFIG_I2C_DEFAULT_BUS_NUMBER

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30 14:10:08 -04:00
Tom Rini
6d5d0c955e i2c: fsl_i2c: Migrate to Kconfig
- As there are no boards that use different values for speed / slave on
  different buses, use a single option.
- Switch to using the common SYS_I2C_SPEED / SYS_I2C_SLAVE options.
- Introduce _HAS_ options for additional buses as only the first one is
  common to all users.
- Convert all remaining symbols to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30 14:10:07 -04:00
Tom Rini
55dabcc8f2 Convert CONFIG_SYS_I2C_LEGACY to Kconfig and add CONFIG_[ST]PL_SYS_I2C_LEGACY
First, we convert CONFIG_SYS_I2C_LEGACY to Kconfig.  Next, as you cannot
have SYS_I2C_LEGACY and DM_I2C at the same time, introduce
CONFIG_SPL_SYS_I2C_LEGACY so that we can enable the legacy option only
in SPL.  Finally, for some PowerPC cases we also need
CONFIG_TPL_SYS_I2C_LEGACY support.  Convert all of the existing users to
one or more symbols.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30 14:10:07 -04:00
Tom Rini
88cd7d0ea9 Convert CONFIG_SYS_I2C_EEPROM_ADDR et al to Kconfig
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR
  based on current usage.
- Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN,
  CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE
  CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS
  to Kconfig.  We move these symbols around a bit and add appropriate
  dependencies to them.  In some cases, we now add a correct default value
  as well.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-30 14:10:06 -04:00
Simon Glass
975e7cf301 i2c: Rename SPL/TPL_I2C_SUPPORT to I2C
Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-28 14:29:37 -04:00
Tom Rini
df59b7d23b configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-26 21:10:37 -04:00
Tom Rini
9926df89b2 configs: Remove unnecessary CONFIG_DM_PCI_COMPAT=y
The following boards no longer need CONFIG_DM_PCI_COMPAT enabled, so
remove that.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-07-07 19:52:25 -04:00
Tom Rini
2bba78076b configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-06-28 10:17:29 -04:00
Tom Rini
838157d02e configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-05-11 12:19:09 -04:00
Tom Rini
0817daa760 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-09 12:22:06 -04:00
Tom Rini
b24550accd configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-05 14:11:16 -04:00
Ran Wang
893cdf0b7f configs: powerpc: add usb (host) mass storage support
commit 0cfccb5401 ("configs: Resync with savedefconfig")
removed CONFIG_USB_STORAGE from some powerpc platforms' defconfig
files, whicih would block the use case of system loading rootfs
from USB drives, add them back.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24 08:27:44 -04:00
Hou Zhiqiang
6c9e68e860 configs: P2020RDB: Enable DM_ETH config
Enable the DM_ETH and DM_MDIO config.

On P2020RDB, the eTSEC1 is connecting with a switch VSC7385,
so also enable the fixed PHY support.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24 08:27:44 -04:00
Xiaowei Bao
277507369d configs: P2020RDB: Enable ESPI driver
Enable the DM ESPI driver in P2020RDB defconfig.

Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24 08:27:44 -04:00
Adam Ford
e91907a146 Convert CONFIG_ENV_OVERWRITE to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_OVERWRITE

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28 16:18:06 -04:00
Tom Rini
f7d0ae9c63 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-28 08:46:52 -04:00
Marek Szyprowski
69be8fd164 powerpc: move ADDR_MAP to Kconfig
Move ADDR_MAP related config options from include/configs/*.h to the
proper place in lib/Kconfig. This has been done using
./tools/moveconfig.py and manual inspection of the generated changes.
This is a preparation to use ADDR_MAP helper on ARM 32bit Raspberry Pi4
board for mapping the PCIe XHCI MMIO, which is above the 4GiB identity
mapping limit.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2020-07-10 14:10:43 -04:00
Tom Rini
c5a6e9f8b8 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-06 13:54:25 -04:00
Tom Rini
b11dc33e36 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-08 09:08:39 -04:00
Biwen Li
b36decf81e configs: P2020RDB: enable DM_I2C and DM_RTC
This enables DM_I2C and DM_RTC in P2020RDB defconfigs

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-05-04 09:12:36 +05:30
Tom Rini
5bec37eb72 Merge branch 'migrate-various-PHY-options'
- Finish migration of CONFIG_PHYLIB and a number of related symbols to
  defconfig files.
2020-04-28 16:41:00 -04:00
Tom Rini
556fd590db configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28 16:15:47 -04:00
Tom Rini
306881a0bf Convert CONFIG_PHYLIB et al to Kconfig
This converts the following to Kconfig:
   CONFIG_PHYLIB
   CONFIG_BITBANGMII
   CONFIG_MV88E6352_SWITCH
   CONFIG_MV88E61XX_SWITCH
   CONFIG_PHYLIB_10G
   CONFIG_PHY_AQUANTIA
   CONFIG_PHY_ATHEROS
   CONFIG_PHY_BROADCOM
   CONFIG_PHY_CORTINA
   CONFIG_PHY_DAVICOM
   CONFIG_PHY_ET1011C
   CONFIG_PHY_LXT
   CONFIG_PHY_MARVELL
   CONFIG_PHY_MICREL
   CONFIG_PHY_NATSEMI
   CONFIG_PHY_REALTEK
   CONFIG_RTL8211X_PHY_FORCE_MASTER
   CONFIG_PHY_SMSC
   CONFIG_PHY_TERANETICS
   CONFIG_PHY_TI
   CONFIG_PHY_VITESSE
   CONFIG_PHY_XILINX

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28 15:57:58 -04:00
Tom Rini
052170c6a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22 13:38:00 -05:00
Ran Wang
a8f215a07b configs: P2020: enable CONFIG_DM_USB support
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-23 14:08:27 +05:30
Tom Rini
0cfccb5401 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 17:18:38 -05:00
Miquel Raynal
d4c2f6b7e3 mtd: ensure MTD/the raw NAND core are compiled when there is a NAND flash
Both symbols must be enabled when there is a raw NAND driver
selected. Also enable them when CONFIG_CMD_NAND is selected to avoid
breaking things when we'll further rework the MTD dependency
description.

Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
[trini: Rebase and migrate a few more boards here]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 13:26:17 -05:00
Yinbo Zhu
02504ef07e configs: enable eSDHC device module for P2020RDB board
Enable eSDHC device module for P2020RDB board

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-25 11:54:27 +05:30
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Tom Rini
8d8ee47e03 env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-20 12:24:50 -05:00
Tom Rini
665c35a764 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-23 11:47:37 -04:00
Hou Zhiqiang
7eabbf2512 configs: P2020RDB: Enable PCIe driver
Enable the DM PCIe driver in P2020RDB defconfig.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-28 13:47:46 +05:30
Hou Zhiqiang
caa756975c powerpc: Enable device tree support for P2020RDB
Add device tree for P1020RDB boards and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-26 21:23:22 +05:30
Tom Rini
db4080d56d configs: Migrate the various SPL_BOOT_xxx choices for PowerPC
The non-CONFIG_SPL_FRAMEWORK SPL used on some PowerPC platforms have a
choice between CONFIG_SPL_NAND_BOOT, CONFIG_SPL_MMC_BOOT and
CONFIG_SPL_SPI_BOOT.  Migrate this to Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-14 16:10:49 -04:00
Simon Goldschmidt
f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Patrick Delaunay
14453fbfad Convert CONFIG_SF_DEFAULT_* to Kconfig
This converts the following to Kconfig:
  CONFIG_SF_DEFAULT_BUS
  CONFIG_SF_DEFAULT_CS
  CONFIG_SF_DEFAULT_MODE
  CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25 17:36:53 -04:00