Commit graph

7 commits

Author SHA1 Message Date
Joe Hershberger
16879cd25a net: phy: Don't limit phy addresses by default
Some boards expect to find more than one phy while other boards are old
and need to be limited to a specific phy address. Only limit the phy
address for boards that opt in.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-04-13 15:56:47 -05:00
Stefan Mavrodiev
b30c419040 Move CONFIG_PHY_ADDR to Kconfig
CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).

Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.

After the implemention, moveconfig was run. The issues are:
	- edb9315a	- CONFIG_PHYLIB is not enabled. Entry is
			  deleted.

	- ds414		- CONFIG_PHYLIB is in incompatible format:
			  { 0x1, 0x0 }. This entry is also deleted.

	- devkit3250	- The PHY_ADDR is in hex format (0x1F).
			  Manually CONFIG_PHY_ADDR=31 is added in
			  the defconfig.

After the changes the suspicious defconfigs passes building.

Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13 22:36:33 +05:30
Tom Rini
278b90ce78 configs: Migrate CONFIG_SYS_TEXT_BASE
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11 09:30:09 -05:00
Tuomas Tynkkynen
a4fa811463 cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA
cmd/Makefile has:

ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif

which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant

 # CONFIG_CMD_FPGA is not set

can be removed from board defconfigs that don't actually have an FPGA.

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-05 20:58:11 -05:00
Tom Rini
7af2e3648f configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-12-18 20:19:09 -05:00
Neil Armstrong
c7be3e5a79 ARM: arch-meson: build memory banks using reported memory from registers
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.

But mainline U-Boot and Linux has the old address and size fixed.

These SoCs have a register interface to get the two firmware reserved
memory start and sizes.

This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.

Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].

[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html

Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()

Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception

Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-12-04 10:17:29 -05:00
Neil Armstrong
96e7b5a174 arm: Add LibreTech CC support based on Meson GXL family
This adds platform code for the Libre Computer CC "Le Potato" board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.

This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.

The meson-gxl-s905x-libretech-cc.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2017-12-04 09:59:03 -05:00