This driver implements MAC and MII layer of the ethernet controller.
Network data transfer is handled by controller internal DMA engine.
Ethernet controller is configurable through device-tree file.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
The memac for PHY management on little endian SoCs is similar on big
endian SoCs, so we modify the driver by using I/O accessor function to
handle the endianness, so the driver can be reused on little endian
SoCs, we introduce CONFIG_SYS_MEMAC_LITTLE_ENDIAN for little endian
SoCs, if the CONFIG_SYS_MEMAC_LITTLE_ENDIAN is defined, the I/O access
is little endian, if not, the I/O access is big endian. Move fsl_memac.h
out of powerpc include.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
LDPAA Ethernet driver is a freescale's new ethernet driver based on
Layerscape architecture.
Every ethernet driver controls on DPNI object. Where all DPNIs share
one common DPBP and DPIO object to support Rx and Tx flows.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Cristian Sovaiala <cristian.sovaiala@freescale.com>
CC: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
CC: J. German Rivera <German.Rivera@freescale.com>
[York Sun: s/NetReceive/net_process_received_packet]
Reviewed-by: York Sun <yorksun@freescale.com>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Implement a bridge between U-Boot's network stack and Linux's raw packet
API allowing the sandbox to send and receive packets using the host
machine's network interface.
This raw Ethernet API requires elevated privileges. You can either run
as root, or you can add the capability needed like so:
sudo /sbin/setcap "CAP_NET_RAW+ep" /path/to/u-boot
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic network support to sandbox which includes a network driver.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new driver for the Gigabit Ethernet MAC found on Intel Topcliff
Platform Controller Hub. Tested under 10/100 half/full duplex and 1000
full duplex modes using ping and tftpboot commands.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Greg Ungerer <greg.ungerer@opengear.com>
Acked-by: Marek Vasut <marex@denx.de>
Upgrade Manage Complex (MC) flib API to 0.5.2. Rename directory
fsl_mc to fsl-mc. Change the fsl-mc node in Linux device tree
from "fsl,dprcr" to "fsl-mc". Print MC version info when
appropriate.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds a driver for VSC9953 L2 Switch. This Vitesse IP
is integrated in Freescale T1040 and T1020 SoCs.
The L2 switch has 10 Ethernet ports: 2 internal fixed-links
(ports 8 and 9) at 2.5 Gbps and and 8 external ports at 1 Gbps.
The external ports may be connected to PHYs over QSGMII and SGMII.
Commands have also been added to enable/disable a port and to
check a port's link speed, duplexity and status. The commands are:
ethsw port <port_nr> enable|disable - enable/disable an l2 switch port
ethsw port <port_nr> show - show an l2 switch port's configuration
port_nr=0..9; use "all" for all ports
For more detailse please see doc/README.t1040-l2switch
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support for the NETA ethernet controller which is integrated
in the Marvell Armada XP SoC's. This port is based on the Linux driver which
has been stripped of the in U-Boot unused portions.
Tested on the Marvell MV78460 eval board db-78460-bp.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Tested-by: Luka Perkov <luka@openwrt.org>
The Broadcom StarFighter2 Ethernet driver is used in multiple Broadcom
SoC(s) and:
- supports multiple MAC blocks,
- provides support for the Broadcom GMAC.
This driver requires MII and PHYLIB.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
The following configs are not defined at all:
- CONFIG_INCA_IP_SWITCH
- CONFIG_PBL2800_ETHER
- CONFIG_PHY_ICPLUS
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
There have been 3 versions of the sunxi_emac support patch during its
development. Somehow version 2 ended up in upstream u-boot where as
the u-boot-sunxi git repo got version 3.
This bumps the version in upstream u-boot to version 3 of the patch:
- Initialize MII clock earlier so mii access to allow independent use
- Name change from WEMAC to EMAC to match mainline kernel & chip manual
- Cosmetic code cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Adding support to load and start the Layerscape Management Complex (MC)
firmware. First, the MC GCR register is set to 0 to reset all cores. MC
firmware and DPL images are copied from their location in NOR flash to
DDR. MC registers are updated with the location of these images.
Deasserting the reset bit of MC GCR register releases core 0 to run.
Core 1 will be released by MC firmware. Stop bits are not touched for
this step. U-boot waits for MC until it boots up. In case of a failure,
device tree is updated accordingly. The MC firmware image uses FIT format.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.
Port configurations are defined in board.c.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
The device interface is 16 bits wide.
All the available packets are read from the incoming fifo.
Signed-off-by: Roberto Cerati <roberto.cerati@bticino.it>
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
[voice.shen@atmel.com: address comments from review results]
[voice.shen@atmel.com: clean up for submit]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
This patch adds support for the WEMAC, the ethernet controller included
in the Allwinner A10 SoC. It will get used in the upcoming A10 board
support.
From: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Device driver for Zynq Gem IP.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
CPSW is an on-chip ethernet switch that is found on various SoCs from Texas
Instruments. This patch adds a simple driver (based on the Linux driver) for
this hardware module.
This patch also adds support to clean and flush dcache during packet send
and receive.
Changes by Sandhya: Added support to clean and flush dcache during packet
send/receive and added timeouts.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Satyanarayana, Sandhya <sandhya.satyanarayana@ti.com>
[Ilya: Cleaned cache handling, some style cleanup, some small
fixes, use of internal RAM for descriptors]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Xilinx LocalLink Tri-Mode Ether MAC driver can be
used by Xilinx Microblaze or Xilinx ppc405/440 in
SDMA and FIFO mode. DCR or XPS bus can be used.
The driver uses and requires MII and PHYLIB.
CP: 4 warnings: 'Use of volatile is usually wrong'
I won't fix this, because it depends on the network
driver subsystem.
Reported-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Stephan Linz <linz@li-pro.net>
This adds ethernet driver for Calxeda xgmac found on Highbank SOC.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Fix: WARNING: __aligned(size) is preferred over
__attribute__((aligned(size)))
Signed-off-by: Wolfgang Denk <wd@denx.de>
No one uses this driver, and it isn't converted to the NET_MULTI
framework (which we dropped recently), so drop this driver too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
As a part of the manufacturing process for some of our custom hardware,
we are programming the EEPROMs attached to our Intel 82571EB controllers
from software using U-Boot and Linux.
This code provides several conditionally-compiled features to assist in
our manufacturing process:
CONFIG_CMD_E1000:
This is a basic "e1000" command which allows querying the controller
and (if other config options are set) performing EEPROM programming.
In particular, with CONFIG_E1000_SPI this allows you to display a
hex-dump of the EEPROM, copy to/from main memory, and verify/update
the software checksum.
CONFIG_E1000_SPI_GENERIC:
Build a generic SPI driver providing the standard U-Boot SPI driver
interface. This allows commands such as "sspi" to access the bus
attached to the E1000 controller. Additionally, some E1000 chipsets
can support user data in a reserved space in the E1000 EEPROM which
could be used for U-Boot environment storage.
CONFIG_E1000_SPI:
The core SPI access code used by the above interfaces.
For example, the following commands allow you to program the EEPROM from
a USB device (assumes CONFIG_E1000_SPI and CONFIG_CMD_E1000 are enabled):
usb start
fatload usb 0 $loadaddr 82571EB_No_Mgmt_Discrete-LOM.bin
e1000 0 spi program $loadaddr 0 1024
e1000 0 spi checksum update
Please keep in mind that the Intel-provided .eep files are organized as
16-bit words. When converting them to binary form for programming you
must byteswap each 16-bit word so that it is in little-endian form.
This means that when reading and writing words to the SPI EEPROM, the
bit ordering for each word looks like this on the wire:
Time >>>
------------------------------------------------------------------
... [7, 6, 5, 4, 3, 2, 1, 0, 15, 14, 13, 12, 11, 10, 9, 8], ...
------------------------------------------------------------------
(MSB is 15, LSB is 0).
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Only one board uses this driver (ns9750dev), but the board doesn't seem
to have an entry to actually build it in the Makefile/boards.cfg, so just
delete net support from its board config.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Everyone seems to have converted to the new enc28j60 driver, so drop
this older one which isn't used and doesn't support NET_MULTI.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add axi_ethernet driver for little-endian Microblaze.
RX/TX BDs and rxframe buffer are shared among all axi_ethernet MACs.
Only one MAC can work in one time.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Mike Frysinger <vapier@gentoo.org>
These drivers have never been converted to NET_MULTI, and they are only
used by one board (BMW). So drop the drivers until someone feels like
rewriting them for NET_MULTI support.
Rather than punting the BMW board completely, just disable net support
in its board config. Seems to build fine without it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
This patch adds support for Fast Ethernet Controller driver for
Armada100 series.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block. Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman). However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.
Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely. This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.
Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.
We add support for the following SoCs:
* P1023 - 1 Fman, 2x1g
* P4080 - 2 Fman, each Fman has 4x1g and 1x10g
* P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This converts tsec to use the new PHY Lib. All of the old PHY support
is ripped out. The old MDIO driver is split off, and placed in
fsl_mdio.c. The initialization is modified to initialize the MDIO
driver as well. The powerpc config file is modified to configure PHYLIB
if TSEC_ENET is configured.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
V3: further refinements:
- use priv member instead of container method
- allow setting of MAC address by write_hwaddr method
- avoid shutting down link between commands
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch is required before the upcoming new enc28j60 driver
using SPI framework patch can be applied:
- Move legacy enc28j60.c to enc28j60_lpc2292.c.
- Change Makefile and the two affected boards' definition files.
Tested with ./MAKEALL ARM7 that both boards still compile.
Signed-off-by: Reinhard Meyer<info@emk-elektronik.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Rename all references to kirkwood in mvgbe symbols
throughout the whole codebase.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Rename kirkwood_egiga.* to mvgbe.* and adjust makefile
and #include accordingly.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Designware network driver support added.
This is a Synopsys ethernet controller
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This driver supports the Altera triple speeds 10/100/1000 ethernet
mac.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
