When MPC85xx_PMUXCR_SDHC_WP is set then SDHC controller automatically makes
inserted SD card readonly if GPIO[9] is active.
In some design GPIO[9] pin does not have to be connected to SD card
write-protect pin and can be used as GPIO.
So do not set MPC85xx_PMUXCR_SDHC_WP bit when GPIO[9] is not used for
SDHC_WP functionality.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As written in comment, P2020 has two possible SD switch configurations.
Extend code to detect both of them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Like in all other checks in checkboard() function, do not hang on error.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When env support is disabled then usage of env_init() or env_relocate()
generates linker errors. So do not compile env_init() or env_relocate()
in SPL code when env support is disabled in SPL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is an user-selectable SYS_HAS_ARMV8_SECURE_BASE, which has the
same meaning but is just for the ls1043ardb board. As no in-tree config
uses this, drop it and replace it with something more sophiticated:
ARMV8_PSCI_RELOCATE. This option will then enable the ARMV8_SECURE_BASE
option which is used as the base to relocate the PSCI code (or any code
in the secure region, but that is only PSCI). A SoC (or board) can now
opt-in into having such a secure region by enabling
SYS_HAS_ARMV8_SECURE_BASE. Enable it for the LS1043A SoC, where it was
possible to relocate the PSCI code before as well as on the LS1028A SoC
where there will be PSCI support soon.
Additionally, make ARMV8_PSCI and SEC_FIRMWARE_ARMV8_PSCI exclusive.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_early_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.
[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
If M33 handshake is successful, TPM and DSI panel MUX setting is
done by M33, no need to set them.
If handshake is failed or M33 is not booted, continue the TPM
and DSI panel MUX setting
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update DDR PHY settings to support LPDDR4 mode only by adjusting
DQ VREF ctrl, ODT and pads drive strength.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Found the lposc fuse loading having impact to cpu idle in kernel.
Without the loading in dual boot mode, kernel will hang after idle
for a while.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When M33 is LPAV owner in dual boot, DDR, PCC5, CGC2 won't be reset
during APD reset. So no need to init DDR again after reboot, but need to
reconfigure the PLL4 PFD/PFDDIV/LPAV NIC etc, because kernel may
change or disable some of them.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new ddr script, defconfig for ND
Configure the clock for ND mode
changing A35 to 960MHz for OD mode
Update NIC CLK for the various modes
Introduce clock_init_early/late, late is used after pmic voltage
setting, early is used in the very early stage for upower mu, lpuart and
etc.
Note: NIC runs at 324MHz, 442MHz has some random kernel hang issue with
cpuidle enabled now.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This workaround is not needed on i.MX8ULP proto-1B EVK as board has
fixed the problem. Because we don't support proto-1A any longer,
remove the PMIC settings.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With the correct settings described in the device-tree the PHY settings
in the board init are no longer required. The values are taken from the
linux device tree.
The PHY latency settings are derived from the phy-mode property and the
voltage seetings are done via the regulator.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Marek Vasut <marex@denx.de> # 8MNANOD4-EVK
Reviewed-by: Fabio Estevam <festevam@gmail.com>
LS(1021/1012/1028/1043/1046/1088/2088), LX2160, LX2162
platforms are enabled with JR driver model.
removed sec_init() call from board files.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX8MM/MN/MP/MQ - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
We use 'DEBUG' and not 'CONFIG_DEBUG' tree-wide for debug code that is
left in, and not wrapped by some other regular debugging type print
macro.
Cc: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Use the semihosting_enabled function to determine whether or not to
enable semihosting devices. This allows for graceful fallback in the
event a debugger is not attached.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds support for booting entirely from JTAG while using a
hard-coded RCW. With these steps, it is not necessary to program a
"good" RCW using CodeWarrior. The method here can be performed with any
JTAG adapter supported by OpenOCD, including the on-board CMSIS-DAP
(albeit very slowly).
These steps require LS1046A support in OpenOCD, which was added in [1].
[1] 5b70c1f679/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add reference to doc/board/nxp/ls1046ardb.rst]
This converts the readme for this board to rST. I have tried not to
change any semantics from the original (though I did convert MB to M).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This converts the following to Kconfig:
CONFIG_NORFLASH_PS32BIT
Note that we also attempt to correct the behavior of the code here,
which had been testing for "NORFLASH_PS32BIT" which would never be set,
instead check for the now set "CONFIG_NORFLASH_PS32BIT", which results
in some behavior change.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This CONFIG option is used in one place, so pick a more direct name and
migrate to Kconfig. Rework the code slightly.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Both of these variables are used in a few hard-coded ways to set some
string values or print something to the user. In almost all cases, it's
just as useful to hard-code the value used. The exception here is
printing something closer to correct board name for p1_p2_rdb machines.
This can be done using something from the device tree, but for now
hard-code a non-CONFIG based value instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Add support for ethernet on the imx8mn-ddr4-evk.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Use IS_ENABLED(CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG) to make the code
more readable and fix checkpatch.pl warning
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
As suggested in commit 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") for imx8mm_evk, it is possible to produce
single bootable image via binman. This restores the original behavior in
distros, where only one boot container is used to create target image.
Perform similar adaptions in order to provide single bootable image for
imx8mn-ddr4-evk derivate.
Update documentation to drop additional step of copying u-boot.itb
Fixes: 353dfe4b43 ("imx8mn-ddr4-evk: switch to use binman")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0
LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision.
A0.2 will fix the issue in ROM. But A0.1 we have to workaround
it in SPL by setting LPOSCCTRL BIASCURRENT again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The setting does not have effect because we should set it after
power on the PS16 for NIC AV.
So move it after upower_init which has powered on all PS
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board use IO9 of PCA6416 on LPI2C0 and TPM0 for MIPI DSI MUX and
backlight. However the LPI2C0 and TPM0 are M33 resources, in this
patch we simply access them, but this is a temporary solution.
We will modify it when M33 FW changes to set MIPI DSI panel as default
path and enable backlight after reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 045ecf8992 ("configs: enable DM_ETH support for LS1046ARDB")
resulted in the PCI bus no longer being implicitly enumerated.
However, this is necessary for the fdt pcie fixups to work.
Therefore, similar to commit 8b6558bd41 ("board: ls1088ardb:
transition to DM_ETH"), pci_init() is now called in the board_init()
routine when CONFIG_DM_ETH is active.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
IFC-NOR and QSPI are muxed on SoC.
So disable IFC node in dts if QSPI is enabled or disable QSPI node in dts
in case QSPI is not enabled.
"ifc/nor" will be changed to "memory-controller/nor" in linux. So need to
modify "ifc/nor" to "memory-controller/nor" in fdt_path_offset().
Signed-off-by: Jianpeng Bu <jianpeng.bu@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Commit eb1986804d ("configs: enable DM_ETH support for LS1043ARDB")
resulted in the PCI bus no longer being implicitly enumerated.
However, this is necessary for the fdt pcie fixups to work.
Therefore, similar to commit 8b6558bd41 ("board: ls1088ardb:
transition to DM_ETH"), pci_init() is now called in the board_init()
routine when CONFIG_DM_ETH is active.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
