SPEAr310 SoC support contains basic spear310 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
- emi driver(cfi support)
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr310 and SPEAr320 SoCs contain an EMI controller to interface
Paraller NOR flashes. This patch adds the support for this IP
The standard CFI driver is used to interface with NOR flashes
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr300 SoC support contains basic spear300 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
Signed-off-by: Vipin <vipin.kumar@st.com>
This patch adds the support to read and write mac id from i2c
memory.
For reading:
if (env contains ethaddr)
pick env ethaddr
else
pick ethaddr from i2c memory
For writing:
chip_config ethaddr XX:XX:XX:XX:XX:XX writes the mac id
in i2c memory
Signed-off-by: Vipin <vipin.kumar@st.com>
SPEAr600 SoC support contains basic spear600 support along with the
usage of following drivers
- serial driver(UART)
- i2c driver
- smi driver
- nand driver(FSMC)
- usbd driver
Signed-off-by: Vipin <vipin.kumar@st.com>
When referring to PCIe and USB 'endpoint' is the standard naming
convention.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Remy Bohmer <linux@bohmer.net>
The new board revision has a different LCD.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Give the CF/IDE code its own file to keep things cleanly separated. While
we're here, clean up the code to use common functions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
While the initdram() function makes sense on some arches, it doesn't for
Blackfin systems as it's always implemented the same way.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
USB0_DRVVBUS pinmux configuration is required for USB functinality
in uboot.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Remove PCI reset, if there is a monarch PMC module.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
convert clrbits_be32 + setbits_be32 to clrsetbits_be32, use out_be32 to set gcr.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The caddy2 is a variant of the already supported vme8349. So we just
add the differences to this board port. To better support those two
boards we switched from fixed SDRAM configuration to usage of
spd_sdram(). This is done by providing a board specific SPD EEPROM
routine with different values for both boards.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
changed to use mkconfig -t option instead, plus misc codingstyle fixes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The core support for NAND booting is there already, so this patch
is pretty straightforward.
There is one trick though: top level Makefile expects nand_spl to
be in nand_spl/board/$(BOARDDIR), but we can fully reuse the code
from mpc8313erdb boards, and so to not duplicate the code we just
symlink nand_spl/board/freescale/mpc8315erdb to mpc8313erdb.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
o silence make during ln echo
o update documentation
o and avoid:
$ ./MAKEALL MPC8315ERDB_NAND
Configuring for MPC8315ERDB board...
sdram.o: In function `fixed_sdram':
/home/r1aaha/git/u-boot/nand_spl/board/freescale/mpc8313erdb/sdram.c:72: undefined reference to `udelay'
by renaming udelay -> __udelay in the spirit of commit
3eb90bad65 "Generic udelay() with watchdog
support".
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Thanks to "Errata to MPC8569E PowerQUICC III Integrated Host Processor
Family Reference Manual, Rev. 0" document, which describes all eSDHC
pins, we can add 4-bits eSDHC support for MPC8569E-MDS boards.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We already map the page cache-inhibited. There is no reason we
shouldn't also be marking it guarded to prevent speculative accesses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rather than hard coding which TLB entry the FLASH is mapped with we can
use find_tlb_idx to determine the entry.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can use fsl_setup_hose to determine if we are a agent/end-point or
a host. Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can use fsl_setup_hose to determine if we are a agent/end-point or
a host. Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can use fsl_setup_hose to determine if we are a agent/end-point or
a host. Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can use fsl_setup_hose to determine if we are a agent/end-point or
a host. Rather than using some SoC specific register we can just look
at the PCI cfg space of the host controller to determine this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use new fsl_pci_init_port() that reduces amount of duplicated code in the
board ports, use IO accessors and clean up printing of status info.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Davinci: Table driven pinmux configuration
Add code to allow pinmux_config tables to be grouped and configured
as a single resource. This removes multiple calls to the pinmux
configuration code from board_init and allows pinmuxes to be
individually configured and added by data manipulation only.
All related #ifdefs can the be removed from board_init code and
since the compiler optimises away statics, #ifdefs can be reduced in
the data definitions as well.
Signed-off-by: Nick Thompson <nick.thompson@gefanuc.com>
These regulators are not needed to start the kernel and only
cause "incomplete constraints" warnings from kernel, so don't
turn them on to save power.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Not all boards have both LEDs hooked, so enabling both on
boards with single LED will just waste power. Make it
possible to choose LEDs by adding argument to
twl4030_led_init().
Using this turn on only LEDB for pandora, leave both LEDs
on for all other boards, as it was before this patch.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
commit eb5eb2b0f7
ppc4xx: Cleanup PPC4xx I2C infrastructure
This patch cleans up the PPC4xx I2C intrastructure:
- Use C struct to describe the I2C registers instead of defines
- Coding style cleanup (braces, whitespace, comments, line length)
- Extract common code from i2c_read() and i2c_write()
- Remove unneeded IIC defines from ppc405.h & ppc440.h
breaks comiling for the KAREF and METROBOX boards.
This patch fixes this issue.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Prototype for gunzip/zunzip was only in lib_generic/gunzip.c and thus
repeated in every file using it. This patch moves the prototypes to
common.h and removes all prototypes distributed anywhere else.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
The preferred serial output comes from the debug board.
When the debug board is disconnected, fall back on using
usbtty from the usb connector on the Zoom2 board.
This shows up as /dev/ttyACM0 in a linux host.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
A previous Commit converted the LAN91C96 Ethernet driver to using the
CONFIG_NET_MULTI API, but did not include full board support. This patch
finishes the job.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This modification is NOT tested on any of the
platforms modified as I dont have them. please
help by testing+building+fixing
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Enable the NET MULTI option and remove build warning
Tested: SDP3430
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
u-boot updates, before starting Linux, the memory node in the
DTS. As this is a "standard" feature, move this functionality
to the cpu.c file for mpc5xxx and mpc512x processors.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch introduces a weak default function for post_hotkey_pressed(),
returning 0, for boards without hotkey support. The long-running tests
won't be started on those boards. This default function was implemented
in many board directories. By implementing this weak default we can
remove all those duplicate versions.
Boards with hotkey support, can override this weak default function
by defining one in their board specific code.
Signed-off-by: Stefan Roese <sr@denx.de>
