ls2085a_common.h contains hard-coded information for NOR/NAND flash,
I2C, DDR, etc. These are platform specific. Move them out of common
header file and placed into respective board header files.
Move TEXTBASE to 1MB offset to fit NOR flash with up to 1MB sector
size.
Enable command auto complete. Update prompt symbol. Set fdt_high to
0xa0000000 because Linux requires that the fdt be 8-byte aligned
and below 512 MiB. Besides ensuring compliance with the 512 MiB
limit, this avoids problems with the dtb being misaligned within
the FIT image.
Change the MC FW, MC DPL and Debug server NOR addresses in compliance
with the NOR flash layouts for 128MB flash.
Add PCIe macros. Enable "loadb" command. Disable debug server.
Enable workaround for erratum A008511.
Stop reset on panic for postmortem debugging.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Generic Timer may contain an erroneous value. The workaround is to
read it twice until getting the same value.
Signed-off-by: York Sun <yorksun@freescale.com>
LDPAA Ethernet driver is a freescale's new ethernet driver based on
Layerscape architecture.
Every ethernet driver controls on DPNI object. Where all DPNIs share
one common DPBP and DPIO object to support Rx and Tx flows.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Cristian Sovaiala <cristian.sovaiala@freescale.com>
CC: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
CC: J. German Rivera <German.Rivera@freescale.com>
[York Sun: s/NetReceive/net_process_received_packet]
Reviewed-by: York Sun <yorksun@freescale.com>
Switch to CONFIG_ARCH_INTEGRATOR defined by Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Select integrator boards by the combination of platform select (AP/CP)
and core module select (CM720T, CM920T, ...).
This allows us to remove CONFIG_SYS_EXTRA_OPTIONS and make Kconfig
much cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
The board/SoC select menu in arch/arm/Kconfig is still cluttered.
Add ARCH_INTEGRATOR into arch/arm/Kconfig and move the board select
under arch/arm/mach-integrator.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
arch/arm/cpu/arm720t/start.S includes <asm/arch/hardware.h>,
but the hardware.h headers of ARM720T boards are all empty.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
For some files I neglected to add a license. Rectify this:
arch/arm/dts/exynos4210-pinctrl-uboot.dtsi
arch/arm/dts/exynos4x12-pinctrl-uboot.dtsi
arch/arm/dts/exynos5250-pinctrl-uboot.dtsi
arch/arm/dts/exynos54xx-pinctrl-uboot.dtsi
arch/arm/dts/s5pc100-pinctrl.dtsi
arch/arm/dts/s5pc110-pinctrl.dtsi
This file came from Linux and has no license information there, so add a
comment to that effect:
arch/sandbox/include/asm/bitops.h
This file also came from Linux - presumably someone from TI could add the
license:
include/dt-bindings/pinctrl/omap.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Ingrid Viitanen <ingrid.viitanen@nokia.com>
Add the initial SPL support for HummingBoard-i2eX, which is based on a
MX6 Dual.
For more information about HummingBoard, please check:
http://www.solid-run.com/products/hummingboard/
Based on the work from Jon Nettleton and Rabeeh Khoury.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
DDR3 has a special Precharge power-down mode: fast-exit vs slow-exit.
In slow-exit mode the DLL is off but in some quiescent state that makes it easy
to turn on again in tXPDLL cycles (about 10tCK) vs the full tDLLK (512tCK).
In fast-exist mode the DLL is maintained such that it is ready again in about
3tCK.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reading the boot mode pins after power-up does not necessarily represent the
boot mode used by the ROM loader. For example the state of a pin may have
changed because a recovery switch which was pressed to enter USB mode is
already released after plugging in USB.
The ROM loader stores the value a fixed address in OCRAM. Use this value
instead of reading the boot map pins.
The GLOBAL_BOOT_MODE_ADDR for i.MX28 is taken from an U-Boot patch for the
MX28EVK:
http://repository.timesys.com/buildsources/u/u-boot/u-boot-2009.08/u-boot-2009.08-mx28-201012211513.patch
Leave the boot mode detection for the i.MX23 untouched. Someone has to test
whether the i.MX ROM loader does also store the boot mode in OCRAM and if the
address match.
This patch superseeds my incorrect patch:
ARM: mxs: get boot mode from OTP
http://patchwork.ozlabs.org/patch/454930/
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Cc: Stefano Babic <sbabic@denx.de>
Freescale's Layerscape Management Complex (MC) provide support various
objects like DPRC, DPNI, DPBP and DPIO.
Where:
DPRC: Place holdes for other MC objectes like DPNI, DPBP, DPIO
DPBP: Management of buffer pool
DPIO: Used for used to QBMan portal
DPNI: Represents standard network interface
These objects are used for DPAA ethernet drivers.
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Cristian Sovaiala <cristian.sovaiala@freescale.com>
Signed-off-by: pankaj chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds description for NOR flash layout (firmware images)
in the README file for LS2085A platforms.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Debug Server driver is responsible for loading the Debug
server FW on the Service Processor (Cortex-A5 core) on LS2085A like
SoCs and then polling for the successful initialization of the same.
TOP MEM HIDE is adjusted to ensure the space required by Debug Server
FW is accounted for. MC uses the DDR area which is calculated as:
MC DDR region start = Top of DDR - area reserved by Debug Server FW
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Muram will power off during deepsleep, and the microcode of qe
in muram will be lost, it should be reload when resume.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch uses the common function name ft_pci_setup to replace
ft_pcie_setup, then removes unnecessary pcie_layerscape.h because
all the functions have been declared in common.h.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <yorksun@freescale.com>
1. Default environment will be used for secure boot flow
which can't be edited or saved.
2. Command for secure boot is predefined in the default
environment which will run on autoboot (and autoboot is
the only option allowed in case of secure boot) and it
looks like this:
#define CONFIG_SECBOOT \
"setenv bs_hdraddr 0xe8e00000;" \
"esbc_validate $bs_hdraddr;" \
"source $img_addr;" \
"esbc_halt;"
#endif
3. Boot Script can contain esbc_validate commands and bootm command.
Uboot source command used in default secure boot command will
run the bootscript.
4. Command esbc_halt added to ensure either bootm executes
after validation of images or core should just spin.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For LS102xA, some workarounds are only used in VER1.0, so silicon
version detection are added for QDS and TWR boards.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since the SoCFPGA SDRAM support is not yet applied to u-boot, we still
need to be able to compile the codebase. Introduce stub functions which
temporarily supplement the missing SDRAM setup functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Remap SDRAM to 0x0, and clear OCRAM's ECC in board_init_f().
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Reviewed-by: Marek Vasut <marex@denx.de>
For SoCFGPA, use the common ARMv7 lowlevel_init. Thus, we can delete the
SoCFPGA lowlevel_init.S file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the calls in the spl_board_init to enable SDRAM, timer, and UART.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
These functions will be needed for use by the SPL for enabling the
console and sdram initialization.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
the ldb clock can be setup in board code (for example set through PLL5).
Update the ldb_clock rate also through board code.
This should be removed, if a clock framework is availiable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Don't store it in a u32.
Don't dereference the bus address as if it were a virtual address
(fixes 284231e49a ("ahci: Support splitting of read transactions
into multiple chunks")).
Fixes crash on boot in MPC8641HPCN_36BIT target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Vadim Bendebury <vbendeb@chromium.org>
Acked-by: York Sun <yorksun@freescale.com>
Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1:
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
All the Zynq boards have switch to Driver Model.
"select DM" is better than default value in each defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
All the UniPhier boards have switch to Driver Model.
"select DM" is better than default value in each defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
As mentioned in the previous commit, adding default values in each
Kconfig causes problems because it does not co-exist with the
"depends on" syntax. (Please note this is not a bug of Kconfig.)
We should not do so unless we have a special reason. Actually,
for CONFIG_DM*, we have no good reason to do so.
Generally, CONFIG_DM is not a user-configurable option. Once we
convert a driver into Driver Model, the board only works with Driver
Model, i.e. CONFIG_DM must be always enabled for that board.
So, using "select DM" is more suitable rather than allowing users to
modify it. Another good thing is, Kconfig warns unmet dependencies
for "select" syntax, so we easily notice bugs.
Actually, CONFIG_DM and other related options have been added
without consistency: some into arch/*/Kconfig, some into
board/*/Kconfig, and some into configs/*_defconfig.
This commit prefers "select" and cleans up the following issues.
[1] Never use "CONFIG_DM=n" in defconfig files
It is really rare to add "CONFIG_FOO=n" to disable CONFIG options.
It is more common to use "# CONFIG_FOO is not set". But here, we
do not even have to do it.
Less than half of OMAP3 boards have been converted to Driver Model.
Adding the default values to arch/arm/cpu/armv7/omap3/Kconfig is
weird. Instead, add "select DM" only to appropriate boards, which
eventually eliminates "CONFIG_DM=n", etc.
[2] Delete redundant CONFIGs
Sandbox sets CONFIG_DM in arch/sandbox/Kconfig and defines it again
in configs/sandbox_defconfig.
Likewise, OMAP3 sets CONFIG_DM arch/arm/cpu/armv7/omap3/Kconfig and
defines it also in omap3_beagle_defconfig and devkit8000_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since we can support both controllers now, enable this in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Convert Exynos boards over to use driver model for USB. This does not remove
any unnecessary code so far.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These are needed to enable the USB bus (although not sufficient since it
still does not work).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add QSPI controller dts node in ls1021a.dtsi.
Add QSPI slave device dts node in ls1021a-twr.dts and ls1021a-qds.dts.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Update DSPI controller node in ls1021a.dtsi.
Update flash device node in ls1021a-qds.dts.
Ls1021a-twr board doesn't support DSPI, so remove DSPI node
in ls1021a-twr.dts.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Change address_cells and size_cells of root node and 'soc' node
from 2 to 1.
We backport ls1021a device tree source files from kernel to u-boot.
Kernel files set address_cells and size_cells to 2 in order to access
more than 4GB space.
But we don't have this requirement now and u-boot fdtdec_get_xxx interfaces
can't support property whose size is 'u64' completely.
So make this change.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Bring in required device tree files for ls1021a from Linux.
These are initially unchanged and have a number of pieces not needed by U-Boot.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Backport of kernel commits:
7c14f6c719de092d69c81877786e83ce7ae1a860
35faad2a1563b3d4dc983a82ac41033fe053870c
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
The U-Boot device trees are slightly different in a few places. Adjust them
to remove most of the differences. Note that U-Boot does not support the
concept of interrupts as distinct from GPIOs, so this difference remains.
For sandbox, use the same keyboard file as for ARM boards and drop the
host emulation bus which seems redundant.
Signed-off-by: Simon Glass <sjg@chromium.org>
This value is not used by the network stack and is available in the
global data, so stop passing it around. For the one legacy function
that still expects it (init op on old Ethernet drivers) pass in the
global pointer version directly to avoid changing that interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(Trival fix to remove an unneeded variable declaration in 4xx_enet.c)
In the case where the arch defines a custom map_sysmem(), make sure that
including just mapmem.h is sufficient to have these functions as they
are when the arch does not override it.
Also split the non-arch specific functions out of common.h
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit d3cfcb3 (ARM: DRA7: Enable clocks for USB OTGSS and USB PHY)
changed the member names of prcm_regs from cm_l3init_usb_otg_ss_clkctrl
to cm_l3init_usb_otg_ss1_clkctrl and from cm_coreaon_usb_phy_core_clkctrl
to cm_coreaon_usb_phy1_core_clkctrl in order to differentiate between
the two dwc3 controllers present in dra7xx/am43xx and enabled these
clocks in enable_basic_clocks() in hw_data.c. However these clocks
continued to be enabled in board files/driver files for dwc3 host
mode functionality causing compilation break with few configs.
Fixed it here by making all the clocks enabled in enable_basic_clocks()
and removing it from board files/driver files here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The TTBR0 register and Table Descriptors of the ARMv7 TLB weren't being
properly set to allow for the configuration specified caching modes to
be active over DRAM. This commit fixes those issues.
Signed-off-by: Bryan Brinsko <bryan.brinsko@rockwellcollins.com>
This enables ARMv7 barrier operations support when
march=armv7-a is enabled.
Using CP15 barriers causes U-Boot bootm command crash when
transferring control to the loaded image on Renesas R8A7794 Cortex A7 CPU.
Using ARMv7 barrier operations instead of the deprecated CP15 barriers
helps to avoid these issues.
Signed-off-by: Valentine Barshak <valentine.barshak+renesas@cogentembedded.com>
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Linux-arm64 require that CNTVOFF_EL2 should be programmed with
a consistent value on all cpus. Initializing CNTVOFF_EL2 at state
transition instead of start.S could prevent potential different value
on cpus if ATF exist and u-boot runs at only one cpu.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
This commit copies implementation of the find_next_zero_bit() from
git://git.denx.de/u-boot.git/arch/mips/include/asm/bitops.h. v2014.07
The function is required to enable MCAST_TFTP support for ARM platforms.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Sunxi platforms come with at least 3 TWI (I2C) controllers and some platforms
even have up to 5. This adds support for every controller on each supported
platform, which is especially useful when using expansion ports on single-board-
computers.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Orion5x, Kirkwood and Armada XP platforms come with a single TWSI (I2C) MVTWSI
controller. However, other platforms using MVTWSI may come with more: this is
the case on Allwinner (sunxi) platforms, where up to 4 controllers can be found
on the same chip.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When u-boot boots the board may be powering vbus, we turn off vbus in
sunxi_usbc_request_resources, if we are too quick with reading vusb-detect
after this we may see a residual charge and assume we've an external vusb
connected even though we do not. So when we see an external vusb wait a bit
and try again.
Without this when dealing with a pmic controller vbus and doing "reset" on
the u-boot console the musb host will only init once every other boot, because
the other boot it thinks an external vbus is present, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On boards which use the pmic to enable/disable vbus on the otg port, the
vbus value is not reset to 0 on reset, as reset only resets the SoC and not
the pmic, so explicitly set vbus to 0 on init (request_resources) by moving
the gpio_direction_output call into request_resources.
For consistency also move the gpio_direction_input call for vbus-detect into
request_resources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Sunxi platforms have different possible mmc pin mux setups (except for mmc0),
which are different across platforms.
This lets users configure which is used through the CONFIG_MMC*_PINS Kconfig
options. This is especially relevant when a second (in addition to mmc0) port
is used and CONFIG_MMC_SUNXI_SLOT_EXTRA is enabled.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Each hardware feature exposed through the GPIO pin mux is usually using the same
function index (for a given port), so there is no need to define one value per
pin: one value per hardware feature per port is sufficient, avoids duplication
and makes everything easier to understand.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
VBUS detection could be needed not only by the musb code (to prevent host mode),
but also by e.g. gadget drivers to start only when a cable is connected.
In addition, this allows more flexibility in vbus detection, as it could easily
be extended to other USBC indexes. Eventually, this would help making musb
support independent from a hardcoded USB controller index (0).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
VBUS detection and enable is now be used with virtual AXP GPIOs, so all the USB
code has to use GPIO in every case and let sunxi_gpio do the heavy lifting.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This converts the VBUS detection and enable logic to GPIO instead of separate
axp functions and checks that have to be used aside usual GPIO functions.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in am43xx board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Implemented board_usb_init(), board_usb_cleanup() and
usb_gadget_handle_interrupts() in dra7xx board file that
can be invoked by various gadget drivers.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added resource_size_t type in order to get rid of the following
compilation error whiel building dwc3 gadget.
include/linux/ioport.h:19:2: error: unknown type name ‘resource_size_t’
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Added dma_free_coherent corresponding to the dma_alloc_coherent in
dma-mapping.h in order to free memory allocated using dma_alloc_coherent.
This API is used in dwc3 driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Fixed the following warning here.
"warning: ‘dma_alloc_coherent’ defined but not used" while compiling
udc-core
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled clocks for dwc3 controller and USB PHY present in AM43xx.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Enabled clocks for dwc3 controller and USB PHY present in DRA7.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
When we communicate with the VideoCore to perform property mailbox
transactions, that is a DMA operation as far as the property buffer
is concerned. Use phys_to_bus() on that buffer.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
The BCM283[56] contain both a L1 and L2 cache between the GPU (a/k/a
VideoCore CPU?) and DRAM. DMA-capable peripherals can also optionally
access DRAM via this same L2 cache (although they always bypass the L1
cache). Peripherals select whether to use or bypass the cache via the
top two bits of the bus address.
An IOMMU exists between the ARM CPU and the rest of the system. This
controls whether the ARM CPU's accesses use or bypass the L1 and/or L2
cache. This IOMMU is configured/controlled exclusively by the VideoCore
CPU.
In order for DRAM accesses made by the ARM core to be coherent with
accesses made by other DMA peripherals, we must program a bus address
into those peripherals that causes the peripheral's accesses to use the
same set of caches that the ARM core's accesses will use.
On the RPi1, the VideoCore firmware sets up the IOMMU to enable use of
the L2 cache. This corresponds to addresses based at 0x40000000.
On the RPi2, the VideoCore firmware sets up the IOMMU to disable use of
the L2 cache. This corresponds to addresses based at 0xc0000000.
This patch implements U-Boot's phys_to_bus/bus_to_phys APIs according
to those rules.
For full details of this setup, please see Dom Cobley's description at:
http://lists.denx.de/pipermail/u-boot/2015-March/208201.htmlhttp://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/215038https://www.mail-archive.com/u-boot@lists.denx.de/msg166568.html
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Since commit 79d75d7527 (ARM: move -march=* and -mtune= options to
arch/arm/Makefile), all the Tegra boards are broken because the SPL
is built for ARMv7.
Insert Tegra-specific code to arch/arm/Makefile to set compiler
flags for an earlier ARM architecture.
Note:
The v1 patch for commit 79d75d7527 *was* correct when it was
submitted. Notice it was originally written for multi .config
configuration where Kconfig set CONFIG_CPU_V7/CONFIG_CPU_ARM720T for
Tegra U-Boot Main/SPL, respectively. But, until it was merged into
the mainline, commit e02ee2548a (kconfig: switch to single .config
configuration) had been already applied there.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Stephen Warren <swarren@nvidia.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Patch e11c6c27 (arm: Allow lr to be saved by board code) introduced
a different method to return from save_boot_params(). The SPL support
for AXP has been pulled and changing to this new method is now
required for SPL to work correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Work_92105 from Work Microwave is an LPC3250-
based board with the following features:
- 64MB or 128MB SDR DRAM
- 1 GB SLC NAND, managed through MLC controller.
- Ethernet
- Ethernet + PHY SMSC8710
- I2C:
- EEPROM (24M01-compatible)
- RTC (DS1374-compatible)
- Temperature sensor (DS620)
- DACs (2 x MAX518)
- SPI (through SSP interface)
- Port expander MAX6957
- LCD display (HD44780-compatible), controlled
through the port expander and DACs
This board has SPL support, and uses the LPC32XX boot
image format.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
The controller's Reed-Solomon ECC hardware is
used except of course for raw reads and writes.
It covers in- and out-of-band data together.
The SPL framework is supported.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Add support for Inverse Path USB armory board, an open source
flash-drive sized computer based on Freescale i.MX53 SoC.
http://inversepath.com/usbarmory
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Chris Kuethe <chris.kuethe@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
Move the MX5 based boards to arch/arm/cpu/armv7/mx5, following the
commit: 89ebc82137
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Chris Kuethe <chris.kuethe@gmail.com>
Back in fc46bae a "clean up" was introduced that intended to reconcile
some of the AM335x codepaths based on how AM43xx operates.
Unfortunately this introduced a regression on the DDR2 platforms. This
was un-noticed on DDR3 (everything except for Beaglebone White) as we
had already populated sdram_config correctly in sequence. This change
brings us back to the older behavior and is fine on all platforms.
Tested on Beaglebone White, Beaglebone Black and AM335x GP EVM
Reported-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add backlight enable GPIO, and delay needed for panel powerup
via FIMD DT node.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Now that parade driver supports reading SLP and RST GPIO
from DT, specify the same in parade DT node.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Now that the exynos_fb driver supports handling backlight GPIO
via DT, specify pwm output property via FIMD DT node.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The existing setting for rpll_sdiv generates 70.5Mhz RPLL
video clock to drive 1366x768 panel on peach_pit.
This clock rate is not sufficient to drive 1920x1080 panel on peach-pi.
So, we adjust rpll_sdiv to 3 so that it generates 141Mhz pixel clock
which can drive peach-pi LCD.
This change doesn't break peach-pit LCD since 141/2=70.5Mhz, i.e FIMD
divider at IP level will get set to 1(the required divider setting
will be calculated and set by exynos_fimd_set_clock()) and hence
peach-pit LCD still works fine.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add get_lcd_clk and set_lcd_clk callbacks for Exynos5800 needed by
exynos video driver.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Commit 2e82e92526 'Exynos: Clock: Cleanup
soc_get_periph_rate' introduced a bug in I2C config. This patch makes cros_ec
keyboard working again on Samsung Chromebook (snow).
Changes in V2: reorder lines as requested by Joonyoung Shim.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Simon Glass <sjg@chroimum.org>
Tested-by: Simon Glass <sjg@chroimum.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Supports boot up from NAND flash with software ECC eanbled.
And supports boot up from SD/MMC card with FAT file system.
As the boot from SD/MMC card with FAT file system, the BSS
segment is too big to fit into SRAM, so, use the lds to put
it into SDRAM.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Config MCKR according to the datasheet sequence, or else it
will cause the MCKR configuration failed.
Remove timeout checking for clock configuration, if configure
the clock failed, let the system hang while not run in wrong
clock configuration.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
To facilitate changing lowlevel_init to become s_init, move the current
contents of s_init into board_init_f and add the rest of what
board_init_f does here.
In order to compile clean without CONFIG_SKIP_LOWLEVEL_INIT set, leave an
empty stub of s_init(). It can be removed when lowlevel_init becomes s_init.
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Matt Porter <mporter@konsulko.com> on sama5d3_xplained
Signed-off-by: Tom Rini <trini@ti.com>
[rebased on current master, leave s_init() as empty stub]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The commit 8dfafdd (Introduce common timer functions), add common
timer functions, we can use them directly.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[rebase on current master]
Sigend-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Even the 8-bit case needs KBCB configured, as pin D7 is located in this
pingroup.
Please note that pingroup ATC seems to come out of reset with its
config set to NAND so one needs to explicitly configure some other
function to this group in order to avoid clashing settings which is
outside the scope of this patch.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
A while ago I got Russell to change the machine type of our Colibri T20
from COLIBRI_TEGRA2 to COLIBRI_T20 which at least in parts is also
reflected in his machine registry:
http://www.arm.linux.org.uk/developer/machines/list.php?id=3323
For us it is really very beneficial to actually still be able to boot
downstream L4T kernel with its working hardware accelerated
graphics/multimedia stack albeit it being proprietary/closed-source.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In accordance with our other modules supported by U-Boot and as agreed
upon for Apalis/Colibri T30 get rid of the carrier board in the board/
configuration/device-tree naming.
While at it also bring the prompt more in line with our other products.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This allows selection between CSI and DSI_B on the MIPI pads.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Some pinmux controls are in a different register set. Add support for
manipulating those in a similar way to existing pins/groups.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move struct pmux_pingrp_desc type and tegra_soc_pingroups variable
declaration together with other pin/mux level definitions. Now the whole
file is grouped/ordered pin/mux-related then drvgrp-related definitions.
Fix typo in ifdef comment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Patches that added the Tegra210 pinctrl driver and renamed directories
arch/arm/cpu/tegra{$soc}-common -> arch/arm/mach-tegra/tegra-${soc}
crossed. Move the Tegra210 pinctrl driver to the correct location. This
wasn't detected since Tegra210 support is in the process of being added,
and isn't buildable yet.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
make the CPU clock selectable via Kconfig
this removes the sunxi specific CONFIG_CLK_FULL_SPEED defined in each
soc header and replaces it's use in board/sunxi/board.c with
CONFIG_SYS_CLK_FREQ from Kconfig which allows us to configure board
specific frequency on boot
Signed-off-by: Iain Paton <ipaton0@gmail.com>
[hdegoede@redhat.com s/CONFIG_SYS_CLK_FREQ/CONFIG_TIMER_CLK_FREQ/ for the
arch-timer clk speed on sun7i to fix mis-compile on sun7i]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
clock_set_pll1 would pick the next highest available cpu clock speed if
a value not in the pre defined table was selected. this potentially
results in overclocking the soc.
reverse the selection method so that we select the next lowest speed
and add the missing 912Mhz setting that's requested by sun7i which also
uses the sun4i clock code.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The usb0 / otg phy on sunxi boards has a bug where it wrongly detects a
high speed squelch on usb reset deassert when a lo speed device is plugged in.
The android kernel has a work around for this in the form of temporary
disabling the phy's squelch detection on reset deassert, this commit adds
the same workaround to the u-boot sunxi musb code, thereby fixing various usb
lo speed devices not working.
Tested with a (before non working) usb keyboard and a usb 2.4 GHz wireless
keyboard/mouse combo receiver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that loading files using semihosting can be done using
a command in standard scripts, and we have rewritten the boardfile
and added it to the Vexpress64, let's delete the external
interface to the semihosting file retrieveal and rely solely
on these commands, and staticize them inside that file so the
whole business is self-contained.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of sprinkling custom code and calls over the Vexpress64
boardfile, create a command that loads images using semihosting
just like we would load from flash memory of over the network,
using a special command:
smhload <image> <address>
This will make it possible to remove some custom calls and
code and make the boot easier.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The semihosting trap call does not like being inlined, probably
because that will mean register reordering screwing up the return
value in r0, so tag this function "noinline".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
BCM2835 (used on Raspberry Pi) and BCM2836 (used on Raspberry Pi 2)
are similar enough. One of the biggest differences is the ARM
processor. It is reasonable to collect the source files into a
single place, arch/arm/mach-bcm283x/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
This option has a bool type, not hex.
Fix it and enable it if CONFIG_DM is on because Driver Model always
requires malloc memory. Devices are scanned twice, before/after
relocation. CONFIG_SYS_MALLOC_F should be enabled to use malloc
memory before relocation. As it is board-independent, handle it
globally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
The default value of CONFIG_SYS_MALLOC_F_LEN is defined by ./Kconfig
as 0x400. Each defconfig or Kconfig need not repeat the same value.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Robert Baldyga <r.baldyga@samsung.com>
Move the option to Kconfig renaming it to CONFIG_HAVE_GENERIC_BOARD.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
My main motivations for this commit are:
[1] Follow the arch/arm/Makefile style of Linux Kernel
[2] Maintain compiler options systematically
Currently, we give -march=* and -mtune=* options inconsistently:
Only some of the CPUs pass -march=* and -mtune=* options.
By collecting such options into the single place arch/arm/Makefile
we can tell which options are missing at a glance.
[3] Prepare for deprecating arch/*/cpu/*/config.mk
Note:
This commit just moves the compiler options so as not to change
the behavior at all. It does not care about the correctness of
the given options. Fox example, "-march=armv5te" might be better
than "-march=armv4" for ARM946EJS, but it is beyond the scope this
commit. Also, filling the missing -march=* and -tune=* is left
to follow-up patches.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Allocate memory space for pre-allocation malloc and zero global data.
This code is partly from crt0.S.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: "David Müller" <d.mueller@elsoft.ch>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Torsten Koschorrek <koschorrek@synertronixx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Łukasz Majewski <l.majewski@samsung.com>
The callee (arch/arm/lib/cache-cp15.c) has a #ifdef
CONFIG_SYS_DCACHE_OFF conditional. The same conditional in the
caller (arch/arm/mach-uniphier/cache_uniphier.c) is redundant.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The L2 cache is used as a temporary SRAM on SPL.
Now the secondary CPUs store the necessary code for jumping to
Linux on their L1 I-caches. So, the L2 cache can be disabled
much earlier, at the very entry of U-Boot proper (lowlevel_init).
This makes the boot sequence clearer.
Also, as the L1 cache has been disabled by the start.S,
enable_caches() does not need to do it again.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, the secondary CPU(s) are kicked three times:
Boot ROM ---(kick)--> SPL ---(kick)--> U-boot ---(kick)--> Linux.
It makes the boot sequence very complicated.
This commit merges the first and the second kicks, so the secondary
CPU(s) can directly jump from SPL to Linux.
arch/arm/mach-uniphier/smp.S is no longer necessary.
Linux boot test passed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
To remove the ifdef conditional of CONFIG_SKIP_LOWLEVEL_INIT,
add late_lowlevel_init.S to U-Boot proper.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Ifdef conditionals for CONFIG options are not Kconfig-friendly.
Instead, define CONFIG_SPL_STACK to prepare for Kconfig moves.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable CONFIG_SPL_DM and CONFIG_SPL_SERIAL_SUPPORT, which provide
Driver Model UART support on SPL.
CONFIG_SYS_SPL_MALLOC_{START,SIZE} should be dropped because simple
malloc is preferred on SPL. Dlmalloc requires some static variables
on .data section that is not available yet for NOR boot mode etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The UniPhier platform is going to enable Driver Model and UART
support on SPL. Move UART pin settings to early_pin_init(),
which is called from SPL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since we do not have OF_CONTROL support for SPL, platform devices
are necessary to enable Driver Model on SPL.
To prepare for that, move platdevice.o to SPL and enable it by
CONFIG_SPL_DM.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The two Makefiles arch/arm/mach-uniphier/{ph1-ld4,ph1-sld8}/Makefile
are completely the same. We can improve the maintainability by
having one to include the other.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit a86ac9540e (ARM: UniPhier: include <mach/*.h> instead
of <asm/arch/*.h>), UniPhier platform does not need the symbolic
link arch/arm/include/asm. This option is not necessary either.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add basic SECO MX6Q/uQ7 board support (Ethernet, UART, SD are supported).
It also adds a Kconfig skeleton to later add more SECO board (supporting
SoC and board variants).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
IMX_CONFIG is currently passed via the SYS_EXTRA_OPTIONS which is marked
as deprecated.
Add a new Kconfig file under arch/arm/imx-common and define the
IMX_CONFIG Kconfig in there.
Each board is supposed to provide a default value pointing to the
appropriate imximage.cfg file.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Freescale boards are currently all defined in arch/arm/Kconfig, which
makes them hard to detect.
Moreover the MX6 SoC variant (Q, D, DL, S, SL) selection is currently
done via the SYS_EXTRA_OPTIONS option which marked as deprecated.
Move to a more standard way to select sub-architecture and board by
creating a Kconfig under arch/arm/cpu/armv7/mx6 and a new ARCH_MX6
option.
Existing MX6 board definitions should be moved in this new Kconfig in
choice menu, and new boards should be directly declared in this menu.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
