The Jaguar2 SOC family has 63 gpio pins therefore I extended mscc-common
to support new numbe of pins and remove any platform dependency from
mscc-common.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
With the new mscc_bb_spi.c driver, there is no longer use for the
gpio-mscc-bitbang-spi.c driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Thes patch change the luton base device tree to use the newly added
SPI bitbang driver.
It also updates the "mscc_luton_defconfig" to use the new driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch add a new SPI driver for MSCC SOCs that does not sport the
designware SPI hardware controller.
Performance gain: 7.664 seconds vs. 17.633 for 1 Mbyte write.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Do not build write support, unless it's enabled.
In the SPL case, this change will typically remove
precious bytes (as write support is most often
not needed in SPL).
This is important on this platform, where the maximum
SPL size is 14 KiB.
With gcc v7.3, this change saves 144 bytes producing:
size spl/u-boot-spl
text data bss dec hex filename
9240 752 712 10704 29d0 spl/u-boot-spl
To make the code easier to compile-out and more
readable, a pair of read_data/write_data helpers are created.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Use CONFIG_IS_ENABLED(BLK) instead of CONFIG_BLK,
in order to fix the following build issues when
CONFIG_SPL_MMC_WRITE is selected:
drivers/mmc/mmc_write.c:69:7: error: conflicting types for 'mmc_berase'
ulong mmc_berase(struct udevice *dev, lbaint_t start, lbaint_t blkcnt)
^~~~~~~~~~
In file included from drivers/mmc/mmc_write.c:15:0:
drivers/mmc/mmc_private.h:39:7: note: previous declaration of 'mmc_berase' was here
ulong mmc_berase(struct blk_desc *block_dev, lbaint_t start, lbaint_t blkcnt);
^~~~~~~~~~
drivers/mmc/mmc_write.c:187:7: error: conflicting types for 'mmc_bwrite'
ulong mmc_bwrite(struct udevice *dev, lbaint_t start, lbaint_t blkcnt,
^~~~~~~~~~
In file included from drivers/mmc/mmc_write.c:15:0:
drivers/mmc/mmc_private.h:37:7: note: previous declaration of 'mmc_bwrite' was here
ulong mmc_bwrite(struct blk_desc *block_dev, lbaint_t start, lbaint_t blkcnt,
^~~~~~~~~~
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
There is no real difference between the generic variant and
the custom variant except that the generic variant is more
optimised. This also saves 24 Bytes in the SPL binary.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
Discard ABI related sections which are not required for debugging.
Rearrange debug sections similar to Linux. Remove the remaining
explicitely specified sections in the unused part because those
sections are not created anymore or because the linker puts them
by default at the end of the ELF binary.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'ocelot' pcb123 and pcb120.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
This enables the use of the MSCC serial GPIO driver on the MSCC
VCoreIII 'ocelot' SOC, and add gpio-leds nodes to the pcb123 and
pcb120 DT.
Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com>
This enables the use of the MSCC serial GPIO driver to control the
LEDs on the MSCC VCoreIII 'luton' SoC.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
This enables the use of the MSCC serial GPIO driver, and add gpio-leds
nodes to the 'luton' pcb090 and pcb091 DT.
Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com>
This add device tree binding documentation for the MSCC serial GPIO
driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microsemi.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This add support for the the MSCC serial GPIO driver in MSCC
VCoreIII-based SOCs.
By using a serial interface, the SIO controller significantly extends
the number of available GPIOs with a minimum number of additional pins
on the device. The primary purpose of the SIO controller is to connect
control signals from SFP modules and to act as an LED controller.
This adds the base driver.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
As we are moving to multi-dtb and board detection, remove static board
config options, and introduce board probing instead.
Luton: This add single-binary support for the two MSCC luton-based
reference boards - pcb090 and pcb091. The SoC chip ID is used to
determine the board type.
Ocelot: This add single-binary support for the two MSCC ocelot-based
reference boards - pcb120 and pcb123. The PHY ids on specific ports
are used to determine the board type.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
This prepares individual device trees for MSCC luton-based reference
boards - pcb090 and pcb091.
Note: Even though the devices trees are quite common, they will differ
significantly in coming patches.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
The GPIO control function can be used for controlling alternate
functions associated with a GPIO.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
The following hang is observed on a Hummingboard 2 MicroSOM
i2eX iMX6D - rev 1.3 with no eMMC populated on board:
U-Boot SPL 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)
Trying to boot from MMC1
U-Boot 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)
CPU: Freescale i.MX6D rev1.5 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 33C
Reset cause: POR
Board: MX6 HummingBoard2
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
---> hangs
which is caused by the following infinite loop inside esdhc_send_cmd_common()
while (!(esdhc_read32(®s->irqstat) & flags))
;
Instead of looping forever, provide an exit path so that a timeout
error can be propagated in the case irqstat does not report
any interrupts, which may happen when no eMMC is populated on
board.
Reported-by: Ricardo Salveti <rsalveti@rsalveti.net>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Ricardo Salveti <rsalveti@rsalveti.net>
Chris Spencer reports that when enabling ext4 read support without
also enabling write support the following error is seen:
fs/fs.c:198:12: error: 'ext4_write_file' undeclared here (not in a
function); did you mean 'ext4_read_file'?
.write = ext4_write_file,
^~~~~~~~~~~~~~~
Fix this problem by moving these options to Kconfig.
Reported-by: Chris Spencer <spencercw@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Change CONFIG_ENV_OFFSET for Poplar to be 1MB further into the eMMC
than before. This puts it immediately prior to the space we are
reserving offset 0x200000-0x400000 for UEFI to save its persistent
data. Define CONFIG_ENV_SIZE as a product of env_mmc_nblks and the
sector size, like CONFIG_ENV_OFFSET is.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This particular commit is causing a regression on stih410-b2260 and
other platforms when reading from FAT16. Noting that I had rebased the
original fix from Thomas onto then-current master, there is also
question from Akashi-san if the change is still needed after other FAT
fixes that have gone in.
This reverts commit a68b0e11ea.
Reported-by: Patrice Chotard <patrice.chotard@st.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit a7f4b4b344.
As reported by Alex Kiernan the above optimization introduces a
regression in the below use case where:
1. Device has defined 'u-boot,dm-spl' property (@ eMMC DTS node)
2. The device downloads its MLO/SPL via UART (not eMMC - the eMMC pinmux
pins are NOT probed/configured in MLO/SPL).
3. The loaded via UART MLO/SPL wants to load Linux from eMMC. In this case
the DM core and pinctrl uclass checks 'u-boot,dm-spl' and don't
configure pins (as it thinks that those were initialized in MLO/SPL).
As we are very close to release - please revert this commit.
Reported-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SDMMC reset is missing from DT, so the reset manager cannot unreset
the SDMMC. Add the missing DT reset entry.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Fixes commit 0131162439 ("dm: usb: create a new UCLASS ID for USB gadget
devices")
The UCLASS_DRIVER for id UCLASS_USB_GADGET_GENERIC needs to be declared
even for platforms that do not enable DM_USB_GADGET. Otherwise the driver
for their usb peripheral controller fails to bind.
Reported-by: Priit Laes <plaes@plaes.org>
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Priit Laes <plaes@plaes.org>
Acked-by: Jagan Teki <jagan@openedev.com>
There is no need to compile and include this code if it is not used.
CONFIG_USB_GADGET can be used for the purpose.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
dfu, fastbot and other usb gadget commands take the USB port index as a
parameter. Currently this index is assigned in the order of the driver
bindings.
Changing this behavior using the SEQ_ALIAS feature. This option assign to
the device a SEQ number based on its alias (if it exists)
To use it we must set the DM_UC_FLAG_SEQ_ALIAS flag and follow the existing
naming convention: use "usb" for the name of the gadget UCLASS_DRIVER
(same as for the UCLASS_USB).
If no alias is provided, then the index falls back to the order in which
the bindings took place.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Existing clock configure code has been followed based on the
legacy MMC dt node definitions and it cannot work with recent
dts(i) sync from Linux.
So, add clock configure code for Allwinner platforms which support
DM_MMC and eventually this will drop once CLK support is in Mainline.
Fixes: 3c92cca3cd ("ARM: dts: sun4i: Update A10 dts(i) files from Linux-v4.18-rc3")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Priit Laes <plaes@plaes.org> # Gemei G9 A10 Tablet
Tested-by: Marek Kraus <gamelasterv2@gmail.com> # A10-OLinuXino-Lime
OSC_27M_CLK should return 27MHz and OSC_32K_CLK should return
32768Hz to reflect the reality.
This also keeps the values in sync with the Linux clock tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
To B0[+] chips, dcd_skip needs to be true. For A0 chip, it needs
to be false, however A0 chip is no longer being supported anymore.
Considering we are moving code from imx-mkimage to uboot mkimage,
to make sure we not introduce some surprise, we still keep dcd_skip
code there.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The CPU banner printed is as following:
CPU: CPU: Freescale i.MX8QXP RevB A35 at 147228 MHz
1. Drop the CPU:
2. Change vendor from Freescale to NXP
Signed-off-by: Peng Fan <peng.fan@nxp.com>
priv data has not been allocated when doing bind, so it is
wrong to use dev_get_priv in bind call back.
Let's switch to use platdata in the driver to fix the issue.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When boot_dev is true, fill boot device. However the original logic is when
boot_dev is false, fill boot device, this will trigger data abort.
Also fix sc_misc_get_control when using pointer val.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When build clk driver in spl, met the warning:
"
drivers/clk/imx/clk-imx8.c:21:25: warning: ‘imx8_clk_names’ defined but not used [-Wunused-variable]
static struct imx8_clks imx8_clk_names[] = {
^~~~~~~~~~~~~~
"
Fix with wrapping the array with CONFIG_CMD_CLK.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current defconfig build generates a u-boot.imx file that is too large
for the available space on a eMMC/SD card. Installing this file overwrites
the u-boot environment. So disable the unused FIT support to reduce the
size of the u-boot binary.
Signed-off-by: Soeren Moch <smoch@web.de>
Check the size of the generated u-boot.imx file. Report an error
if it would be too big and overwrite the u-boot environment.
Signed-off-by: Soeren Moch <smoch@web.de>
The mkimage_fit_atf.sh SPL FIT generator script requires
u-boot-nodtb.bin, but this was not enforced by the Makefile. This could
cause the generator script to be executed before u-boot-nodtb.bin has
been created.
Signed-off-by: Chris Spencer <christopher.spencer@sea.co.uk>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
The current value CTLUPD_AREF(0) is the reset value of the register,
so there is no need to write a value. If needed, the register can be
written using board specific CR settings.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The CR80 register has multiple interrupt bits, the code is supposed
to check bit 8 but instead uses a logical and. In most cases this
probably did not affect real operations since at that stage typically
none of the other bits are set.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>