Commit graph

21 commits

Author SHA1 Message Date
Kumar Gala
04a641df25 powerpc/8xxx: Fix possible compile issue related to P1013
The P1013 is a single core version of P1022 and thus should use the
p1022_serdes.c code.  It was acciently pointing to p1013_serdes.c which
doesn't exist.

Reported-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-04 14:04:21 -06:00
Kumar Gala
1eda59ff6b powerpc/p5020: Add various p5020 specific information
Add P5020 SoC specific information:
* SERDES Table
* LIODN setup
* Portal configuration

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Kumar Gala
d5d2cd4331 powerpc/p3041: Add various p3041 specific information
Add P3041 SoC specific information:
* SERDES Table
* LIODN setup
* Portal configuration

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Poonam Aggrwal
b5debec5b5 powerpc/85xx: Add Support for Freescale P1014 Processor
The P1014 is similar to the P1010 processor with the following differences:

- 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
- no eCAN interface. (P1010 has 2 eCAN interfaces)
- Two SGMII interface (P1010 has 3 SGMII)
- No secure boot

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Poonam Aggrwal
b8cdd01462 powerpc/85xx: Add Support for Freescale P1010 Processor
Key Features include of the P1010:
* e500v2 core frequency operation of 500 to 800 MHz
* Power consumption less than 5.0 W at 800 MHz core speed
* Dual SATA 3 Gbps controllers with integrated PHY
* Dual PCI Express controllers
* Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
	* TCP/IP acceleration and classification capabilities
	* IEEE 1588 support
	* Lossless flow control
	* RGMII, SGMII
* DDR3 with support for a 32-bit data interface (40 bits including ECC),
  up to 800 MHz data rate 32/16-bit DDR3 memory controller
* Dedicated security engine featuring trusted boot
* TDM interface
* Dual controller area networks (FlexCAN) controller
* SD/MMC card controller supporting booting from Flash cards
* USB 2.0 host and device controller with an on-chip, high-speed PHY
* Integrated Flash controller (IFC)
* Power Management Controller (PMC)
* Four-channel, general-purpose DMA controller
* I2C controller
* Serial peripheral interface (SPI) controller with master and slave support
* System timers including a periodic interrupt timer, real-time clock,
  software watchdog timer, and four general-purpose timers
* Dual DUARTs

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:23 -06:00
Kumar Gala
70ea7f82ed powerpc/85xx: Add is_serdes_configured() support for P1021 SERDES
Add the ability to determine if a given IP block connected on SERDES is
configured.  This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:18 -06:00
Kumar Gala
877a26112d powerpc/85xx: Add is_serdes_configured() support for MPC8544 SERDES
Add the ability to determine if a given IP block connected on SERDES is
configured.  This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:18 -06:00
Kumar Gala
47567c2663 powerpc/85xx: Add is_serdes_configured() support for MPC8569 SERDES
Add the ability to determine if a given IP block connected on SERDES is
configured.  This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:18 -06:00
Kumar Gala
5ba40eec72 powerpc/85xx: Add is_serdes_configured() support for MPC8568 SERDES
Add the ability to determine if a given IP block connected on SERDES is
configured.  This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:18 -06:00
Kumar Gala
bc48d0d503 powerpc/85xx: Add is_serdes_configured() support for MPC8548 SERDES
Add the ability to determine if a given IP block connected on SERDES is
configured.  This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:18 -06:00
Kumar Gala
af87cab677 powerpc/85xx: Add is_serdes_configured() support for MPC8572 SERDES
Add the ability to determine if a given IP block connected on SERDES is
configured.  This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.

Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:18 -06:00
Kumar Gala
3818db43de powerpc/85xx: Add is_serdes_configured() support for P2020 SERDES
Add the ability to determine if a given IP block connected on SERDES is
configured.  This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.

Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:18 -06:00
Kumar Gala
c5780a6fe9 powerpc/85xx: Create a SERDES section in Makefile
Created a section in the Makefile for SoC specific SERDES code.  Also
added P1013 SERDES (use P1022 SERDES code).

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:18 -06:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Kumar Gala
34a8258fea powerpc/p4080: Add support for initializing SERDES
Add support for initializing the SERDES blocks on CoreNet style QoriQ
devices and the p4080 specific SERDES tables to know which actual
componetns are enabled.

Additionally, split out the Frame Manger (FMAN) into its specific ethernet
ports instead of gross level of the full FMAN.

Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26 13:07:57 -05:00
Kumar Gala
db977abfc8 powerpc/85xx: Add support to initialize LIODN registers and portals
On the new QorIQ/CoreNet based platforms we need to initialize the
"portals" as access into the Data Path subystem as well as Logical IO
Device Numbers (LIODN) that are used for the IOMMU (PAMU).

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26 13:07:56 -05:00
Kumar Gala
c26de2d8b1 powerpc/p3041: Add various p3041 related defines
There are various locations that we have chip specific info:

* Makefile for which ddr code to build
* Added p3041 to cpu_type_list and SVR list
* Added number of LAWs for p3041
* Set CONFIG_MAX_CPUS to 4 for p3041

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-20 04:41:19 -05:00
Kumar Gala
19dbcc96c0 powerpc/p5020: Add various p5020 related defines (and p5010)
There are various locations that we have chip specific info:

* Makefile for which ddr code to build
* Added p5020 & p5010 to cpu_type_list and SVR list
* Added number of LAWs for p5020
* Set CONFIG_MAX_CPUS to 2 for p5020

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-20 04:41:19 -05:00
Kumar Gala
79ee344802 powerpc/85xx: Add command to report errata workarounds
Add 'errata' command to report what errata we workaround.  Report
workaround for erratum SATA-A001 on P1022/P1013.

Also sorted the CONFIG_CMD_* list.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:10 -05:00
Timur Tabi
c59e1b4d07 powerpc: add support for the Freescale P1022DS reference board
Specifics:

1) 36-bit only
2) Booting from NOR flash only
3) Environment stored in NOR flash only
4) No SPI support
5) No DIU support

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:10 -05:00
Stefan Roese
a47a12becf Move arch/ppc to arch/powerpc
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.

Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
2010-04-21 23:42:38 +02:00
Renamed from arch/ppc/cpu/mpc85xx/Makefile (Browse further)