Long are gone the times TF-A couldn't handle the FDT passed by U-Boot.
Specifically, since commit e7b586987c0a ("rockchip: don't crash if we
get an FDT we can't parse") in TF-A, failure to parse the FDT will use
the fallback mechanism. This patch was merged in TF-A v2.4-rc0 from two
years ago.
New boards should likely have this option disabled or explicitly enable
it in their respective defconfig.
Because existing boards might depend on a TF-A version that predates
v2.4, let's just enable this option in all RK3399 defconfigs.
Maintainers of each board can decide for themselves if they would prefer
to disable this option and allow U-Boot to pass the DT to TF-A.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.
Add support for this SoM and IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.
General features:
- Rockchip RK3588J
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
- On module WiFi6/BT
Neural Compute Module 6B(Neu6B) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
General features:
- microSD slot
- 1x HDMI Out
- 1x HDMI In
- 2x DP
- 1x eDP
- 2x MIPI DSI connector
- 4x MIPI CSI2 connector
- 2x USB Host
- 2x USB 3.0 OTG/Host
- 1x SATA
- 1x 2.5Gbps Ethernet
- 1x M.2 B-Key for 4G/5G cards
- 1x M.2 M-Key slot
- 1x Onboard PoE
- 1x RS485, RS232, CAN
- 1x Audio, MIC port
- RTC battery slot
- 40-pin GPIO expansion
Neu6B needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6B(Neu6B) IO platform.
Kernel commits:
commit <5f06c3f508f7> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B SoM")
commit <3a9181a43b94> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B IO")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add rk3588j-u-boot.dtsi for adding U-Boot specific nodes and
properties for Rockchip RK3588J SoC.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip RK3588J is the industrial-grade version of RK3588 SoC and
is operated with -40 °C to +85 °C temparature.
Add rk3588j specific dtsi for adding rk3588j specific operating points
and other changes to be add in future.
Kernel commit:
commit <8274a04ff1dc> ("arm64: dts: rockchip: Add Rockchip RK3588J")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
FriendlyARM NanoPi R5C is an open-sourced mini IoT gateway device.
Specification:
- Rockchip RK3568
- 1/4GB LPDDR4X RAM
- 8/32GB eMMC
- SD card slot
- M.2 Connector
- 2x USB 3.0 Port
- 2x 2500 Base-T (PCIe, r8125)
- HDMI 2.0
- MIPI DSI/CSI
- USB Type C 5V
The device tree is taken from kernel v6.4-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
FriendlyARM NanoPi R5S is an open-sourced mini IoT gateway device.
Board Specifications
- Rockchip RK3568
- 2 or 4GB LPDDR4X
- 8GB or 16GB eMMC, SD card slot
- GbE LAN (Native)
- 2x 2.5G LAN (PCIe)
- M.2 Connector
- HDMI 2.0, MIPI DSI/CSI
- 2xUSB 3.0 Host
- USB Type C PD, 5V/9V/12V
- GPIO: 12-pin 0.5mm FPC connector
The device tree is taken from kernel v6.4-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and RAM type
changed from DDR4 to LPDDR3.
The device tree is taken from kernel v6.4-rc1.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
The device tree and description are taken from kernel v6.3-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Update the Anbernic RGxx3 documentation to note that panel detection
has been added and how it works.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update the anbernic-rgxx3_defconfig file to support panel autodetection
and automatically updating the compatible string in the devicetree.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support to automatically detect the panel for the Anbernic RGxx3.
This is done by creating a "pseudo driver" that provides only the bare
minimum to start the DSI controller and DSI DPHY. Once started, we then
can query the panel for its panel ID and compare it to a table of known
values. The panel compatible string (which corresponds to the upstream
Linux driver) is then defined as an environment variable "panel". The
panel compatible string is also changed automatically via an
ft_board_setup() call if what is detected differs from what is in the
loaded tree. This way, end users can use the same bootloader without
having to worry about which panel they have (as there is no obvious
way of knowing).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the RG353PS to the Anbernic RGxx3. This device is a
slightly pared down version of the RG353P with no eMMC, no touchscreen,
and only 1GB of RAM.
Refactor board logic so that all supported devices are defined with
ADC values and that future boards can be added by just defining the
board values in the device array.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the DSI and DSI-DPHY to U-Boot for the RGxx3. These are
needed so we can send a panel ID request to determine which panel is
being used.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The pinctrl on the Anbernic RGxx3 for the i2c2 bus does not use the
default value, so explicitly define it.
Fixes: 6cf6fe2537 ("board: rockchip: add Anbernic RGXX3 Series Devices")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable configuration for USB 3.0 controller, the commands required,
and the gadget drivers.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the USB3.0 host node, and gadget node.
The gadget is available through the USB type C connector on the board.
The connector is tied to a Fairchild fusb302b device, which currently
does not have a driver in U-boot, but the node is here for correct
description of the board + Linux future compatibility.
It will be easier to move the node as-is when it will be available
in the DT from Linux
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the USB 3.0 devices in rk3588:
- USB DRD(dual role device) 3.0 #0 as usbdrd3_0 which is available in
rk3588s
- USB DRD(dual role device) 3.0 #1 as usbdrd3_1 which is available in
rk3588 only
- USB DP PHY (combo USB3.0 and DisplayPort Alt Mode ) #0 phy interface
as usbdp_phy0
- USB DP PHY (combo USB3.0 and DisplayPort Alt Mode ) #1 phy interface
as usbdp_phy1
- USB 2.0 phy #2 , the USB 3.0 device can work with this phy in USB 2.0
mode
- associated GRFs (general register files) for the devices.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[eugen.hristev@collabora.com: move nodes to right place, adapt from latest
linux kernel]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds a new USBDP combo PHY with Samsung IP block driver.
The PHY is a combo between USB 3.0 and DisplayPort alt mode.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
[eugen.hristev@collabora.com: ported to 2023.07, clean-up]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the devicetree with linux-next tag: next-20230525
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This just needs some extra clocks enabled, and different registers
configured. Copied from Linux, just like the original submitter
of this driver did for rk3568.
Tested on Pinephone Pro.
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@vrull.eu>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update the board.c file for the Odroid Go Advance to support the
Black Edition and the Odroid Go Super. The Odroid Go Advance Black
Edition differs from the original model with the addition of 2
extra buttons and an ESP8266 WiFi module. The Odroid Go Super
adds an additional 2 buttons compared to the Black Edition, along
with a larger panel and larger battery.
This change uses the value of ADC0 to determine which of these
3 models it is, and then changes the ${fdtfile} environment variable
to match the proper devicetree name in mainline Linux.
Tested on an Odroid Go Advance (first revision) and an Odroid Go Super.
The correct ${fdtfile} variable was set for each device.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the rtl8169 driver, which supports the rtl8125b device, which is
connected on the pciE bus on this board.
Enable also CONFIG_SYS_HAS_NONCACHED_MEMORY to have the descriptors stored.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Introduce common variables to define a generic build instruction that is
then used in specific board specific description.
Labels are introduced in the evm.rst files to be then reused in variant
board documentation as well.
While at this, drop using ARCH=arm when building u-boot sources. This
practice has been discouraged for some time and can potentially create
problems with Kconfig rules related to aarch64. It's best to avoid
this approach.
Signed-off-by: Nishanth Menon <nm@ti.com>
Update the bootflow svg diagram instead of the ascii version
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Update the bootflow svg diagram instead of the ascii version
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Update the bootflow svg diagram and reuse across the platforms as they
are common.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
We have duplication of sources which makes it hard to sustain across the
board, but at the same time, we'd like to ensure readers get specific
information without having to cross refer to different documentation to
get piecemeal information that they need to put together.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Now that we are using binman in all cases on these platforms, reword
things to be clearer that for filesystem booting we need to use a
specific name for each component.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
The EFI doesn't allow removal of handles, unless all hosted protocols
are cleanly removed. Our efi_delete_handle() is a bit intrusive.
Although it does try to delete protocols before removing a handle,
it doesn't care if that fails. Instead it only returns an error if the
handle is invalid. On top of that none of the callers of that function
check the return code.
So let's rewrite this in a way that fits the EFI spec better. Instead
of forcing the handle removal, gracefully uninstall all the handle
protocols. According to the EFI spec when the last protocol is removed
the handle will be deleted. Also switch all the callers and check the
return code. Some callers can't do anything useful apart from reporting
an error. The disk related functions on the other hand, can prevent a
medium that is being used by EFI from removal.
The only function that doesn't check the result is efi_delete_image().
But that function needs a bigger rework anyway, so we can clean it up in
the future
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* Add a new page about the emulation of block devices
* Add semihosting to the emulation index page
* Set toc maxdepth to 1 to improve readability
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
%s/device_compat\/.h/device_compat.h/
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the recursive dp_fill(dev->parent) call to a single location.
Determine uclass_id only once.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The UEFI specification does not provide node types matching UCLASS_BLKMAP,
UCLASS_HOST, UCLASS_VIRTIO block devices.
The current implementation uses VenHw() nodes with uclass specific GUIDs
and a single byte for the device number appended. This leads to unaligned
integers in succeeding device path nodes.
The current implementation fails to create unique device paths for block
devices based on other uclasses like UCLASS_PVBLOCK.
Let's use a VenHw() node with the U-Boot GUID with a length dividable by
four and encoding blkdesc->uclass_id as well as blkdesc->devnum.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
