Commit graph

103 commits

Author SHA1 Message Date
Simon Glass
76b00aca4f board_f: Drop setup_dram_config() wrapper
By making dram_init_banksize() return an error code we can drop the
wrapper. Adjust this and clean up all implementations.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2017-04-05 16:36:51 -04:00
Liviu Dudau
88e0d59315 vexpress64: Juno: Change PCI buss addresses for IO to start from zero.
Juno uses a 1:1 mapping between CPU and PCI addresses for IO. First,
that will trip devices that cannot use more than 16 bits of addresses
for IO, second it is un-necessary as the system can handle zero-based
PCI addresses just fine.

Change the mapping to start IO bus addresses from zero.

Signed-off-by: Liviu Dudau <Liviu.Dudau@foss.arm.com>
2016-11-29 08:15:30 -05:00
Sudeep Holla
03ab5d136b vexpress: disable cci ace slave ports when booting in non-sec/hyp mode
Commit f225d39d30 ("vexpress: Check TC2 firmware support before defaulting
to nonsec booting") added support to check if the firmware on TC2  is
configured appropriately before booting in nonsec/hyp mode.

However when booting in non-secure/hyp mode, CCI control must be done in
secure firmware and can't  be done in non-secure/hyp mode. In order to
ensure that, this patch disables the cci slave port inteface so that it
is not accessed at all.

Cc: Jon Medhurst <tixy@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jon Medhurst <tixy@linaro.org>
2016-10-07 14:26:30 +00:00
Jon Medhurst \(Tixy\)
f225d39d30 vexpress: Check TC2 firmware support before defaulting to nonsec booting
The firmware on TC2 needs to be configured appropriately before booting
in nonsec mode will work as expected, so test for this and fall back to
sec mode if required.

Signed-off-by: Jon Medhurst <tixy@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
2016-08-15 18:46:38 -04:00
York Sun
cd4b0c5fea armv8: mmu: Add support of non-identical mapping
Introduce virtual and physical addresses in the mapping table. This change
have no impact on existing boards because they all use idential mapping.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-07-15 09:01:43 -07:00
Alexander Graf
e593bf5eb3 vexpress64: Add MMU tables
There's no good excuse for running with caches disabled on AArch64,
so let's just move the vexpress64 target to enable the MMU and run
with caches on.

Signed-off-by: Alexander Graf <agraf@suse.de>
2016-03-15 15:13:04 -04:00
Ryan Harkin
2c2b218383 vexpress64: use 2nd DRAM bank only on juno
This patch makes the 2nd DRAM bank available on Juno only and not on
other vexpress64 targets, eg. the FVP models.

The commit below added a 2nd bank of NOR flash for Juno, but also for
all vexpress64 targets:

    commit 2d0cee1ca2
    Author: Liviu Dudau <Liviu.Dudau@foss.arm.com>
    Date:   Mon Oct 19 11:08:31 2015 +0100

    vexpress64: Juno: Declare all 8GB of RAM and make them visible to the kernel.

    Juno comes with 8GB RAM, but U-Boot only passes 2GB to the kernel.
    Declare a secondary memory bank and set the sizes correctly.

    Signed-off-by: Liviu Dudau <Liviu.Dudau@foss.arm.com>
    Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
    Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
    Tested-by: Ryan Harkin <ryan.harkin@linaro.org>

Unfortunately, I only fully tested on Juno R0, R1 and the FVP Foundation
model.  Whilst FVP Base AEMV8 models run U-Boot OK, they fail to boot
the kernel.

Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-21 21:50:28 -05:00
Ryan Harkin
bc8d3bc023 vexpress64: compile Juno PCIe conditionally
Only compile in PCIe support if the board really uses it. Provide
a __weak stub for the init function if e.g. FVP is being built.

Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
2015-11-21 21:50:27 -05:00
Andre Przywara
0ee1a22b6d Juno: don't print PCI debug information by default
On a Juno r1 the PCI controller init routine outputs the rather boring
ATR entry information.
Do this only with DEBUG defined to avoid cluttering the user's
terminal.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Ryan Harkin <ryan.harkin@linaro.org>
2015-11-21 21:50:27 -05:00
Liviu Dudau
2fdc9b741b vexpress64: Juno: Add initialisation code for Juno R1 PCIe host bridge.
Juno R1 has an XpressRICH3 PCIe host bridge that needs to be initialised
in order for the Linux kernel to be able to enumerate the bus. Add
support code here that enables the host bridge, trains the links and
sets up the Address Translation Tables.

Signed-off-by: Liviu Dudau <Liviu.Dudau@foss.arm.com>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
[trini: Always declare vexpress64_pcie_init and continue handling logic
inside the function]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-10-19 17:05:46 -04:00
Liviu Dudau
2d0cee1ca2 vexpress64: Juno: Declare all 8GB of RAM and make them visible to the kernel.
Juno comes with 8GB RAM, but U-Boot only passes 2GB to the kernel.
Declare a secondary memory bank and set the sizes correctly.

Signed-off-by: Liviu Dudau <Liviu.Dudau@foss.arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
2015-10-19 17:05:28 -04:00
Ryan Harkin
fc04b92354 vexpress64: fvp dram: add DRAM configuration
Create an additional FVP configuration to boot images pre-loaded into
DRAM.

Sometimes it's preferential to boot the model by loading the files
directly into DRAM via model parameters, rather than using
SemiHosting.

An example of model parmaters that are used to pre-load the files
into DRAM:
    --data cluster0.cpu0=Image@0x80080000 \
    --data cluster0.cpu0=fvp-base-gicv2-psci.dtb@0x83000000 \
    --data cluster0.cpu0=uInitrd@0x84000000

Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[trini: Update board/armltd/vexpress64/Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-10-11 17:11:47 -04:00
Ryan Harkin
b483cb5a94 vexpress64: Kconfig: tidy up
The FVP and Juno settings were identical, but duplicated, so I removed
the duplication with this patch.

Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[trini: Adjust logic to keep if/endif in the file]
Signed-off-by: Tom Rini <trini@konsulko.com>
2015-10-11 09:17:03 -04:00
Simon Glass
b928e658f4 arm: Remove versatileab board
This board has not been converted to generic board by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-09-11 15:01:25 -04:00
Linus Walleij
3f394e70f0 integrator: switch to DM serial port
This switches the Integrator boards over to using the device model
for its serial ports.

Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-08-12 20:47:49 -04:00
Jan Kiszka
104d6fb6cd ARM: Clean up CONFIG_ARMV7_NONSEC/VIRT/PSCI conditions
CONFIG_ARMV7_VIRT depends on CONFIG_ARMV7_NONSEC, thus doesn't need to
be taken into account additionally. CONFIG_ARMV7_PSCI is only set on
boards that support CONFIG_ARMV7_NONSEC, and it only works on those.

CC: Tang Yuantian <Yuantian.Tang@freescale.com>
CC: York Sun <yorksun@freescale.com>
CC: Steve Rae <srae@broadcom.com>
CC: Andre Przywara <andre.przywara@linaro.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:13 -07:00
Linus Walleij
ab93bf063b integrator: stop zeroing the gd flags
This assignment conflicts with code that add flags with
gd->flags |= FOO prior to the execution of this function.
Seems like a historical artifact and creates bugs with
early alloc().

Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-23 08:52:27 -04:00
Masahiro Yamada
5cbbd9bd0a ARM: integrator: move board select into mach-integrator/Kconfig
The board/SoC select menu in arch/arm/Kconfig is still cluttered.
Add ARCH_INTEGRATOR into arch/arm/Kconfig and move the board select
under arch/arm/mach-integrator.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
2015-04-23 08:52:27 -04:00
Linus Walleij
d280ea00ef vexpress64: use DM for all vexpress64 boards
Commit d8bafe1310
"ARMv8: enable DM in vexpress64 board" only enabled DM
for the simulated vexpress64 board (FVP) with the
hardcoded clock value for the simulated board, causing
a console regression on the Juno board which was using
a different clock setting.

Fix this by enabling DM for all vexpress64 boards,
defining the clock frequency per-board, deleting the
static array of PL01x ports from the config file and
relying solely on the port defined in the boardfile
using platform data.

Cc: David Feng <fenghua@phytium.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-23 08:52:26 -04:00
Tom Rini
692e5c4e7e Merge branch 'master' of git://git.denx.de/u-boot-tegra
Conflicts:
	board/armltd/vexpress64/vexpress64.c

Signed-off-by: Tom Rini <trini@konsulko.com>
2015-04-03 09:14:38 -04:00
Linus Walleij
03314f0e24 vexpress64: cut config and defaults for unclear variant
This variant that is neither FVP / Base Model or Juno Versatile
Express 64bit is confusing. Get rid of it unless someone can
point out what machine that really is. Seems to be an evolutional
artifact in the config base.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-28 12:07:46 -04:00
Linus Walleij
49995ffe81 vexpress64: remove board late init, use smhload
This removes the kludgy late board init from the FVP simulator
version of Versatile Express 64bit (ARMv8), and replace it with
a default boot command using the new smhload command to load
the files using semihosting. Tested on the Foundation Model.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-28 12:07:45 -04:00
David Feng
d8bafe1310 ARMv8: enable DM in vexpress64 board
Signed-off-by: David Feng <fenghua@phytium.com.cn>
2015-03-27 16:33:51 +01:00
Rob Herring
7682a99826 remove unnecessary version.h includes
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: "David Müller" <d.mueller@elsoft.ch>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Torsten Koschorrek <koschorrek@synertronixx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Łukasz Majewski <l.majewski@samsung.com>
2015-03-24 10:50:50 -04:00
Linus Walleij
23b5877c64 armv8/vexpress64: make multientry conditional
While the Freescale ARMv8 board LS2085A will enter U-Boot both
on a master and a secondary (slave) CPU, this is not the common
behaviour on ARMv8 platforms. The norm is that U-Boot is entered
from the master CPU only, while the other CPUs are kept in
WFI (wait for interrupt) state.

The code determining which CPU we are running on is using the
MPIDR register, but the definition of that register varies with
platform to some extent, and handling multi-cluster platforms
(such as the Juno) will become cumbersome. It is better to only
enable the multiple entry code on machines that actually need
it and disable it by default.

Make the single entry default and add a special
ARMV8_MULTIENTRY KConfig option to be used by the
platforms that need multientry and set it for the LS2085A.
Delete all use of the CPU_RELEASE_ADDR from the Vexpress64
boards as it is just totally unused and misleading, and
make it conditional in the generic start.S code.

This makes the Juno platform start U-Boot properly.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-09 11:13:29 -04:00
Linus Walleij
b31f9d7a4a vexpress64: juno: support SMC9118 ethernet
This configures the Juno board to enable ethernet using the
SMSC9118 ethernet controller found in the board. Tested by
TFTP-booting a kernel over ethernet.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-05 20:49:42 -05:00
Linus Walleij
ffc103732c vexpress64: support the Juno Development Platform
The Juno Development Platform is a physical Versatile Express
device with some differences from the emulated semihosting
models. The main difference is that the system is split in
a SoC and an FPGA where the SoC hosts the serial ports at
totally different adresses.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-01-30 09:19:17 -05:00
Linus Walleij
f91afc4d00 vexpress64: get rid of CONFIG_SYS_EXTRA_OPTIONS
The Versatile Express ARMv8 semihosted FVP platform is still
using the legacy CONFIG_SYS_EXTRA_OPTIONS method to configure
some compile-time flags. Get rid of this and create a Kconfig
entry for the FVP model, and a selectable bool for the
semihosting library.

The FVP subboard is now modeled as a target choice so we can
eventually choose between different ARMv8 versatile express
boards (FVP, base model, Juno...) this way. All dependent
symbols are updated to reflect this.

The 64bit Versatile Express board symbols are renamed
VEXPRESS64 so we have some chance to see what is actually
going on. Tested on the FVP fast model.

Acked-by: Steve Rae <srae@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-01-30 09:19:17 -05:00
Linus Walleij
058235c06b vexpress64: take over maintenance of the semi vexpress64
As agreed with Steve Rae I'm taking over maintenance of the
semihosted, emulated FVP/foundation model Versatile Express
64 bit board variant.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Steve Rae <srae@broadcom.com>
2014-12-29 07:44:06 -05:00
Georges Savoundararadj
2e07c249a6 kconfig: arm: introduce symbol for ARM CPUs
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.

For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.

Also, it removes redundant "string" type in some Kconfig files.

Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-29 09:02:09 -04:00
Masahiro Yamada
535aad29f2 MAINTAINERS: comment out blank M: field
Since commit ddaf5c8f30
(patman: RunPipe() should not pipe stdout/stderr unless asked),
Patman spits lots of "Invalid MAINTAINERS address: '-'"
error messages for patches with global changes.
It takes too long for Patman to process them.

Anyway, "M:    -" does not carry any important information.
Rather, it is just like a place holder in case of assigning
a new board maintainer.  Let's comment out.

This commit can be reproduced by the following command:

find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/'

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-24 18:30:28 -04:00
Masahiro Yamada
e5a504eb3d MAINTAINERS: comment out invalid maintainers
The "S:    Orphan" in MAINTAINERS means that the maintainer in the
"M:" field is unreachable (i.e. the email address is not working).
(Refer to the definition of "Orphan" adopted in U-Boot
in the log of commit 31f1b654b2,
"boards.cfg: move boards with invalid emails to Orphan")

For patch files adding global changes, scripts/get_maintainer.pl
adds bunch of such invalid email addresses, which results in
tons of annoying bounce emails.

This commit can be reproduced by the following command:

find . -name MAINTAINERS | xargs sed -i -e '
/^M:[[:blank:]]/ {
      N
      /S:[[:blank:]]Orphan/s/^/#/
}
'

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-09-24 18:30:28 -04:00
Masahiro Yamada
016a954ee9 kconfig: armv8: move CONFIG_ARM64 to Kconfig
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-16 12:24:00 -04:00
Masahiro Yamada
8813fdaf4b vexpress64: kconfig: consolidate CONFIG_TARGET_VEXPRESS_AEMV8A_SEMI
We do not have to distinguish CONFIG_TARGET_VEXPRESS_AEMV8A_SEMI
from CONFIG_TARGET_VEXPRESS_AEMV8A.  Rename the former to the latter.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Cc: David Feng <fenghua@phytium.com.cn>
2014-09-16 12:24:00 -04:00
Masahiro Yamada
461be2f96e kconfig: remove redundant "string" type in arch and board Kconfigs
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.

We can delete the ones in arch and board Kconfig files.

This commit can be easily reproduced by the following command:

find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
    N
    s/\n[[:space:]]*string//
}
'

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-13 16:43:55 -04:00
Masahiro Yamada
ad17a81c06 versatile: kconfig: move common settings
Move Versatile-specific settings to versatile/Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-30 21:19:32 -04:00
Masahiro Yamada
aee63751d9 MAINTAINERS: change the status of vexpress board to Orphan
The email address of Matt Waddel is no longer working.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Alexei Fedorov <alexie.fedorov@arm.com>
2014-08-30 07:46:39 -04:00
Masahiro Yamada
93d4334f7f Add board MAINTAINERS files
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.

The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.

After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.

TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:06 -04:00
Masahiro Yamada
dd84058d24 kconfig: add board Kconfig and defconfig files
This commit adds:
 - arch/${ARCH}/Kconfig
    provide a menu to select target boards
 - board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
    set CONFIG macros to the appropriate values for each board
 - configs/${TARGET_BOARD}_defconfig
    default setting of each board

(This commit was automatically generated by a conversion script
based on boards.cfg)

In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.

But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-07-30 08:48:01 -04:00
Darwin Rambo
261d27605c arm: Add support for semihosting for armv8 fastmodel targets.
The armv8 ARM Trusted Firmware (ATF) can be used to load various ATF
images and u-boot, and does this for virtual platforms by using
semihosting. This commit extends this idea by allowing u-boot to also
use semihosting to load the kernel/ramdisk/dtb. This eliminates the need
for a bootwrapper and produces a more realistic boot sequence with
virtual models.

Though the semihosting code is quite generic, support for armv7 in
fastmodel is less useful due to the wide range of available silicon
and the lack of a free armv7 fastmodel, so this change contains an
untested armv7 placeholder for the service trap opcode.

Please refer to doc/README.semihosting for a more detailed description
of semihosting and how it is used with the armv8 virtual platforms.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Cc: trini@ti.com
Cc: fenghua@phytium.com.cn
Cc: bhupesh.sharma@freescale.com
2014-07-03 08:35:45 +02:00
Albert ARIBAUD
b60eff31f3 arm: remove unneeded symbol offsets and _TEXT_BASE
Remove the last uses of symbol offsets in ARM U-Boot.
Remove some needless uses of _TEXT_BASE.
Remove all _TEXT_BASE definitions.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-02-26 21:18:12 +01:00
Albert ARIBAUD
c0cae2e245 Merge branch 'u-boot-arm/next' into 'u-boot-arm/master' 2014-01-28 11:25:28 +01:00
Darwin Rambo
de351d6be6 lib: time: add weak timer_init() function
If timer_init() is made a weak stub function, then it allows us to
remove several empty timer_init functions for those boards that
already have a timer initialized when u-boot starts. Architectures
that use the timer framework may also remove the need for timer.c.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
2014-01-24 16:59:06 -05:00
Linus Walleij
a25feb7a6d ARM: versatile: pass correct machine type for Versatile AB
When U-Boot is configured for Versatile AB, it will still pass
the machine ID of Versatile PB to the kernel. After this simple
fix the system boots correctly.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
2014-01-13 09:46:08 +01:00
David Feng
129168290a arm64: board support of vexpress_aemv8a
Signed-off-by: David Feng <fenghua@phytium.com.cn>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
2014-01-09 16:08:58 +01:00
Rob Herring
b3a7f22b3e ARM: vexpress: convert to common timer code
Convert vexpress to use the commmon timer code.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:23:45 -05:00
Masahiro Yamada
a79854a90f board: arm: convert makefiles to Kbuild style
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Tom Rini <trini@ti.com>
2013-11-01 11:42:12 -04:00
Wolfgang Denk
3765b3e7bd Coding Style cleanup: remove trailing white space
Signed-off-by: Wolfgang Denk <wd@denx.de>
2013-10-14 16:06:53 -04:00
Andre Przywara
e261c83aa0 ARM: VExpress: enable ARMv7 virt support for VExpress A15
To enable hypervisors utilizing the ARMv7 virtualization extension
on the Versatile Express board with the A15 core tile, we add the
required configuration variable.
Also we define the board specific smp_set_cpu_boot_addr() function to
set the start address for secondary cores in the VExpress specific
manner.
There is no need to provide a custom smp_waitloop() function here.

This also serves as an example for what to do when adding support for
new boards.

Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
2013-10-03 21:28:57 +02:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00