Commit graph

297 commits

Author SHA1 Message Date
Masahiro Yamada
c79cba37b3 cosmetic: replace MIN, MAX with min, max
The macro MIN, MAX is defined as the aliase of min, max,
respectively.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-24 18:30:29 -04:00
Masahiro Yamada
ed36323f6d kconfig: add blank Kconfig files
This would be useful to start moving various config options.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2014-09-24 18:30:28 -04:00
Wang Huan
df0a5b880d ls102xa: i2c: Add i2c support for LS102xA
The existing i.MX's I2C driver mxc_i2c.c is compatible
with the controller of LS102xA. As I2C's registers
are 8-bit on LS102xA, I2C_QUIRK_REG is enabled to
use 8-bit driver.

This patch is to add I2C 1,2,3 support for LS102xA.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
2014-09-08 10:30:32 -07:00
Albert ARIBAUD
740f41d3cb Merge branch 'u-boot-sunxi/master' into 'u-boot-arm/master' 2014-07-28 10:12:45 +02:00
Hans de Goede
6620377e4b sunxi: Add i2c support
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
2014-07-18 19:41:30 +01:00
Hans de Goede
0db2bbdc04 mvtwsi: convert to CONFIG_SYS_I2C framework
Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).

The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Schocher <hs@denx.de>
2014-07-16 19:56:24 +01:00
Shengzhou Liu
a17fd10fb5 fsl_i2c: add support for 3rd and 4th I2C
Add support for 3rd and 4th I2C.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
2014-07-16 05:19:15 +02:00
Heiko Schocher
f7c1053535 i2c, omap24xx: add i2c deblock sequenz
If a bus busy is detected when intializing the driver,
toggle 9 times the scl pin. Therefore enable the test mode
of the controller, in which the scl, sda pins can be
controlled manually.

Tested on the siemens boards pxm2, rut and dxr2.

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: Lubomir Popov <lpopov@mm-sol.com>
Cc: Steve Sakoman <steve@sakoman.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Vincent Stehlé <v-stehle@ti.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
2014-07-16 05:18:55 +02:00
Dirk Eibach
3a990bfaea board: gdsys: Make gdsys osd hardware detection more robust
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2014-07-07 19:47:19 -04:00
Dirk Eibach
b46226bdb5 i2c: IHS I2C master driver
IHS I2C master support was merely a hack in the osd driver.
Now it is a proper u-boot I2C framework driver, supporting the
v2.00 master features.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
2014-07-07 19:47:18 -04:00
Tom Rini
6ee3d00d1d Merge branch 'master' of git://git.denx.de/u-boot-i2c 2014-07-07 10:10:52 -04:00
York Sun
2f78eae506 ARMv8/FSL_LSCH3: Add FSL_LSCH3 SoC
Freescale LayerScape with Chassis Generation 3 is a set of SoCs with
ARMv8 cores and 3rd generation of Chassis. We use different MMU setup
to support memory map and cache attribute for these SoCs. MMU and cache
are enabled very early to bootst performance, especially for early
development on emulators. After u-boot relocates to DDR, a new MMU
table with QBMan cache access is created in DDR. SMMU pagesize is set
in SMMU_sACR register. Both DDR3 and DDR4 are supported.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
2014-07-03 08:40:51 +02:00
Stephen Warren
ad3091ad03 i2c: tegra: dump alen in debug statements
Since tegra_i2c_{read,write}'s debug() call dumps the chip address, dump
the address length (alen) too, so the address value can be correctly
interpreted.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
2014-07-03 06:29:39 +02:00
Stephen Warren
981b14f01a i2c: tegra: write clean data to TX FIFO
The Tegra I2C controller's TX FIFO contains 32-bit words. If the final
FIFO entry of a transaction contains fewer than 4 bytes, the driver
currently fills the unused FIFO bytes with uninitialized data. This can
be confusing when reading back the FIFO content for debugging purposes.

Solve this by explicitly initializing the variable containing FIFO data
before filling it (partially) with data. With this change,
send_recv_packets()'s loop's if (is_write) code mirrors the else (i.e.
read) branch.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
2014-07-03 06:29:31 +02:00
Stephen Warren
68049a082b i2c: tegra: use repeated start for reads
I2C read transactions are typically implemented as follows:

START(write) address REPEATED_START(read) data... STOP

However, Tegra's I2C driver currently implements reads as follows:

START(write) address STOP START(read) data... STOP

This sequence confuses at least the AS3722 PMIC on the Jetson TK1 board,
leading to corrupted read data in some cases. Fix the driver to chain
the transactions together using repeated starts to solve this.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Yen Lin <yelin@nvidia.com>
2014-07-03 06:29:19 +02:00
Steve Rae
6736ec15c5 i2c: kona: Resolve Kona I2C driver issue
- "i2c mw" command hangs (with some compilers)

Signed-off-by: Steve Rae <srae@broadcom.com>
2014-06-12 11:42:50 +02:00
Hans de Goede
2072e72629 mvtwsi: Remove unnecessary twsi_baud_rate and twsi_slave_address globals
These are used only once, so their is no need to have them global.

This also stops mvtwsi from using any bss vars making it easier to use
before dram init (to talk to the pmic to set the dram voltage).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-05-14 12:59:12 +02:00
Hans de Goede
fab356a0b8 mvtwsi: Fix clock programming
The TWSI_FREQUENCY macro was wrong in 2 ways:
1) It was casting the result of the calculations to an u8, while i2c clk
rates are often >= 100Khz which won't fit in a u8, drop the cast.
2) It had an extra factor of 2 in the divider which neither the datasheet nor
the Linux driver have.

The comment for the default value was wrongly saying that m lives in
bits 4-7, while in reality it is in bits 3-6, as can be seen from the correct
shift by 3 used in i2c_init().

While at it remove the unused twsi_actual_speed variable.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-05-14 12:58:55 +02:00
Tom Rini
bcb879c0e3 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-05-09 11:18:45 -04:00
Albert ARIBAUD
d2a3e91139 Merge branch 'u-boot/master'
Conflicts:
	drivers/net/Makefile

(trivial merge)
2014-05-09 11:50:14 +02:00
Jesper B. Christensen
5146fc2b37 i2c: zynq: Fixed compilation errors when using DEBUG
Signed-off-by: Jesper B. Christensen <jesper.christensen@cobham.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-05-08 07:03:37 +02:00
Shaveta Leekha
a405764c1e drivers/i2c/fsl_i2c: modify i2c_read to handle multi-byte write
Most of the I2C slaves support accesses in the typical style
that is : read/write series of bytes at particular address offset.
These transactions look like:"
(1) START:Address:Tx:Offset:RESTART:Address[0..4]:Tx/Rx:data[0..n]:STOP"

However there are certain devices which support accesses in
terms of the transactions as follows:
(2) "START:Address:Tx:Txdata[0..n1]:Clock_stretching:
        RESTART:Address:Rx:data[0..n2]"
Here Txdata is typically a command and some associated data,
similarly Rxdata could be command status plus some data received
as a response to the command sent.

Type (1) transactions are currently supportd in the
i2c driver using i2c_read and i2c_write APIs. I2C EEPROMs,
RTC, etc fall in this category.

To handle type (2) along with type (1) transactions,
i2c_read() function has been modified.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
2014-04-29 07:10:58 +02:00
York Sun
dec1861be9 driver/mxc_i2c: Move static data structure to global_data
This driver needs a data structure in SRAM before SDRAM is available.
This is not alway the case using .data section. Moving this data
structure to global_data guarantees it is writable.

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
2014-04-29 07:10:27 +02:00
Albert ARIBAUD
c9aab0f9dd Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-04-21 21:01:35 +02:00
Vitaly Andrianov
e8459dcc33 i2c, davinci: convert driver to new mutlibus/mutliadapter framework
- add davinci driver to new multibus/multiadpater support
    - adapted all config files, which uses this driver

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Heiko Schocher <hs@denx.de>
2014-04-17 17:24:38 -04:00
Karicheri, Muralidharan
356d15ebb2 i2c, davinci: move i2c_defs.h to the drivers/i2c directory
This patch moves the davinci i2c_defs.h file to drivers.i2c directory.
It will allow to reuse the davinci_i2c driver for TI Keystone2 SOCs.

Not used "git mv" command to move the file because small part of
it with definitions specific for Davinci SOCs has to remain in the
arch/arm/include/asm/arch-davinci.

Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Tom Rini <trini@ti.com>
2014-04-17 17:24:38 -04:00
Tetsuyuki Kobayashi
7a65768903 i2c: sh_i2c: bugfix: i2c probe command does not work
This is regression of commit 2035d77d i2c: sh_i2c: Update to new CONFIG_SYS_I2C framework

Before commit 2035d77d, i2c probe command works properly on kzm9g board.

KZM-A9-GT# i2c probe
Valid chip addresses: 0C 12 1D 32 39 3D 40 60

After commit 2035d77d, i2c probe command does not work.

KZM-A9-GT# i2c probe
Valid chip addresses: 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F

sh_i2c_probe() calls sh_i2c_read(), but read length is 0. So acutally it does not read device at all. This patch prepares dummy buffer and read data into it.

Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-04-14 17:41:48 +09:00
Masahiro Yamada
462d1883f7 drivers: i2c: delete an unused source file
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
2014-03-31 07:30:55 +02:00
Tom Rini
eeb72e6761 Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	arch/arm/cpu/armv7/config.mk
	board/ti/am43xx/mux.c
	include/configs/am43xx_evm.h

Signed-off-by: Tom Rini <trini@ti.com>
2014-02-26 16:49:58 -05:00
Darwin Rambo
4bded3a367 i2c: kona: Add Kona I2C driver
Add support for the Kona I2C controller found on Broadcom mobile SoCs.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Tim Kryger <tkryger@linaro.org>
2014-02-22 19:30:39 +01:00
Tom Rini
6853e6aa77 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-02-20 12:18:59 -05:00
Alexey Brodkin
3d93f6959b designware_i2c: remove inclusion of <asm/arch/hardware.h>
As soon as all boards have their CONFIG_SYS_I2C_BASE defined in
configuration files instead of "asm/arch/hardware.h" it's safe to remove
the inclusion in question and make driver platform-independent.

Cc: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Armando Visconti <armando.visconti@st.com>

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
2014-02-20 06:49:09 +01:00
Hannes Petermaier
d5243359e1 OMAP24xx I2C: Add support for set-speed
Adds support for set-speed on the OMAP24xx I2C Adapter.

Changes to omap24_i2c_write(...) for polling ARDY Bit from IRQ-Status.
Otherwise on a subsequent call the transfer of last byte from the
predecessor is aborted and therefore lost. For exmaple when
i2c_write(...) is followed by a i2c_setspeed(...) (which has to
deactivate and activate master for changing psc,...).

Minor cosmetical changes.

Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Cc: Heiko Schocher <hs@denx.de>
2014-02-20 06:48:23 +01:00
Marek Vasut
d22643e7e8 i2c: i2c-mxs: Wait for I2C to empty queue
Make sure the I2C write queue is empty before leaving the mxs_i2c_write().
If we start and I2C write and only wait for ACK, the MXS I2C IP block may
enter next operation while still processing the write aftermath internally.
This will in turn disrupt one or more subsequent transfer(s).

A testcase for this issue is as such. This testcase is also interesting because
the first I2C_WRITE which becomes disruptive happens in the 'i2c read' command.
The 'i2c read' command first uses I2C_WRITE to send I2C address of the chip and
then uses I2C_READ to read data from the chip. After this command completes, the
'i2c probe' will use sequence of I2C_WRITE commands to probe the I2C bus. The
problem is that the first I2C_WRITE disrupted the I2C IP block operation and
this sideeffect propagates all the way to this next I2C_WRITE used by the 'i2c
probe' call. The result is the 'i2c probe' receives an ACK on I2C address 0x00,
even if this ACK was owned by the previous I2C_WRITE operation. Note that the
'i2c read' command must read from a valid I2C chip address.

Wrong:
> i2c probe
Valid chip addresses: 50 51
> i2c read 0x50 0x0.2 0x10 0x42000000
> i2c probe
Valid chip addresses: 00 50 51

With this patch
> i2c probe
Valid chip addresses: 50 51
> i2c read 0x50 0x0.2 0x10 0x42000000
> i2c probe
Valid chip addresses: 50 51

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
2014-02-20 06:46:57 +01:00
Chin Liang See
070cbaf821 designware_i2c: Enhance DesignWare I2C driver address support
Enhance the DesignWare I2C driver to support address length more
than 1 byte. This enhancement is required as some I2C slave
device such as EEPROM chip might have 16 bit address byte.

Signed-off-by: Chin Liang See <clsee@altera.com>
Acked-by: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
2014-02-20 06:46:56 +01:00
Scott Jiang
16c550274c blackfin: make i2c driver blackfin independant
The ADI twi peripheral is not binding to Blackfin processor only.
Access i2c registers by standard io functions.
Fix coding style.

Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-02-20 06:46:56 +01:00
Sonic Zhang
86bdd70a09 blackfin: rename bfin-twi_i2c driver to adi_i2c
The ADI twi peripheral is not binding to Blackfin processor only.
Change to a generic name.

Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-02-20 06:46:56 +01:00
Sonic Zhang
d6a320d5bb blackfin: add spi and i2c specific get clock functions
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-02-20 06:46:56 +01:00
Sonic Zhang
bb0fad0ea0 blackfin: the sclk MHz in i2c driver should be divided by 1000 other than 1024
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2014-02-20 06:46:55 +01:00
Michael Burr
18948632a9 i2c: zynq: Add support for the second i2c controller
Initialize the second i2c controller.

Signed-off-by: Michael Burr <michael.burr@logicpd.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-20 06:46:55 +01:00
Michael Burr
9e90107155 i2c: zynq: Support for 0-length register address
Fixed bug with alen == 0 in 'i2c_write', 'i2c_read'
Further minor corrections:
- Write 'address' register before 'data' register.
- Write 'transfer_size' register before 'address' register.

Signed-off-by: Michael Burr <michael.burr@logicpd.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2014-02-20 06:46:55 +01:00
Marek Vasut
c8d4b2f826 ARM: IXP: Remove the IXP architecture support
The architecture is unmaintained and dead, remove it.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
2014-02-06 02:51:52 +01:00
Kuo-Jung Su
dccacbe019 i2c: fti2c010: fix compiler warning on paddr[]
This fixes the following compiler warnings:

fti2c010.c: In function 'fti2c010_read':
fti2c010.c:204:8: warning: 'paddr' may be used uninitialized in this function [-Wuninitialized]
fti2c010.c: In function 'fti2c010_write':
fti2c010.c:266:8: warning: 'paddr' may be used uninitialized in this function [-Wuninitialized]

Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Heiko Schocher <hs@denx.de>
2014-01-13 08:18:38 +01:00
Alexey Brodkin
32d041e218 drivers/designware_i2c - add suppor of CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
Since we agreed on legacy implementation of "eeprom_{read|write}"
(http://patchwork.ozlabs.org/patch/295825/) I had to fix/make it work
again DesignWare I2C driver for cases when 1 EEPROM IC fake I2C with
anumber of "built-in" ICs with different chip addresses.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>

Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin KUMAR <vipin.kumar@st.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
2014-01-13 08:18:13 +01:00
Darwin Rambo
7cc1b02f8f i2c: Fix i2c speed command
This corrects i2c core to interpret the value returned by
i2c_set_bus_speed as a success indicator rather than the
actual speed that was set. When i2c_set_bus_speed returns
a failure code, the speed is unknown so the adapter speed
is set to zero.

Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Steve Rae <srae@broadcom.com>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-01-13 08:17:51 +01:00
Nobuhiro Iwamatsu
da1ed0d20e rcar_i2c: Clear status before start master receive
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-01-13 08:16:48 +01:00
Hisashi Nakamura
ad5e14ecdd rcar_i2c: Fix receiving wait condition
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-01-13 08:16:22 +01:00
Alban Bedel
ac2ff538cd i2c: tegra: Add the fifth bus on SoC with more than 4 buses
Create the i2c adapter object for the fifth bus on SoC with more than
4 buses. This allow using all the bus available on T30.

Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2013-12-18 10:19:49 -07:00
Tom Rini
4b210ad342 Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	board/samsung/trats2/trats2.c
	include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini <trini@ti.com>
2013-12-10 17:15:18 -05:00
Albert ARIBAUD
f15ea6e1d6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds
2013-12-10 22:23:59 +01:00