u-boot/arch/arm/dts/imx6qdl-dhcom-pdk2-u-boot.dtsi

// SPDX-License-Identifier: (GPL-2.0+)
/*
 * Copyright (C) 2020 Harald Seiler <hws@denx.de>
 */

#include "imx6qdl-dhcom-u-boot.dtsi"

&fec {
	phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
};
ARM: imx6: DHCOM i.MX6 PDK: Convert to DM_ETH Use DM_ETH instead of legacy networking. Add VIO as a fixed regulator to the relevant device-trees and augment the FEC node with properties for the reset GPIO. It should be noted that the relevant properties for the reset GPIO already exist in the PHY node (reset-gpios, reset-delay-us, reset-post-delay-us) but U-Boot currently ignores those and only supports the bus-level reset properties in the FEC node (phy-reset-gpios, phy-reset-duration, phy-reset-post-delay). Signed-off-by: Harald Seiler <hws@denx.de> 2020-04-15 18:04:53 +00:00			`// SPDX-License-Identifier: (GPL-2.0+)`
			`/*`
			`* Copyright (C) 2020 Harald Seiler <hws@denx.de>`
			`*/`

ARM: imx6: DHCOM i.MX6 PDK: Fix usb-otg VBUS regulator During the conversion of this board to DM_REGULATOR, usb-mass-storage was broken and started failing with the following error: => ums 0 mmc 2 UMS: LUN 0, dev 2, hwpart 0, sector 0x0, count 0xe90000 Error enabling VBUS supply g_dnl_register: failed!, error: -38 g_dnl_register failed Fix this by adding the relevant GPIO to the regulator node. Fixes: 4ca99fe81aea ("ARM: imx: dh-imx6: Enable DM regulator") Signed-off-by: Harald Seiler <hws@denx.de> 2020-04-16 08:52:19 +00:00			`#include "imx6qdl-dhcom-u-boot.dtsi"`

ARM: imx6: DHCOM i.MX6 PDK: Convert to DM_ETH Use DM_ETH instead of legacy networking. Add VIO as a fixed regulator to the relevant device-trees and augment the FEC node with properties for the reset GPIO. It should be noted that the relevant properties for the reset GPIO already exist in the PHY node (reset-gpios, reset-delay-us, reset-post-delay-us) but U-Boot currently ignores those and only supports the bus-level reset properties in the FEC node (phy-reset-gpios, phy-reset-duration, phy-reset-post-delay). Signed-off-by: Harald Seiler <hws@denx.de> 2020-04-15 18:04:53 +00:00			`&fec {`
ARM: dts: imx6q-dhcom: Use 1G ethernet on the PDK2 board The PDK2 board is capable of running both 100M and 1G ethernet. However, the i.MX6 has only one ethernet MAC, so it is possible to configure either 100M or 1G Ethernet. In case of 100M option, the PHY is on the SoM and the signals are routed to a RJ45 port. For 1G the PHY is on the PDK2 board with another RJ45 port. 100M and 1G ethernet use different signal pins from the i.MX6, but share the MDIO bus. This SoM board combination is used to demonstrate how to enable 1G ethernet configuration. Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com> Cc: Stefano Babic <sbabic@denx.de> 2021-11-28 02:53:18 +00:00			`phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;`
ARM: imx6: DHCOM i.MX6 PDK: Convert to DM_ETH Use DM_ETH instead of legacy networking. Add VIO as a fixed regulator to the relevant device-trees and augment the FEC node with properties for the reset GPIO. It should be noted that the relevant properties for the reset GPIO already exist in the PHY node (reset-gpios, reset-delay-us, reset-post-delay-us) but U-Boot currently ignores those and only supports the bus-level reset properties in the FEC node (phy-reset-gpios, phy-reset-duration, phy-reset-post-delay). Signed-off-by: Harald Seiler <hws@denx.de> 2020-04-15 18:04:53 +00:00			`};`