u-boot/drivers/pci/pci.c

794 lines
18 KiB
C
Raw Normal View History

2002-11-03 00:24:07 +00:00
/*
* (C) Copyright 2001 Sysgo Real-Time Solutions, GmbH <www.elinos.com>
* Andreas Heppel <aheppel@sysgo.de>
*
* (C) Copyright 2002, 2003
2002-11-03 00:24:07 +00:00
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
2002-11-03 00:24:07 +00:00
*/
/*
* PCI routines
*/
#include <common.h>
#include <command.h>
#include <asm/processor.h>
#include <asm/io.h>
#include <pci.h>
#define PCI_HOSE_OP(rw, size, type) \
int pci_hose_##rw##_config_##size(struct pci_controller *hose, \
pci_dev_t dev, \
int offset, type value) \
{ \
return hose->rw##_##size(hose, dev, offset, value); \
2002-11-03 00:24:07 +00:00
}
PCI_HOSE_OP(read, byte, u8 *)
PCI_HOSE_OP(read, word, u16 *)
PCI_HOSE_OP(read, dword, u32 *)
PCI_HOSE_OP(write, byte, u8)
PCI_HOSE_OP(write, word, u16)
PCI_HOSE_OP(write, dword, u32)
#define PCI_OP(rw, size, type, error_code) \
int pci_##rw##_config_##size(pci_dev_t dev, int offset, type value) \
{ \
struct pci_controller *hose = pci_bus_to_hose(PCI_BUS(dev)); \
\
if (!hose) \
{ \
error_code; \
return -1; \
} \
\
return pci_hose_##rw##_config_##size(hose, dev, offset, value); \
2002-11-03 00:24:07 +00:00
}
PCI_OP(read, byte, u8 *, *value = 0xff)
PCI_OP(read, word, u16 *, *value = 0xffff)
PCI_OP(read, dword, u32 *, *value = 0xffffffff)
PCI_OP(write, byte, u8, )
PCI_OP(write, word, u16, )
PCI_OP(write, dword, u32, )
#define PCI_READ_VIA_DWORD_OP(size, type, off_mask) \
int pci_hose_read_config_##size##_via_dword(struct pci_controller *hose,\
pci_dev_t dev, \
int offset, type val) \
{ \
u32 val32; \
\
if (pci_hose_read_config_dword(hose, dev, offset & 0xfc, &val32) < 0) { \
*val = -1; \
return -1; \
} \
\
*val = (val32 >> ((offset & (int)off_mask) * 8)); \
\
return 0; \
2002-11-03 00:24:07 +00:00
}
#define PCI_WRITE_VIA_DWORD_OP(size, type, off_mask, val_mask) \
int pci_hose_write_config_##size##_via_dword(struct pci_controller *hose,\
pci_dev_t dev, \
int offset, type val) \
{ \
u32 val32, mask, ldata, shift; \
\
if (pci_hose_read_config_dword(hose, dev, offset & 0xfc, &val32) < 0)\
return -1; \
\
shift = ((offset & (int)off_mask) * 8); \
ldata = (((unsigned long)val) & val_mask) << shift; \
mask = val_mask << shift; \
val32 = (val32 & ~mask) | ldata; \
\
if (pci_hose_write_config_dword(hose, dev, offset & 0xfc, val32) < 0)\
return -1; \
\
return 0; \
2002-11-03 00:24:07 +00:00
}
PCI_READ_VIA_DWORD_OP(byte, u8 *, 0x03)
PCI_READ_VIA_DWORD_OP(word, u16 *, 0x02)
PCI_WRITE_VIA_DWORD_OP(byte, u8, 0x03, 0x000000ff)
PCI_WRITE_VIA_DWORD_OP(word, u16, 0x02, 0x0000ffff)
/* Get a virtual address associated with a BAR region */
void *pci_map_bar(pci_dev_t pdev, int bar, int flags)
{
pci_addr_t pci_bus_addr;
u32 bar_response;
/* read BAR address */
pci_read_config_dword(pdev, bar, &bar_response);
pci_bus_addr = (pci_addr_t)(bar_response & ~0xf);
/*
* Pass "0" as the length argument to pci_bus_to_virt. The arg
* isn't actualy used on any platform because u-boot assumes a static
* linear mapping. In the future, this could read the BAR size
* and pass that as the size if needed.
*/
return pci_bus_to_virt(pdev, pci_bus_addr, flags, 0, MAP_NOCACHE);
}
2002-11-03 00:24:07 +00:00
/*
*
*/
static struct pci_controller* hose_head;
2002-11-03 00:24:07 +00:00
void pci_register_hose(struct pci_controller* hose)
{
struct pci_controller **phose = &hose_head;
while(*phose)
phose = &(*phose)->next;
hose->next = NULL;
*phose = hose;
}
struct pci_controller *pci_bus_to_hose(int bus)
2002-11-03 00:24:07 +00:00
{
struct pci_controller *hose;
for (hose = hose_head; hose; hose = hose->next) {
if (bus >= hose->first_busno && bus <= hose->last_busno)
2002-11-03 00:24:07 +00:00
return hose;
}
2002-11-03 00:24:07 +00:00
2005-10-17 00:39:53 +00:00
printf("pci_bus_to_hose() failed\n");
2002-11-03 00:24:07 +00:00
return NULL;
}
struct pci_controller *find_hose_by_cfg_addr(void *cfg_addr)
{
struct pci_controller *hose;
for (hose = hose_head; hose; hose = hose->next) {
if (hose->cfg_addr == cfg_addr)
return hose;
}
return NULL;
}
int pci_last_busno(void)
{
struct pci_controller *hose = hose_head;
if (!hose)
return -1;
while (hose->next)
hose = hose->next;
return hose->last_busno;
}
2002-11-03 00:24:07 +00:00
pci_dev_t pci_find_devices(struct pci_device_id *ids, int index)
{
struct pci_controller * hose;
u16 vendor, device;
u8 header_type;
pci_dev_t bdf;
int i, bus, found_multi = 0;
for (hose = hose_head; hose; hose = hose->next) {
#ifdef CONFIG_SYS_SCSI_SCAN_BUS_REVERSE
2002-11-03 00:24:07 +00:00
for (bus = hose->last_busno; bus >= hose->first_busno; bus--)
#else
for (bus = hose->first_busno; bus <= hose->last_busno; bus++)
#endif
for (bdf = PCI_BDF(bus, 0, 0);
#if defined(CONFIG_ELPPC) || defined(CONFIG_PPMC7XX)
bdf < PCI_BDF(bus, PCI_MAX_PCI_DEVICES - 1,
PCI_MAX_PCI_FUNCTIONS - 1);
2002-11-03 00:24:07 +00:00
#else
bdf < PCI_BDF(bus + 1, 0, 0);
2002-11-03 00:24:07 +00:00
#endif
bdf += PCI_BDF(0, 0, 1)) {
if (!PCI_FUNC(bdf)) {
2002-11-03 00:24:07 +00:00
pci_read_config_byte(bdf,
PCI_HEADER_TYPE,
&header_type);
found_multi = header_type & 0x80;
} else {
2002-11-03 00:24:07 +00:00
if (!found_multi)
continue;
}
pci_read_config_word(bdf,
PCI_VENDOR_ID,
&vendor);
pci_read_config_word(bdf,
PCI_DEVICE_ID,
&device);
for (i = 0; ids[i].vendor != 0; i++) {
2002-11-03 00:24:07 +00:00
if (vendor == ids[i].vendor &&
device == ids[i].device) {
2002-11-03 00:24:07 +00:00
if (index <= 0)
return bdf;
index--;
}
}
2002-11-03 00:24:07 +00:00
}
}
return -1;
2002-11-03 00:24:07 +00:00
}
pci_dev_t pci_find_device(unsigned int vendor, unsigned int device, int index)
{
static struct pci_device_id ids[2] = {{}, {0, 0}};
ids[0].vendor = vendor;
ids[0].device = device;
return pci_find_devices(ids, index);
}
/*
*
*/
int __pci_hose_phys_to_bus(struct pci_controller *hose,
phys_addr_t phys_addr,
unsigned long flags,
unsigned long skip_mask,
pci_addr_t *ba)
2002-11-03 00:24:07 +00:00
{
struct pci_region *res;
pci_addr_t bus_addr;
2002-11-03 00:24:07 +00:00
int i;
for (i = 0; i < hose->region_count; i++) {
2002-11-03 00:24:07 +00:00
res = &hose->regions[i];
if (((res->flags ^ flags) & PCI_REGION_TYPE) != 0)
continue;
if (res->flags & skip_mask)
continue;
2002-11-03 00:24:07 +00:00
bus_addr = phys_addr - res->phys_start + res->bus_start;
if (bus_addr >= res->bus_start &&
bus_addr < res->bus_start + res->size) {
*ba = bus_addr;
return 0;
2002-11-03 00:24:07 +00:00
}
}
return 1;
2002-11-03 00:24:07 +00:00
}
pci_addr_t pci_hose_phys_to_bus (struct pci_controller *hose,
phys_addr_t phys_addr,
unsigned long flags)
2002-11-03 00:24:07 +00:00
{
pci_addr_t bus_addr = 0;
int ret;
2002-11-03 00:24:07 +00:00
if (!hose) {
puts("pci_hose_phys_to_bus: invalid hose\n");
return bus_addr;
2002-11-03 00:24:07 +00:00
}
/*
* if PCI_REGION_MEM is set we do a two pass search with preference
* on matches that don't have PCI_REGION_SYS_MEMORY set
*/
if ((flags & PCI_REGION_MEM) == PCI_REGION_MEM) {
ret = __pci_hose_phys_to_bus(hose, phys_addr,
flags, PCI_REGION_SYS_MEMORY, &bus_addr);
if (!ret)
return bus_addr;
}
ret = __pci_hose_phys_to_bus(hose, phys_addr, flags, 0, &bus_addr);
if (ret)
puts("pci_hose_phys_to_bus: invalid physical address\n");
return bus_addr;
}
int __pci_hose_bus_to_phys(struct pci_controller *hose,
pci_addr_t bus_addr,
unsigned long flags,
unsigned long skip_mask,
phys_addr_t *pa)
{
struct pci_region *res;
int i;
for (i = 0; i < hose->region_count; i++) {
2002-11-03 00:24:07 +00:00
res = &hose->regions[i];
if (((res->flags ^ flags) & PCI_REGION_TYPE) != 0)
continue;
if (res->flags & skip_mask)
continue;
2002-11-03 00:24:07 +00:00
if (bus_addr >= res->bus_start &&
(bus_addr - res->bus_start) < res->size) {
*pa = (bus_addr - res->bus_start + res->phys_start);
return 0;
2002-11-03 00:24:07 +00:00
}
}
return 1;
}
phys_addr_t pci_hose_bus_to_phys(struct pci_controller* hose,
pci_addr_t bus_addr,
unsigned long flags)
{
phys_addr_t phys_addr = 0;
int ret;
if (!hose) {
puts("pci_hose_bus_to_phys: invalid hose\n");
return phys_addr;
}
/*
* if PCI_REGION_MEM is set we do a two pass search with preference
* on matches that don't have PCI_REGION_SYS_MEMORY set
*/
if ((flags & PCI_REGION_MEM) == PCI_REGION_MEM) {
ret = __pci_hose_bus_to_phys(hose, bus_addr,
flags, PCI_REGION_SYS_MEMORY, &phys_addr);
if (!ret)
return phys_addr;
}
ret = __pci_hose_bus_to_phys(hose, bus_addr, flags, 0, &phys_addr);
if (ret)
puts("pci_hose_bus_to_phys: invalid physical address\n");
2002-11-03 00:24:07 +00:00
return phys_addr;
2002-11-03 00:24:07 +00:00
}
/*
*
*/
int pci_hose_config_device(struct pci_controller *hose,
pci_dev_t dev,
unsigned long io,
pci_addr_t mem,
2002-11-03 00:24:07 +00:00
unsigned long command)
{
u32 bar_response;
unsigned int old_command;
pci_addr_t bar_value;
pci_size_t bar_size;
2002-11-03 00:24:07 +00:00
unsigned char pin;
int bar, found_mem64;
debug("PCI Config: I/O=0x%lx, Memory=0x%llx, Command=0x%lx\n", io,
(u64)mem, command);
2002-11-03 00:24:07 +00:00
pci_hose_write_config_dword(hose, dev, PCI_COMMAND, 0);
2002-11-03 00:24:07 +00:00
for (bar = PCI_BASE_ADDRESS_0; bar <= PCI_BASE_ADDRESS_5; bar += 4) {
pci_hose_write_config_dword(hose, dev, bar, 0xffffffff);
pci_hose_read_config_dword(hose, dev, bar, &bar_response);
2002-11-03 00:24:07 +00:00
if (!bar_response)
continue;
found_mem64 = 0;
/* Check the BAR type and set our address mask */
if (bar_response & PCI_BASE_ADDRESS_SPACE) {
2002-11-03 00:24:07 +00:00
bar_size = ~(bar_response & PCI_BASE_ADDRESS_IO_MASK) + 1;
/* round up region base address to a multiple of size */
2002-11-03 00:24:07 +00:00
io = ((io - 1) | (bar_size - 1)) + 1;
bar_value = io;
/* compute new region base address */
io = io + bar_size;
} else {
if ((bar_response & PCI_BASE_ADDRESS_MEM_TYPE_MASK) ==
PCI_BASE_ADDRESS_MEM_TYPE_64) {
u32 bar_response_upper;
u64 bar64;
pci_hose_write_config_dword(hose, dev, bar + 4,
0xffffffff);
pci_hose_read_config_dword(hose, dev, bar + 4,
&bar_response_upper);
bar64 = ((u64)bar_response_upper << 32) | bar_response;
2002-11-03 00:24:07 +00:00
bar_size = ~(bar64 & PCI_BASE_ADDRESS_MEM_MASK) + 1;
found_mem64 = 1;
} else {
bar_size = (u32)(~(bar_response & PCI_BASE_ADDRESS_MEM_MASK) + 1);
}
2002-11-03 00:24:07 +00:00
/* round up region base address to multiple of size */
2002-11-03 00:24:07 +00:00
mem = ((mem - 1) | (bar_size - 1)) + 1;
bar_value = mem;
/* compute new region base address */
mem = mem + bar_size;
2002-11-03 00:24:07 +00:00
}
/* Write it out and update our limit */
pci_hose_write_config_dword (hose, dev, bar, (u32)bar_value);
2002-11-03 00:24:07 +00:00
if (found_mem64) {
2002-11-03 00:24:07 +00:00
bar += 4;
#ifdef CONFIG_SYS_PCI_64BIT
pci_hose_write_config_dword(hose, dev, bar,
(u32)(bar_value >> 32));
#else
pci_hose_write_config_dword(hose, dev, bar, 0x00000000);
#endif
2002-11-03 00:24:07 +00:00
}
}
/* Configure Cache Line Size Register */
pci_hose_write_config_byte(hose, dev, PCI_CACHE_LINE_SIZE, 0x08);
2002-11-03 00:24:07 +00:00
/* Configure Latency Timer */
pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, 0x80);
2002-11-03 00:24:07 +00:00
/* Disable interrupt line, if device says it wants to use interrupts */
pci_hose_read_config_byte(hose, dev, PCI_INTERRUPT_PIN, &pin);
if (pin != 0) {
pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, 0xff);
2002-11-03 00:24:07 +00:00
}
pci_hose_read_config_dword(hose, dev, PCI_COMMAND, &old_command);
pci_hose_write_config_dword(hose, dev, PCI_COMMAND,
(old_command & 0xffff0000) | command);
2002-11-03 00:24:07 +00:00
return 0;
}
/*
*
*/
struct pci_config_table *pci_find_config(struct pci_controller *hose,
unsigned short class,
unsigned int vendor,
unsigned int device,
unsigned int bus,
unsigned int dev,
unsigned int func)
{
struct pci_config_table *table;
for (table = hose->config_table; table && table->vendor; table++) {
2002-11-03 00:24:07 +00:00
if ((table->vendor == PCI_ANY_ID || table->vendor == vendor) &&
(table->device == PCI_ANY_ID || table->device == device) &&
(table->class == PCI_ANY_ID || table->class == class) &&
(table->bus == PCI_ANY_ID || table->bus == bus) &&
(table->dev == PCI_ANY_ID || table->dev == dev) &&
(table->func == PCI_ANY_ID || table->func == func)) {
2002-11-03 00:24:07 +00:00
return table;
}
}
return NULL;
}
void pci_cfgfunc_config_device(struct pci_controller *hose,
pci_dev_t dev,
struct pci_config_table *entry)
{
pci_hose_config_device(hose, dev, entry->priv[0], entry->priv[1],
entry->priv[2]);
2002-11-03 00:24:07 +00:00
}
void pci_cfgfunc_do_nothing(struct pci_controller *hose,
pci_dev_t dev, struct pci_config_table *entry)
{
}
/*
* HJF: Changed this to return int. I think this is required
* to get the correct result when scanning bridges
*/
extern int pciauto_config_device(struct pci_controller *hose, pci_dev_t dev);
2002-11-03 00:24:07 +00:00
pci: Clean up PCI info when CONFIG_PCI_SCAN_SHOW This change does the following: - Removes the printing of the PCI interrupt line value. This is normally set to 0 by U-Boot on bootup and is rarely used during everyday operation. - Prints out the PCI function number of a device. Previously a device with multiple functions would be printed identically 2 times, which is generally confusing. For example, on an Intel 2 port gigabit Ethernet card the following was displayed: ... 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 ... - Prints a text description of each device's PCI class instead of the raw PCI class code. The textual description makes it much easier to determine what devices are installed on a PCI bus. - Changes the general formatting of the PCI device output. Previous output: PCIE1: connected as Root Complex 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 03 00 10b5 8112 0604 00 02 01 10b5 8518 0604 00 02 02 10b5 8518 0604 00 08 00 1957 0040 0b20 00 07 00 10b5 8518 0604 00 09 00 10b5 8112 0604 00 07 01 10b5 8518 0604 00 07 02 10b5 8518 0604 00 06 00 10b5 8518 0604 00 02 03 10b5 8518 0604 00 01 00 10b5 8518 0604 00 PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d 00 1957 0040 0b20 00 PCIE2: Bus 0c - 0d Updated output: PCIE1: connected as Root Complex 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 03:00.0 - 10b5:8112 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 02:02.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:00.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:01.0 - 10b5:8518 - Bridge device 07:02.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 01:00.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:27 +00:00
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI_SCAN_SHOW)
const char * pci_class_str(u8 class)
{
switch (class) {
case PCI_CLASS_NOT_DEFINED:
return "Build before PCI Rev2.0";
break;
case PCI_BASE_CLASS_STORAGE:
return "Mass storage controller";
break;
case PCI_BASE_CLASS_NETWORK:
return "Network controller";
break;
case PCI_BASE_CLASS_DISPLAY:
return "Display controller";
break;
case PCI_BASE_CLASS_MULTIMEDIA:
return "Multimedia device";
break;
case PCI_BASE_CLASS_MEMORY:
return "Memory controller";
break;
case PCI_BASE_CLASS_BRIDGE:
return "Bridge device";
break;
case PCI_BASE_CLASS_COMMUNICATION:
return "Simple comm. controller";
break;
case PCI_BASE_CLASS_SYSTEM:
return "Base system peripheral";
break;
case PCI_BASE_CLASS_INPUT:
return "Input device";
break;
case PCI_BASE_CLASS_DOCKING:
return "Docking station";
break;
case PCI_BASE_CLASS_PROCESSOR:
return "Processor";
break;
case PCI_BASE_CLASS_SERIAL:
return "Serial bus controller";
break;
case PCI_BASE_CLASS_INTELLIGENT:
return "Intelligent controller";
break;
case PCI_BASE_CLASS_SATELLITE:
return "Satellite controller";
break;
case PCI_BASE_CLASS_CRYPT:
return "Cryptographic device";
break;
case PCI_BASE_CLASS_SIGNAL_PROCESSING:
return "DSP";
break;
case PCI_CLASS_OTHERS:
return "Does not fit any class";
break;
default:
return "???";
break;
};
}
#endif /* CONFIG_CMD_PCI || CONFIG_PCI_SCAN_SHOW */
int __pci_skip_dev(struct pci_controller *hose, pci_dev_t dev)
{
/*
* Check if pci device should be skipped in configuration
*/
if (dev == PCI_BDF(hose->first_busno, 0, 0)) {
#if defined(CONFIG_PCI_CONFIG_HOST_BRIDGE) /* don't skip host bridge */
/*
* Only skip configuration if "pciconfighost" is not set
*/
if (getenv("pciconfighost") == NULL)
return 1;
#else
return 1;
#endif
}
return 0;
}
int pci_skip_dev(struct pci_controller *hose, pci_dev_t dev)
__attribute__((weak, alias("__pci_skip_dev")));
#ifdef CONFIG_PCI_SCAN_SHOW
int __pci_print_dev(struct pci_controller *hose, pci_dev_t dev)
{
if (dev == PCI_BDF(hose->first_busno, 0, 0))
return 0;
return 1;
}
int pci_print_dev(struct pci_controller *hose, pci_dev_t dev)
__attribute__((weak, alias("__pci_print_dev")));
#endif /* CONFIG_PCI_SCAN_SHOW */
2002-11-03 00:24:07 +00:00
int pci_hose_scan_bus(struct pci_controller *hose, int bus)
{
unsigned int sub_bus, found_multi = 0;
2002-11-03 00:24:07 +00:00
unsigned short vendor, device, class;
unsigned char header_type;
#ifndef CONFIG_PCI_PNP
2002-11-03 00:24:07 +00:00
struct pci_config_table *cfg;
#endif
2002-11-03 00:24:07 +00:00
pci_dev_t dev;
pci: Use intelligent indentation for CONFIG_PCI_SCAN_SHOW When CONFIG_PCI_SCAN_SHOW is defined U-Boot prints out PCI devices as they are found during bootup, eg: PCIE1: connected as Root Complex 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 03:00.0 - 10b5:8112 - Bridge device 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 07:00.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:01.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:02.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d This information is useful, but its difficult to determine the PCI bus topology. To things clearer, we can use indention to make it more obvious how the PCI bus is organized. For the example above, the updated output with this change is: PCIE1: connected as Root Complex 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 03:00.0 - 10b5:8112 - Bridge device 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 07:00.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:01.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:02.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d In the examples above, an MPC8640 is connected to a PEX8518 PCIe switch (01:00 and 02:0x), which is connected to another PEX8518 PCIe switch (06:00 and 07:0x), which then connects to a MPC8572 processor (08:00). Also, the MPC8640's PEX8518 PCIe switch is connected to a PCI ethernet card (04:01) via a PEX8112 PCIe-to-PCI bridge (03:00). Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:29 +00:00
#ifdef CONFIG_PCI_SCAN_SHOW
static int indent = 0;
#endif
2002-11-03 00:24:07 +00:00
sub_bus = bus;
for (dev = PCI_BDF(bus,0,0);
dev < PCI_BDF(bus, PCI_MAX_PCI_DEVICES - 1,
PCI_MAX_PCI_FUNCTIONS - 1);
dev += PCI_BDF(0, 0, 1)) {
if (pci_skip_dev(hose, dev))
continue;
2002-11-03 00:24:07 +00:00
if (PCI_FUNC(dev) && !found_multi)
continue;
pci_hose_read_config_byte(hose, dev, PCI_HEADER_TYPE, &header_type);
pci_hose_read_config_word(hose, dev, PCI_VENDOR_ID, &vendor);
pci: Clean up PCI info when CONFIG_PCI_SCAN_SHOW This change does the following: - Removes the printing of the PCI interrupt line value. This is normally set to 0 by U-Boot on bootup and is rarely used during everyday operation. - Prints out the PCI function number of a device. Previously a device with multiple functions would be printed identically 2 times, which is generally confusing. For example, on an Intel 2 port gigabit Ethernet card the following was displayed: ... 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 ... - Prints a text description of each device's PCI class instead of the raw PCI class code. The textual description makes it much easier to determine what devices are installed on a PCI bus. - Changes the general formatting of the PCI device output. Previous output: PCIE1: connected as Root Complex 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 03 00 10b5 8112 0604 00 02 01 10b5 8518 0604 00 02 02 10b5 8518 0604 00 08 00 1957 0040 0b20 00 07 00 10b5 8518 0604 00 09 00 10b5 8112 0604 00 07 01 10b5 8518 0604 00 07 02 10b5 8518 0604 00 06 00 10b5 8518 0604 00 02 03 10b5 8518 0604 00 01 00 10b5 8518 0604 00 PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d 00 1957 0040 0b20 00 PCIE2: Bus 0c - 0d Updated output: PCIE1: connected as Root Complex 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 03:00.0 - 10b5:8112 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 02:02.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:00.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:01.0 - 10b5:8518 - Bridge device 07:02.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 01:00.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:27 +00:00
if (vendor == 0xffff || vendor == 0x0000)
continue;
2002-11-03 00:24:07 +00:00
pci: Clean up PCI info when CONFIG_PCI_SCAN_SHOW This change does the following: - Removes the printing of the PCI interrupt line value. This is normally set to 0 by U-Boot on bootup and is rarely used during everyday operation. - Prints out the PCI function number of a device. Previously a device with multiple functions would be printed identically 2 times, which is generally confusing. For example, on an Intel 2 port gigabit Ethernet card the following was displayed: ... 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 ... - Prints a text description of each device's PCI class instead of the raw PCI class code. The textual description makes it much easier to determine what devices are installed on a PCI bus. - Changes the general formatting of the PCI device output. Previous output: PCIE1: connected as Root Complex 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 03 00 10b5 8112 0604 00 02 01 10b5 8518 0604 00 02 02 10b5 8518 0604 00 08 00 1957 0040 0b20 00 07 00 10b5 8518 0604 00 09 00 10b5 8112 0604 00 07 01 10b5 8518 0604 00 07 02 10b5 8518 0604 00 06 00 10b5 8518 0604 00 02 03 10b5 8518 0604 00 01 00 10b5 8518 0604 00 PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d 00 1957 0040 0b20 00 PCIE2: Bus 0c - 0d Updated output: PCIE1: connected as Root Complex 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 03:00.0 - 10b5:8112 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 02:02.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:00.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:01.0 - 10b5:8518 - Bridge device 07:02.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 01:00.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:27 +00:00
if (!PCI_FUNC(dev))
found_multi = header_type & 0x80;
2002-11-03 00:24:07 +00:00
debug("PCI Scan: Found Bus %d, Device %d, Function %d\n",
PCI_BUS(dev), PCI_DEV(dev), PCI_FUNC(dev));
2002-11-03 00:24:07 +00:00
pci: Clean up PCI info when CONFIG_PCI_SCAN_SHOW This change does the following: - Removes the printing of the PCI interrupt line value. This is normally set to 0 by U-Boot on bootup and is rarely used during everyday operation. - Prints out the PCI function number of a device. Previously a device with multiple functions would be printed identically 2 times, which is generally confusing. For example, on an Intel 2 port gigabit Ethernet card the following was displayed: ... 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 ... - Prints a text description of each device's PCI class instead of the raw PCI class code. The textual description makes it much easier to determine what devices are installed on a PCI bus. - Changes the general formatting of the PCI device output. Previous output: PCIE1: connected as Root Complex 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 03 00 10b5 8112 0604 00 02 01 10b5 8518 0604 00 02 02 10b5 8518 0604 00 08 00 1957 0040 0b20 00 07 00 10b5 8518 0604 00 09 00 10b5 8112 0604 00 07 01 10b5 8518 0604 00 07 02 10b5 8518 0604 00 06 00 10b5 8518 0604 00 02 03 10b5 8518 0604 00 01 00 10b5 8518 0604 00 PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d 00 1957 0040 0b20 00 PCIE2: Bus 0c - 0d Updated output: PCIE1: connected as Root Complex 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 03:00.0 - 10b5:8112 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 02:02.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:00.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:01.0 - 10b5:8518 - Bridge device 07:02.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 01:00.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:27 +00:00
pci_hose_read_config_word(hose, dev, PCI_DEVICE_ID, &device);
pci_hose_read_config_word(hose, dev, PCI_CLASS_DEVICE, &class);
2002-11-03 00:24:07 +00:00
#ifdef CONFIG_PCI_FIXUP_DEV
board_pci_fixup_dev(hose, dev, vendor, device, class);
#endif
pci: Fix ordering of devices when CONFIG_PCI_SCAN_SHOW Move the printing of PCI device information to before the PCI device is configured. This prevents the case where recursive scanning results in the deepest devices being printed first. This change also makes PCI lockups during enumeration easier to diagnose since the device that is being configured is printed out prior to configuration. Previously, it was not possible to determine which device caused the PCI lockup. Original example: PCIE1: connected as Root Complex 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 03:00.0 - 10b5:8112 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 02:02.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:00.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:01.0 - 10b5:8518 - Bridge device 07:02.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 01:00.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b Updated example: PCIE1: connected as Root Complex 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 03:00.0 - 10b5:8112 - Bridge device 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 07:00.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:01.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:02.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:28 +00:00
#ifdef CONFIG_PCI_SCAN_SHOW
pci: Use intelligent indentation for CONFIG_PCI_SCAN_SHOW When CONFIG_PCI_SCAN_SHOW is defined U-Boot prints out PCI devices as they are found during bootup, eg: PCIE1: connected as Root Complex 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 03:00.0 - 10b5:8112 - Bridge device 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 07:00.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:01.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:02.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d This information is useful, but its difficult to determine the PCI bus topology. To things clearer, we can use indention to make it more obvious how the PCI bus is organized. For the example above, the updated output with this change is: PCIE1: connected as Root Complex 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 03:00.0 - 10b5:8112 - Bridge device 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 07:00.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:01.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:02.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d In the examples above, an MPC8640 is connected to a PEX8518 PCIe switch (01:00 and 02:0x), which is connected to another PEX8518 PCIe switch (06:00 and 07:0x), which then connects to a MPC8572 processor (08:00). Also, the MPC8640's PEX8518 PCIe switch is connected to a PCI ethernet card (04:01) via a PEX8112 PCIe-to-PCI bridge (03:00). Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:29 +00:00
indent++;
/* Print leading space, including bus indentation */
printf("%*c", indent + 1, ' ');
pci: Fix ordering of devices when CONFIG_PCI_SCAN_SHOW Move the printing of PCI device information to before the PCI device is configured. This prevents the case where recursive scanning results in the deepest devices being printed first. This change also makes PCI lockups during enumeration easier to diagnose since the device that is being configured is printed out prior to configuration. Previously, it was not possible to determine which device caused the PCI lockup. Original example: PCIE1: connected as Root Complex 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 03:00.0 - 10b5:8112 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 02:02.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:00.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:01.0 - 10b5:8518 - Bridge device 07:02.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 01:00.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b Updated example: PCIE1: connected as Root Complex 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 03:00.0 - 10b5:8112 - Bridge device 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 07:00.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:01.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:02.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:28 +00:00
if (pci_print_dev(hose, dev)) {
pci: Use intelligent indentation for CONFIG_PCI_SCAN_SHOW When CONFIG_PCI_SCAN_SHOW is defined U-Boot prints out PCI devices as they are found during bootup, eg: PCIE1: connected as Root Complex 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 03:00.0 - 10b5:8112 - Bridge device 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 07:00.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:01.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:02.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d This information is useful, but its difficult to determine the PCI bus topology. To things clearer, we can use indention to make it more obvious how the PCI bus is organized. For the example above, the updated output with this change is: PCIE1: connected as Root Complex 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 03:00.0 - 10b5:8112 - Bridge device 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 07:00.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:01.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:02.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d In the examples above, an MPC8640 is connected to a PEX8518 PCIe switch (01:00 and 02:0x), which is connected to another PEX8518 PCIe switch (06:00 and 07:0x), which then connects to a MPC8572 processor (08:00). Also, the MPC8640's PEX8518 PCIe switch is connected to a PCI ethernet card (04:01) via a PEX8112 PCIe-to-PCI bridge (03:00). Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:29 +00:00
printf("%02x:%02x.%-*x - %04x:%04x - %s\n",
PCI_BUS(dev), PCI_DEV(dev), 6 - indent, PCI_FUNC(dev),
pci: Fix ordering of devices when CONFIG_PCI_SCAN_SHOW Move the printing of PCI device information to before the PCI device is configured. This prevents the case where recursive scanning results in the deepest devices being printed first. This change also makes PCI lockups during enumeration easier to diagnose since the device that is being configured is printed out prior to configuration. Previously, it was not possible to determine which device caused the PCI lockup. Original example: PCIE1: connected as Root Complex 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 03:00.0 - 10b5:8112 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 02:02.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:00.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:01.0 - 10b5:8518 - Bridge device 07:02.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 01:00.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b Updated example: PCIE1: connected as Root Complex 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 03:00.0 - 10b5:8112 - Bridge device 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 07:00.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:01.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:02.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:28 +00:00
vendor, device, pci_class_str(class >> 8));
}
#endif
#ifdef CONFIG_PCI_PNP
sub_bus = max(pciauto_config_device(hose, dev), sub_bus);
#else
pci: Clean up PCI info when CONFIG_PCI_SCAN_SHOW This change does the following: - Removes the printing of the PCI interrupt line value. This is normally set to 0 by U-Boot on bootup and is rarely used during everyday operation. - Prints out the PCI function number of a device. Previously a device with multiple functions would be printed identically 2 times, which is generally confusing. For example, on an Intel 2 port gigabit Ethernet card the following was displayed: ... 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 ... - Prints a text description of each device's PCI class instead of the raw PCI class code. The textual description makes it much easier to determine what devices are installed on a PCI bus. - Changes the general formatting of the PCI device output. Previous output: PCIE1: connected as Root Complex 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 03 00 10b5 8112 0604 00 02 01 10b5 8518 0604 00 02 02 10b5 8518 0604 00 08 00 1957 0040 0b20 00 07 00 10b5 8518 0604 00 09 00 10b5 8112 0604 00 07 01 10b5 8518 0604 00 07 02 10b5 8518 0604 00 06 00 10b5 8518 0604 00 02 03 10b5 8518 0604 00 01 00 10b5 8518 0604 00 PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d 00 1957 0040 0b20 00 PCIE2: Bus 0c - 0d Updated output: PCIE1: connected as Root Complex 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 03:00.0 - 10b5:8112 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 02:02.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:00.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:01.0 - 10b5:8518 - Bridge device 07:02.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 01:00.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:27 +00:00
cfg = pci_find_config(hose, class, vendor, device,
PCI_BUS(dev), PCI_DEV(dev), PCI_FUNC(dev));
if (cfg) {
cfg->config_device(hose, dev, cfg);
sub_bus = max(sub_bus, hose->current_busno);
}
#endif
pci: Fix ordering of devices when CONFIG_PCI_SCAN_SHOW Move the printing of PCI device information to before the PCI device is configured. This prevents the case where recursive scanning results in the deepest devices being printed first. This change also makes PCI lockups during enumeration easier to diagnose since the device that is being configured is printed out prior to configuration. Previously, it was not possible to determine which device caused the PCI lockup. Original example: PCIE1: connected as Root Complex 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 03:00.0 - 10b5:8112 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 02:02.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:00.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:01.0 - 10b5:8518 - Bridge device 07:02.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 01:00.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b Updated example: PCIE1: connected as Root Complex 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 03:00.0 - 10b5:8112 - Bridge device 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 07:00.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:01.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:02.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:28 +00:00
pci: Use intelligent indentation for CONFIG_PCI_SCAN_SHOW When CONFIG_PCI_SCAN_SHOW is defined U-Boot prints out PCI devices as they are found during bootup, eg: PCIE1: connected as Root Complex 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 03:00.0 - 10b5:8112 - Bridge device 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 07:00.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:01.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:02.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d This information is useful, but its difficult to determine the PCI bus topology. To things clearer, we can use indention to make it more obvious how the PCI bus is organized. For the example above, the updated output with this change is: PCIE1: connected as Root Complex 01:00.0 - 10b5:8518 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 03:00.0 - 10b5:8112 - Bridge device 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 02:02.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 07:00.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:01.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:02.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d In the examples above, an MPC8640 is connected to a PEX8518 PCIe switch (01:00 and 02:0x), which is connected to another PEX8518 PCIe switch (06:00 and 07:0x), which then connects to a MPC8572 processor (08:00). Also, the MPC8640's PEX8518 PCIe switch is connected to a PCI ethernet card (04:01) via a PEX8112 PCIe-to-PCI bridge (03:00). Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:29 +00:00
#ifdef CONFIG_PCI_SCAN_SHOW
indent--;
#endif
pci: Clean up PCI info when CONFIG_PCI_SCAN_SHOW This change does the following: - Removes the printing of the PCI interrupt line value. This is normally set to 0 by U-Boot on bootup and is rarely used during everyday operation. - Prints out the PCI function number of a device. Previously a device with multiple functions would be printed identically 2 times, which is generally confusing. For example, on an Intel 2 port gigabit Ethernet card the following was displayed: ... 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 ... - Prints a text description of each device's PCI class instead of the raw PCI class code. The textual description makes it much easier to determine what devices are installed on a PCI bus. - Changes the general formatting of the PCI device output. Previous output: PCIE1: connected as Root Complex 04 01 8086 1010 0200 00 04 01 8086 1010 0200 00 03 00 10b5 8112 0604 00 02 01 10b5 8518 0604 00 02 02 10b5 8518 0604 00 08 00 1957 0040 0b20 00 07 00 10b5 8518 0604 00 09 00 10b5 8112 0604 00 07 01 10b5 8518 0604 00 07 02 10b5 8518 0604 00 06 00 10b5 8518 0604 00 02 03 10b5 8518 0604 00 01 00 10b5 8518 0604 00 PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d 00 1957 0040 0b20 00 PCIE2: Bus 0c - 0d Updated output: PCIE1: connected as Root Complex 04:01.0 - 8086:1010 - Network controller 04:01.1 - 8086:1010 - Network controller 03:00.0 - 10b5:8112 - Bridge device 02:01.0 - 10b5:8518 - Bridge device 02:02.0 - 10b5:8518 - Bridge device 08:00.0 - 1957:0040 - Processor 07:00.0 - 10b5:8518 - Bridge device 09:00.0 - 10b5:8112 - Bridge device 07:01.0 - 10b5:8518 - Bridge device 07:02.0 - 10b5:8518 - Bridge device 06:00.0 - 10b5:8518 - Bridge device 02:03.0 - 10b5:8518 - Bridge device 01:00.0 - 10b5:8518 - Bridge device PCIE1: Bus 00 - 0b PCIE2: connected as Root Complex 0d:00.0 - 1957:0040 - Processor PCIE2: Bus 0c - 0d Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2010-10-29 22:59:27 +00:00
if (hose->fixup_irq)
hose->fixup_irq(hose, dev);
2002-11-03 00:24:07 +00:00
}
return sub_bus;
}
int pci_hose_scan(struct pci_controller *hose)
{
#if defined(CONFIG_PCI_BOOTDELAY)
static int pcidelay_done;
char *s;
int i;
if (!pcidelay_done) {
/* wait "pcidelay" ms (if defined)... */
s = getenv("pcidelay");
if (s) {
int val = simple_strtoul(s, NULL, 10);
for (i = 0; i < val; i++)
udelay(1000);
}
pcidelay_done = 1;
}
#endif /* CONFIG_PCI_BOOTDELAY */
/*
* Start scan at current_busno.
* PCIe will start scan at first_busno+1.
*/
/* For legacy support, ensure current >= first */
if (hose->first_busno > hose->current_busno)
hose->current_busno = hose->first_busno;
2002-11-03 00:24:07 +00:00
#ifdef CONFIG_PCI_PNP
pciauto_config_init(hose);
#endif
return pci_hose_scan_bus(hose, hose->current_busno);
2002-11-03 00:24:07 +00:00
}
void pci_init(void)
{
hose_head = NULL;
/* now call board specific pci_init()... */
pci_init_board();
}
/* Returns the address of the requested capability structure within the
* device's PCI configuration space or 0 in case the device does not
* support it.
* */
int pci_hose_find_capability(struct pci_controller *hose, pci_dev_t dev,
int cap)
{
int pos;
u8 hdr_type;
pci_hose_read_config_byte(hose, dev, PCI_HEADER_TYPE, &hdr_type);
pos = pci_hose_find_cap_start(hose, dev, hdr_type & 0x7F);
if (pos)
pos = pci_find_cap(hose, dev, pos, cap);
return pos;
}
/* Find the header pointer to the Capabilities*/
int pci_hose_find_cap_start(struct pci_controller *hose, pci_dev_t dev,
u8 hdr_type)
{
u16 status;
pci_hose_read_config_word(hose, dev, PCI_STATUS, &status);
if (!(status & PCI_STATUS_CAP_LIST))
return 0;
switch (hdr_type) {
case PCI_HEADER_TYPE_NORMAL:
case PCI_HEADER_TYPE_BRIDGE:
return PCI_CAPABILITY_LIST;
case PCI_HEADER_TYPE_CARDBUS:
return PCI_CB_CAPABILITY_LIST;
default:
return 0;
}
}
int pci_find_cap(struct pci_controller *hose, pci_dev_t dev, int pos, int cap)
{
int ttl = PCI_FIND_CAP_TTL;
u8 id;
u8 next_pos;
while (ttl--) {
pci_hose_read_config_byte(hose, dev, pos, &next_pos);
if (next_pos < CAP_START_POS)
break;
next_pos &= ~3;
pos = (int) next_pos;
pci_hose_read_config_byte(hose, dev,
pos + PCI_CAP_LIST_ID, &id);
if (id == 0xff)
break;
if (id == cap)
return pos;
pos += PCI_CAP_LIST_NEXT;
}
return 0;
}