u-boot/configs/imx8qm_mek_defconfig

111 lines
3 KiB
Text
Raw Normal View History

CONFIG_ARM=y
CONFIG_ARCH_IMX8=y
CONFIG_TEXT_BASE=0x80020000
CONFIG_SYS_MALLOC_LEN=0x2400000
CONFIG_SYS_MALLOC_F_LEN=0x8000
CONFIG_SPL_GPIO=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_NR_DRAM_BANKS=3
CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x80200000
CONFIG_ENV_SIZE=0x1000
CONFIG_ENV_OFFSET=0x400000
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="fsl-imx8qm-mek"
CONFIG_SPL_TEXT_BASE=0x100000
CONFIG_TARGET_IMX8QM_MEK=y
CONFIG_SPL_MMC=y
CONFIG_SPL_SERIAL=y
CONFIG_SPL_DRIVERS_MISC=y
CONFIG_SPL_STACK=0x13e000
CONFIG_SPL=y
CONFIG_SPL_LOAD_IMX_CONTAINER=y
CONFIG_IMX_CONTAINER_CFG="board/freescale/imx8qm_mek/uboot-container.cfg"
CONFIG_SYS_LOAD_ADDR=0x80280000
CONFIG_REMAKE_ELF=y
CONFIG_FIT=y
CONFIG_FIT_EXTERNAL_OFFSET=0x3000
CONFIG_BOOTDELAY=3
CONFIG_OF_BOARD_SETUP=y
CONFIG_OF_SYSTEM_SETUP=y
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="mmc dev ${mmcdev}; if mmc rescan; then if run loadbootscript; then run bootscript; else if test ${sec_boot} = yes; then if run loadcntr; then run mmcboot; else run netboot; fi; else if run loadimage; then run mmcboot; else run netboot; fi; fi; fi; else booti ${loadaddr} - ${fdt_addr}; fi"
CONFIG_LOG=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_MAX_SIZE=0x1f000
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
CONFIG_SPL_BSS_START_ADDR=0x128000
CONFIG_SPL_BSS_MAX_SIZE=0x1000
CONFIG_SPL_BOARD_INIT=y
arm: imx: Check header before calling spl_load_imx_container Make sure we have an IMX header before calling spl_load_imx_container, since if we don't it will fail with -ENOENT. This allows us to fall back to legacy/raw images if they are also enabled. This is a functional change, one which likely should have been in place from the start, but a functional change nonetheless. Previously, all non-IMX8 images (except FITs without FIT_FULL) would be optimized out if the only image load method enabled supported IMX8 images. With this change, support for other image types now has an effect. There are seven boards with SPL_LOAD_IMX_CONTAINER enabled: three with SPL_BOOTROM_SUPPORT: imx93_11x11_evk_ld imx93_11x11_evk imx8ulp_evk and four with SPL_MMC: deneb imx8qxp_mek giedi imx8qm_mek All of these boards also have SPL_RAW_IMAGE_SUPPORT and SPL_LEGACY_IMAGE_FORMAT enabled as well. However, none have FIT support enabled. Of the six load methods affected by this patch, only SPL_MMC and SPL_BOOTROM_SUPPORT are enabled with SPL_LOAD_IMX_CONTAINER. spl_romapi_load_image_seekable does not support legacy or raw images, so there is no growth. However, mmc_load_image_raw_sector does support loading legacy/raw images. Since these images could not have been booted before, I have disabled support for legacy/raw images on these four boards. This reduces bloat from around 800 bytes to around 200. There are no in-tree boards with SPL_LOAD_IMX_CONTAINER and AHAB_BOOT both enabled, so we do not need to worry about potentially falling back to legacy images in a secure boot scenario. Future work could include merging imx_container.h with imx8image.h, since they appear to define mostly the same structures. Signed-off-by: Sean Anderson <seanga2@gmail.com>
2023-10-14 20:47:44 +00:00
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
# CONFIG_SPL_LEGACY_IMAGE_FORMAT is not set
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
CONFIG_SPL_SYS_MALLOC=y
CONFIG_SPL_HAS_CUSTOM_MALLOC_START=y
CONFIG_SPL_CUSTOM_SYS_MALLOC_ADDR=0x120000
CONFIG_SPL_SYS_MALLOC_SIZE=0x3000
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x800
CONFIG_SPL_POWER_DOMAIN=y
CONFIG_SPL_WATCHDOG=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_CBSIZE=256
CONFIG_SYS_PBSIZE=276
CONFIG_CMD_CPU=y
# CONFIG_BOOTM_NETBSD is not set
# CONFIG_CMD_EXPORTENV is not set
# CONFIG_CMD_IMPORTENV is not set
# CONFIG_CMD_CRC32 is not set
CONFIG_CMD_CLK=y
CONFIG_CMD_DM=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_FAT=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_SYS_MMC_ENV_DEV=1
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_SPL_DM=y
CONFIG_SPL_CLK=y
CONFIG_CLK_IMX8=y
CONFIG_CPU=y
CONFIG_MXC_GPIO=y
CONFIG_DM_PCA953X=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_IMX_LPI2C=y
CONFIG_I2C_MUX=y
CONFIG_I2C_MUX_PCA954x=y
CONFIG_SUPPORT_EMMC_BOOT=y
CONFIG_FSL_USDHC=y
CONFIG_PHYLIB=y
CONFIG_PHY_ADDR_ENABLE=y
CONFIG_PHY_ATHEROS=y
CONFIG_PHY_GIGE=y
CONFIG_FEC_MXC_SHARE_MDIO=y
CONFIG_FEC_MXC_MDIO_BASE=0x5B040000
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_SPL_PINCTRL=y
CONFIG_PINCTRL_IMX8=y
CONFIG_POWER_DOMAIN=y
CONFIG_IMX8_POWER_DOMAIN=y
CONFIG_DM_REGULATOR=y
CONFIG_SPL_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_SPL_DM_REGULATOR_GPIO=y
CONFIG_DM_SERIAL=y
CONFIG_FSL_LPUART=y
CONFIG_SPL_TINY_MEMSET=y
# CONFIG_EFI_LOADER is not set