2015-07-25 17:46:26 +00:00
|
|
|
#
|
|
|
|
# Serial device configuration
|
|
|
|
#
|
|
|
|
|
|
|
|
menu "Serial drivers"
|
|
|
|
|
2017-03-17 19:34:53 +00:00
|
|
|
config BAUDRATE
|
|
|
|
int "Default baudrate"
|
|
|
|
default 115200
|
|
|
|
help
|
|
|
|
Select a default baudrate, where "default" has a driver-specific
|
|
|
|
meaning of either setting the baudrate for the early debug UART
|
|
|
|
in the SPL stage (most drivers) or for choosing a default baudrate
|
|
|
|
in the absence of an environment setting (serial_mxc.c).
|
|
|
|
|
2015-08-08 15:45:18 +00:00
|
|
|
config REQUIRE_SERIAL_CONSOLE
|
|
|
|
bool "Require a serial port for console"
|
|
|
|
# Running without a serial console is not supported by the
|
|
|
|
# non-dm serial code
|
|
|
|
depends on DM_SERIAL
|
|
|
|
default y
|
|
|
|
help
|
|
|
|
Require a serial port for the console, and panic if none is found
|
|
|
|
during serial port initialization (default y). Set this to n on
|
|
|
|
boards which have no debug serial port whatsoever.
|
|
|
|
|
2018-03-07 00:02:27 +00:00
|
|
|
config SPECIFY_CONSOLE_INDEX
|
|
|
|
bool "Specify the port number used for console"
|
|
|
|
default y if !DM_SERIAL || (SPL && !SPL_DM_SERIAL) || \
|
|
|
|
(TPL && !TPL_DM_SERIAL)
|
|
|
|
help
|
|
|
|
In various cases, we need to specify which of the UART devices that
|
|
|
|
a board or SoC has available are to be used for the console device
|
|
|
|
in U-Boot.
|
|
|
|
|
2015-12-14 04:36:58 +00:00
|
|
|
config SERIAL_PRESENT
|
|
|
|
bool "Provide a serial driver"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
default y
|
|
|
|
help
|
|
|
|
In very space-constrained devices even the full UART driver is too
|
|
|
|
large. In this case the debug UART can still be used in some cases.
|
|
|
|
This option enables the full UART in U-Boot, so if is it disabled,
|
|
|
|
the full UART driver will be omitted, thus saving space.
|
|
|
|
|
|
|
|
config SPL_SERIAL_PRESENT
|
|
|
|
bool "Provide a serial driver in SPL"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
default y
|
|
|
|
help
|
|
|
|
In very space-constrained devices even the full UART driver is too
|
|
|
|
large. In this case the debug UART can still be used in some cases.
|
|
|
|
This option enables the full UART in SPL, so if is it disabled,
|
|
|
|
the full UART driver will be omitted, thus saving space.
|
|
|
|
|
2018-10-01 18:22:20 +00:00
|
|
|
config TPL_SERIAL_PRESENT
|
|
|
|
bool "Provide a serial driver in TPL"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
default y
|
|
|
|
help
|
|
|
|
In very space-constrained devices even the full UART driver is too
|
|
|
|
large. In this case the debug UART can still be used in some cases.
|
|
|
|
This option enables the full UART in TPL, so if is it disabled,
|
|
|
|
the full UART driver will be omitted, thus saving space.
|
|
|
|
|
2018-03-07 00:02:27 +00:00
|
|
|
# Logic to allow us to use the imply keyword to set what the default port
|
|
|
|
# should be. The default is otherwise 1.
|
|
|
|
config CONS_INDEX_0
|
|
|
|
bool
|
|
|
|
|
|
|
|
config CONS_INDEX_2
|
|
|
|
bool
|
|
|
|
|
|
|
|
config CONS_INDEX_3
|
|
|
|
bool
|
|
|
|
|
|
|
|
config CONS_INDEX_4
|
|
|
|
bool
|
|
|
|
|
|
|
|
config CONS_INDEX_5
|
|
|
|
bool
|
|
|
|
|
|
|
|
config CONS_INDEX_6
|
|
|
|
bool
|
|
|
|
|
2017-04-02 10:59:11 +00:00
|
|
|
config CONS_INDEX
|
|
|
|
int "UART used for console"
|
2018-03-07 00:02:27 +00:00
|
|
|
depends on SPECIFY_CONSOLE_INDEX
|
|
|
|
range 0 6
|
|
|
|
default 0 if CONS_INDEX_0
|
|
|
|
default 2 if CONS_INDEX_2
|
|
|
|
default 3 if CONS_INDEX_3
|
|
|
|
default 4 if CONS_INDEX_4
|
|
|
|
default 5 if CONS_INDEX_5
|
|
|
|
default 6 if CONS_INDEX_6
|
2017-04-02 10:59:11 +00:00
|
|
|
default 1
|
|
|
|
help
|
2018-03-07 00:02:27 +00:00
|
|
|
Set this to match the UART number of the serial console.
|
2017-04-02 10:59:11 +00:00
|
|
|
|
2014-10-23 13:26:09 +00:00
|
|
|
config DM_SERIAL
|
|
|
|
bool "Enable Driver Model for serial drivers"
|
|
|
|
depends on DM
|
|
|
|
help
|
2015-02-06 04:41:35 +00:00
|
|
|
Enable driver model for serial. This replaces
|
|
|
|
drivers/serial/serial.c with the serial uclass, which
|
|
|
|
implements serial_putc() etc. The uclass interface is
|
|
|
|
defined in include/serial.h.
|
2014-10-23 13:26:11 +00:00
|
|
|
|
2017-08-16 15:37:16 +00:00
|
|
|
config SERIAL_RX_BUFFER
|
|
|
|
bool "Enable RX buffer for serial input"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
help
|
|
|
|
Enable RX buffer support for the serial driver. This enables
|
|
|
|
pasting longer strings, even when the RX FIFO of the UART is
|
|
|
|
not big enough (e.g. 16 bytes on the normal NS16550).
|
|
|
|
|
|
|
|
config SERIAL_RX_BUFFER_SIZE
|
|
|
|
int "RX buffer size"
|
|
|
|
depends on SERIAL_RX_BUFFER
|
|
|
|
default 256
|
|
|
|
help
|
|
|
|
The size of the RX buffer (needs to be power of 2)
|
|
|
|
|
2018-01-29 12:57:20 +00:00
|
|
|
config SERIAL_SEARCH_ALL
|
|
|
|
bool "Search for serial devices after default one failed"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
help
|
|
|
|
The serial subsystem only searches for a single serial device
|
|
|
|
that was instantiated, but does not check whether it was probed
|
|
|
|
correctly. With this option set, we make successful probing
|
|
|
|
mandatory and search for fallback serial devices if the default
|
|
|
|
device does not work.
|
|
|
|
|
|
|
|
If unsure, say N.
|
|
|
|
|
2017-04-02 15:50:32 +00:00
|
|
|
config SPL_DM_SERIAL
|
2017-06-21 04:23:10 +00:00
|
|
|
bool "Enable Driver Model for serial drivers in SPL"
|
2018-03-07 00:02:27 +00:00
|
|
|
depends on DM_SERIAL && SPL_DM
|
|
|
|
default y
|
2017-04-02 15:50:32 +00:00
|
|
|
help
|
|
|
|
Enable driver model for serial in SPL. This replaces
|
|
|
|
drivers/serial/serial.c with the serial uclass, which
|
|
|
|
implements serial_putc() etc. The uclass interface is
|
|
|
|
defined in include/serial.h.
|
|
|
|
|
|
|
|
config TPL_DM_SERIAL
|
2017-06-21 04:23:10 +00:00
|
|
|
bool "Enable Driver Model for serial drivers in TPL"
|
2017-04-02 15:50:32 +00:00
|
|
|
depends on DM_SERIAL
|
|
|
|
default y if TPL && DM_SERIAL
|
|
|
|
help
|
|
|
|
Enable driver model for serial in TPL. This replaces
|
|
|
|
drivers/serial/serial.c with the serial uclass, which
|
|
|
|
implements serial_putc() etc. The uclass interface is
|
|
|
|
defined in include/serial.h.
|
|
|
|
|
2015-01-27 01:27:07 +00:00
|
|
|
config DEBUG_UART
|
|
|
|
bool "Enable an early debug UART for debugging"
|
|
|
|
help
|
|
|
|
The debug UART is intended for use very early in U-Boot to debug
|
|
|
|
problems when an ICE or other debug mechanism is not available.
|
|
|
|
|
|
|
|
To use it you should:
|
|
|
|
- Make sure your UART supports this interface
|
|
|
|
- Enable CONFIG_DEBUG_UART
|
|
|
|
- Enable the CONFIG for your UART to tell it to provide this interface
|
|
|
|
(e.g. CONFIG_DEBUG_UART_NS16550)
|
|
|
|
- Define the required settings as needed (see below)
|
|
|
|
- Call debug_uart_init() before use
|
|
|
|
- Call debug_uart_putc() to output a character
|
|
|
|
|
|
|
|
Depending on your platform it may be possible to use this UART before
|
|
|
|
a stack is available.
|
|
|
|
|
|
|
|
If your UART does not support this interface you can probably add
|
|
|
|
support quite easily. Remember that you cannot use driver model and
|
|
|
|
it is preferred to use no stack.
|
|
|
|
|
|
|
|
You must not use this UART once driver model is working and the
|
|
|
|
serial drivers are up and running (done in serial_init()). Otherwise
|
|
|
|
the drivers may conflict and you will get strange output.
|
|
|
|
|
2015-01-27 01:27:09 +00:00
|
|
|
choice
|
|
|
|
prompt "Select which UART will provide the debug UART"
|
|
|
|
depends on DEBUG_UART
|
2015-11-19 13:48:03 +00:00
|
|
|
default DEBUG_UART_NS16550
|
2015-01-27 01:27:09 +00:00
|
|
|
|
2015-10-22 23:36:37 +00:00
|
|
|
config DEBUG_UART_ALTERA_JTAGUART
|
|
|
|
bool "Altera JTAG UART"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the altera_jtag_uart driver.
|
|
|
|
You will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver model serial is running.
|
|
|
|
|
2015-10-21 13:26:54 +00:00
|
|
|
config DEBUG_UART_ALTERA_UART
|
|
|
|
bool "Altera UART"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the altera_uart driver.
|
|
|
|
You will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver model serial is running.
|
|
|
|
|
2016-03-16 08:59:57 +00:00
|
|
|
config DEBUG_UART_AR933X
|
|
|
|
bool "QCA/Atheros ar933x"
|
|
|
|
depends on AR933X_UART
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the ar933x uart driver.
|
|
|
|
You will need to provide parameters to make this work. The
|
|
|
|
driver will be available until the real driver model serial is
|
|
|
|
running.
|
|
|
|
|
2018-05-21 13:42:07 +00:00
|
|
|
config DEBUG_ARC_SERIAL
|
|
|
|
bool "ARC UART"
|
|
|
|
depends on ARC_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the ARC UART driver.
|
|
|
|
You will need to provide parameters to make this work. The
|
|
|
|
driver will be available until the real driver model serial is
|
|
|
|
running.
|
|
|
|
|
2016-10-17 01:49:55 +00:00
|
|
|
config DEBUG_UART_ATMEL
|
|
|
|
bool "Atmel USART"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the atmel usart driver. You
|
|
|
|
will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver-model serial is running.
|
|
|
|
|
2017-04-24 22:39:16 +00:00
|
|
|
config DEBUG_UART_BCM6345
|
|
|
|
bool "BCM6345 UART"
|
|
|
|
depends on BCM6345_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART on BCM6345 SoCs. You
|
|
|
|
will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver model serial is running.
|
|
|
|
|
2015-01-27 01:27:09 +00:00
|
|
|
config DEBUG_UART_NS16550
|
|
|
|
bool "ns16550"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the ns16550 driver. You
|
|
|
|
will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver model serial is running.
|
|
|
|
|
2015-08-04 18:33:40 +00:00
|
|
|
config DEBUG_EFI_CONSOLE
|
|
|
|
bool "EFI"
|
|
|
|
depends on EFI_APP
|
|
|
|
help
|
|
|
|
Select this to enable a debug console which calls back to EFI to
|
|
|
|
output to the console. This can be useful for early debugging of
|
|
|
|
U-Boot when running on top of EFI (Extensive Firmware Interface).
|
|
|
|
This is a type of BIOS used by PCs.
|
|
|
|
|
2015-07-03 00:15:54 +00:00
|
|
|
config DEBUG_UART_S5P
|
|
|
|
bool "Samsung S5P"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the serial_s5p driver. You
|
|
|
|
will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver-model serial is running.
|
|
|
|
|
2016-05-08 06:30:16 +00:00
|
|
|
config DEBUG_UART_MESON
|
|
|
|
bool "Amlogic Meson"
|
|
|
|
depends on MESON_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the serial_meson driver. You
|
|
|
|
will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver-model serial is running.
|
|
|
|
|
2015-12-14 15:55:10 +00:00
|
|
|
config DEBUG_UART_UARTLITE
|
|
|
|
bool "Xilinx Uartlite"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the serial_uartlite driver.
|
|
|
|
You will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver-model serial is running.
|
|
|
|
|
2016-02-23 09:02:28 +00:00
|
|
|
config DEBUG_UART_ARM_DCC
|
|
|
|
bool "ARM DCC"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the ARM JTAG DCC port.
|
|
|
|
The DCC port can be used for very early debugging and doesn't require
|
|
|
|
any additional setting like address/baudrate/clock. On systems without
|
|
|
|
any serial interface this is the easiest way how to get console.
|
|
|
|
Every ARM core has own DCC port which is the part of debug interface.
|
|
|
|
This port is available at least on ARMv6, ARMv7, ARMv8 and XScale
|
|
|
|
architectures.
|
|
|
|
|
2016-05-17 14:36:00 +00:00
|
|
|
config DEBUG_MVEBU_A3700_UART
|
|
|
|
bool "Marvell Armada 3700"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the serial_mvebu driver. You
|
|
|
|
will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver-model serial is running.
|
|
|
|
|
2015-10-18 01:41:22 +00:00
|
|
|
config DEBUG_UART_ZYNQ
|
|
|
|
bool "Xilinx Zynq"
|
|
|
|
help
|
2015-12-01 13:29:34 +00:00
|
|
|
Select this to enable a debug UART using the serial_zynq driver. You
|
2015-10-18 01:41:22 +00:00
|
|
|
will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver-model serial is running.
|
|
|
|
|
2015-10-29 10:55:34 +00:00
|
|
|
config DEBUG_UART_APBUART
|
|
|
|
depends on LEON3
|
|
|
|
bool "Gaisler APBUART"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the serial_leon3 driver. You
|
|
|
|
will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver model serial is running.
|
|
|
|
|
2015-10-14 16:54:24 +00:00
|
|
|
config DEBUG_UART_PL010
|
|
|
|
bool "pl010"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the pl01x driver with the
|
|
|
|
PL010 UART type. You will need to provide parameters to make this
|
|
|
|
work. The driver will be available until the real driver model
|
|
|
|
serial is running.
|
|
|
|
|
|
|
|
config DEBUG_UART_PL011
|
|
|
|
bool "pl011"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the pl01x driver with the
|
|
|
|
PL011 UART type. You will need to provide parameters to make this
|
|
|
|
work. The driver will be available until the real driver model
|
|
|
|
serial is running.
|
|
|
|
|
2016-01-28 10:00:14 +00:00
|
|
|
config DEBUG_UART_PIC32
|
|
|
|
bool "Microchip PIC32"
|
|
|
|
depends on PIC32_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the serial_pic32 driver. You
|
|
|
|
will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver model serial is running.
|
|
|
|
|
2017-06-06 05:31:51 +00:00
|
|
|
config DEBUG_UART_MXC
|
|
|
|
bool "IMX Serial port"
|
|
|
|
depends on MXC_UART
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the serial_mxc driver. You
|
|
|
|
will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver model serial is running.
|
|
|
|
|
2018-10-01 17:55:15 +00:00
|
|
|
config DEBUG_UART_SANDBOX
|
|
|
|
bool "sandbox"
|
|
|
|
depends on SANDBOX_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable the debug UART using the sandbox driver. This
|
|
|
|
provides basic serial output from the console without needing to
|
|
|
|
start up driver model. The driver will be available until the real
|
|
|
|
driver model serial is running.
|
|
|
|
|
2018-12-15 06:05:15 +00:00
|
|
|
config DEBUG_UART_SIFIVE
|
|
|
|
bool "SiFive UART"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the serial_sifive driver. You
|
|
|
|
will need to provide parameters to make this work. The driver will
|
|
|
|
be available until the real driver-model serial is running.
|
|
|
|
|
2018-05-17 12:50:42 +00:00
|
|
|
config DEBUG_UART_STM32
|
|
|
|
bool "STMicroelectronics STM32"
|
|
|
|
depends on STM32_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the serial_stm32 driver
|
|
|
|
You will need to provide parameters to make this work.
|
|
|
|
The driver will be available until the real driver model
|
|
|
|
serial is running.
|
|
|
|
|
2016-03-18 07:41:52 +00:00
|
|
|
config DEBUG_UART_UNIPHIER
|
|
|
|
bool "UniPhier on-chip UART"
|
|
|
|
depends on ARCH_UNIPHIER
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the UniPhier on-chip UART.
|
|
|
|
You will need to provide DEBUG_UART_BASE to make this work. The
|
|
|
|
driver will be available until the real driver-model serial is
|
|
|
|
running.
|
|
|
|
|
2017-04-22 10:27:25 +00:00
|
|
|
config DEBUG_UART_OMAP
|
|
|
|
bool "OMAP uart"
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the omap ns16550 driver.
|
|
|
|
You will need to provide parameters to make this work. The driver
|
|
|
|
will be available until the real driver model serial is running.
|
|
|
|
|
2018-11-15 02:08:02 +00:00
|
|
|
config DEBUG_UART_MTK
|
|
|
|
bool "MediaTek High-speed UART"
|
|
|
|
depends on MTK_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART using the MediaTek High-speed
|
|
|
|
UART driver.
|
|
|
|
You will need to provide parameters to make this work. The
|
|
|
|
driver will be available until the real driver model serial is
|
|
|
|
running.
|
|
|
|
|
2015-01-27 01:27:09 +00:00
|
|
|
endchoice
|
|
|
|
|
2015-01-27 01:27:07 +00:00
|
|
|
config DEBUG_UART_BASE
|
|
|
|
hex "Base address of UART"
|
|
|
|
depends on DEBUG_UART
|
2018-10-01 17:55:15 +00:00
|
|
|
default 0 if DEBUG_UART_SANDBOX
|
2015-01-27 01:27:07 +00:00
|
|
|
help
|
|
|
|
This is the base address of your UART for memory-mapped UARTs.
|
|
|
|
|
|
|
|
A default should be provided by your board, but if not you will need
|
|
|
|
to use the correct value here.
|
|
|
|
|
|
|
|
config DEBUG_UART_CLOCK
|
|
|
|
int "UART input clock"
|
|
|
|
depends on DEBUG_UART
|
2018-10-01 17:55:15 +00:00
|
|
|
default 0 if DEBUG_UART_SANDBOX
|
2015-01-27 01:27:07 +00:00
|
|
|
help
|
|
|
|
The UART input clock determines the speed of the internal UART
|
|
|
|
circuitry. The baud rate is derived from this by dividing the input
|
|
|
|
clock down.
|
|
|
|
|
|
|
|
A default should be provided by your board, but if not you will need
|
|
|
|
to use the correct value here.
|
|
|
|
|
2015-02-28 05:06:25 +00:00
|
|
|
config DEBUG_UART_SHIFT
|
|
|
|
int "UART register shift"
|
|
|
|
depends on DEBUG_UART
|
|
|
|
default 0 if DEBUG_UART
|
|
|
|
help
|
|
|
|
Some UARTs (notably ns16550) support different register layouts
|
|
|
|
where the registers are spaced either as bytes, words or some other
|
|
|
|
value. Use this value to specify the shift to use, where 0=byte
|
|
|
|
registers, 2=32-bit word registers, etc.
|
|
|
|
|
2015-10-19 01:51:24 +00:00
|
|
|
config DEBUG_UART_BOARD_INIT
|
|
|
|
bool "Enable board-specific debug UART init"
|
|
|
|
depends on DEBUG_UART
|
|
|
|
help
|
|
|
|
Some boards need to set things up before the debug UART can be used.
|
|
|
|
On these boards a call to debug_uart_init() is insufficient. When
|
|
|
|
this option is enabled, the function board_debug_uart_init() will
|
|
|
|
be called when debug_uart_init() is called. You can put any code
|
|
|
|
here that is needed to set up the UART ready for use, such as set
|
|
|
|
pin multiplexing or enable clocks.
|
|
|
|
|
2015-10-19 01:51:25 +00:00
|
|
|
config DEBUG_UART_ANNOUNCE
|
|
|
|
bool "Show a message when the debug UART starts up"
|
|
|
|
depends on DEBUG_UART
|
|
|
|
help
|
|
|
|
Enable this option to show a message when the debug UART is ready
|
|
|
|
for use. You will see a message like "<debug_uart> " as soon as
|
|
|
|
U-Boot has the UART ready for use (i.e. your code calls
|
|
|
|
debug_uart_init()). This can be useful just as a check that
|
|
|
|
everything is working.
|
|
|
|
|
2015-10-14 16:54:24 +00:00
|
|
|
config DEBUG_UART_SKIP_INIT
|
|
|
|
bool "Skip UART initialization"
|
2019-01-09 19:27:09 +00:00
|
|
|
depends on DEBUG_UART
|
2015-10-14 16:54:24 +00:00
|
|
|
help
|
|
|
|
Select this if the UART you want to use for debug output is already
|
|
|
|
initialized by the time U-Boot starts its execution.
|
|
|
|
|
2019-01-09 19:35:31 +00:00
|
|
|
config DEBUG_UART_NS16550_CHECK_ENABLED
|
|
|
|
bool "Check if UART is enabled on output"
|
|
|
|
depends on DEBUG_UART
|
|
|
|
depends on DEBUG_UART_NS16550
|
|
|
|
help
|
|
|
|
Select this if puts()/putc() might be called before the debug UART
|
|
|
|
has been initialized. If this is disabled, putc() might sit in a
|
|
|
|
tight loop if it is called before debug_uart_init() has been called.
|
|
|
|
|
|
|
|
Note that this does not work for every ns16550-compatible UART and
|
|
|
|
so has to be enabled carefully or you might notice lost characters.
|
|
|
|
|
2015-10-22 23:36:37 +00:00
|
|
|
config ALTERA_JTAG_UART
|
|
|
|
bool "Altera JTAG UART support"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable an JTAG UART for Altera devices.The JTAG UART
|
|
|
|
core implements a method to communicate serial character streams
|
|
|
|
between a host PC and a Qsys system on an Altera FPGA. Please find
|
|
|
|
details on the "Embedded Peripherals IP User Guide" of Altera.
|
|
|
|
|
|
|
|
config ALTERA_JTAG_UART_BYPASS
|
|
|
|
bool "Bypass output when no connection"
|
|
|
|
depends on ALTERA_JTAG_UART
|
|
|
|
help
|
|
|
|
Bypass console output and keep going even if there is no JTAG
|
|
|
|
terminal connection with the host. The console output will resume
|
|
|
|
once the JTAG terminal is connected. Without the bypass, the console
|
|
|
|
output will wait forever until a JTAG terminal is connected. If you
|
|
|
|
not are sure, say Y.
|
|
|
|
|
2015-10-21 13:26:54 +00:00
|
|
|
config ALTERA_UART
|
|
|
|
bool "Altera UART support"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable an UART for Altera devices. Please find
|
|
|
|
details on the "Embedded Peripherals IP User Guide" of Altera.
|
|
|
|
|
2016-03-16 08:59:57 +00:00
|
|
|
config AR933X_UART
|
|
|
|
bool "QCA/Atheros ar933x UART support"
|
|
|
|
depends on DM_SERIAL && SOC_AR933X
|
|
|
|
help
|
|
|
|
Select this to enable UART support for QCA/Atheros ar933x
|
|
|
|
devices. This driver uses driver model and requires a device
|
|
|
|
tree binding to operate, please refer to the document at
|
|
|
|
doc/device-tree-bindings/serial/qca,ar9330-uart.txt.
|
|
|
|
|
2018-05-21 13:40:05 +00:00
|
|
|
config ARC_SERIAL
|
|
|
|
bool "ARC UART support"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable support for ARC UART now typically
|
|
|
|
only used in Synopsys DesignWare ARC simulators like nSIM.
|
|
|
|
|
2016-10-17 01:49:54 +00:00
|
|
|
config ATMEL_USART
|
|
|
|
bool "Atmel USART support"
|
|
|
|
help
|
|
|
|
Select this to enable USART support for Atmel SoCs. It can be
|
|
|
|
configured in the device tree, and input clock frequency can
|
|
|
|
be got from the clk node.
|
|
|
|
|
2019-04-03 13:24:19 +00:00
|
|
|
config SPL_UART_CLOCK
|
|
|
|
int "SPL fixed UART input clock"
|
|
|
|
depends on ATMEL_USART && SPL && !SPL_CLK
|
|
|
|
default 132096000 if ARCH_AT91
|
|
|
|
help
|
|
|
|
Provide a fixed clock value as input to the UART controller. This
|
|
|
|
might be needed on platforms which can't enable CONFIG_SPL_CLK
|
|
|
|
because of SPL image size restrictions.
|
|
|
|
|
2018-01-25 11:05:53 +00:00
|
|
|
config BCM283X_MU_SERIAL
|
|
|
|
bool "Support for BCM283x Mini-UART"
|
|
|
|
depends on DM_SERIAL && ARCH_BCM283X
|
|
|
|
default y
|
|
|
|
help
|
|
|
|
Select this to enable Mini-UART support on BCM283X family of SoCs.
|
|
|
|
|
2018-01-25 11:05:55 +00:00
|
|
|
config BCM283X_PL011_SERIAL
|
|
|
|
bool "Support for BCM283x PL011 UART"
|
|
|
|
depends on PL01X_SERIAL && ARCH_BCM283X
|
|
|
|
default y
|
|
|
|
help
|
|
|
|
Select this to enable an overriding PL011 driver for BCM283X SoCs
|
|
|
|
that supports automatic disable, so that it only gets used when
|
|
|
|
the UART is actually muxed.
|
|
|
|
|
2017-04-24 22:39:16 +00:00
|
|
|
config BCM6345_SERIAL
|
|
|
|
bool "Support for BCM6345 UART"
|
2018-12-01 17:42:09 +00:00
|
|
|
depends on DM_SERIAL
|
2017-04-24 22:39:16 +00:00
|
|
|
help
|
|
|
|
Select this to enable UART on BCM6345 SoCs.
|
|
|
|
|
2018-04-09 01:34:34 +00:00
|
|
|
config FSL_LINFLEXUART
|
|
|
|
bool "Freescale Linflex UART support"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable the Linflex serial module found on some
|
|
|
|
NXP SoCs like S32V234.
|
|
|
|
|
2016-01-14 03:39:00 +00:00
|
|
|
config FSL_LPUART
|
|
|
|
bool "Freescale LPUART support"
|
|
|
|
help
|
|
|
|
Select this to enable a Low Power UART for Freescale VF610 and
|
|
|
|
QorIQ Layerscape devices.
|
|
|
|
|
2016-05-17 14:36:00 +00:00
|
|
|
config MVEBU_A3700_UART
|
|
|
|
bool "UART support for Armada 3700"
|
|
|
|
default n
|
|
|
|
help
|
|
|
|
Choose this option to add support for UART driver on the Marvell
|
|
|
|
Armada 3700 SoC. The base address is configured via DT.
|
|
|
|
|
2019-03-13 20:46:49 +00:00
|
|
|
config MCFUART
|
|
|
|
bool "Freescale ColdFire UART support"
|
|
|
|
help
|
|
|
|
Choose this option to add support for UART driver on the ColdFire
|
|
|
|
SoC's family. The serial communication channel provides a full-duplex
|
|
|
|
asynchronous/synchronous receiver and transmitter deriving an
|
|
|
|
operating frequency from the internal bus clock or an external clock.
|
|
|
|
|
2016-10-08 12:30:08 +00:00
|
|
|
config MXC_UART
|
|
|
|
bool "IMX serial port support"
|
2016-11-04 10:57:02 +00:00
|
|
|
depends on MX5 || MX6
|
2016-10-08 12:30:08 +00:00
|
|
|
help
|
|
|
|
If you have a machine based on a Motorola IMX CPU you
|
|
|
|
can enable its onboard serial port by enabling this option.
|
|
|
|
|
2017-08-25 03:29:07 +00:00
|
|
|
config NULLDEV_SERIAL
|
|
|
|
bool "Null serial device"
|
|
|
|
help
|
|
|
|
Select this to enable null serial device support. A null serial
|
|
|
|
device merely acts as a placeholder for a serial device and does
|
|
|
|
nothing for all it's operation.
|
|
|
|
|
2016-01-28 10:00:14 +00:00
|
|
|
config PIC32_SERIAL
|
|
|
|
bool "Support for Microchip PIC32 on-chip UART"
|
|
|
|
depends on DM_SERIAL && MACH_PIC32
|
|
|
|
default y
|
|
|
|
help
|
|
|
|
Support for the UART found on Microchip PIC32 SoC's.
|
|
|
|
|
2015-11-19 13:48:14 +00:00
|
|
|
config SYS_NS16550
|
|
|
|
bool "NS16550 UART or compatible"
|
|
|
|
help
|
|
|
|
Support NS16550 UART or compatible. This can be enabled in the
|
|
|
|
device tree with the correct input clock frequency. If the input
|
|
|
|
clock frequency is not defined in the device tree, the macro
|
|
|
|
CONFIG_SYS_NS16550_CLK defined in a legacy board header file will
|
|
|
|
be used. It can be a constant or a function to get clock, eg,
|
|
|
|
get_serial_clock().
|
|
|
|
|
2017-02-28 12:04:10 +00:00
|
|
|
config INTEL_MID_SERIAL
|
|
|
|
bool "Intel MID platform UART support"
|
|
|
|
depends on DM_SERIAL && OF_CONTROL
|
|
|
|
depends on INTEL_MID
|
|
|
|
select SYS_NS16550
|
|
|
|
help
|
|
|
|
Select this to enable a UART for Intel MID platforms.
|
|
|
|
This uses the ns16550 driver as a library.
|
|
|
|
|
2018-01-25 11:05:50 +00:00
|
|
|
config PL010_SERIAL
|
|
|
|
bool "ARM PL010 driver"
|
|
|
|
depends on !DM_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable a UART for platforms using PL010.
|
|
|
|
|
2018-01-25 11:05:51 +00:00
|
|
|
config PL011_SERIAL
|
|
|
|
bool "ARM PL011 driver"
|
|
|
|
depends on !DM_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable a UART for platforms using PL011.
|
|
|
|
|
2018-01-25 11:05:52 +00:00
|
|
|
config PL01X_SERIAL
|
|
|
|
bool "ARM PL010 and PL011 driver"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable a UART for platforms using PL010 or PL011.
|
|
|
|
|
2016-07-04 17:58:24 +00:00
|
|
|
config ROCKCHIP_SERIAL
|
|
|
|
bool "Rockchip on-chip UART support"
|
|
|
|
depends on DM_SERIAL && SPL_OF_PLATDATA
|
|
|
|
help
|
|
|
|
Select this to enable a debug UART for Rockchip devices when using
|
2017-01-14 17:20:23 +00:00
|
|
|
CONFIG_SPL_OF_PLATDATA (i.e. a compiled-in device tree replacemenmt).
|
2016-07-04 17:58:24 +00:00
|
|
|
This uses the ns16550 driver, converting the platdata from of-platdata
|
|
|
|
to the ns16550 format.
|
|
|
|
|
2015-03-06 20:19:03 +00:00
|
|
|
config SANDBOX_SERIAL
|
|
|
|
bool "Sandbox UART support"
|
2015-08-28 11:14:21 +00:00
|
|
|
depends on SANDBOX
|
2015-03-06 20:19:03 +00:00
|
|
|
help
|
|
|
|
Select this to enable a seral UART for sandbox. This is required to
|
|
|
|
operate correctly, otherwise you will see no serial output from
|
|
|
|
sandbox. The emulated UART will display to the console and console
|
|
|
|
input will be fed into the UART. This allows you to interact with
|
|
|
|
U-Boot.
|
|
|
|
|
|
|
|
The operation of the console is controlled by the -t command-line
|
|
|
|
flag. In raw mode, U-Boot sees all characters from the terminal
|
|
|
|
before they are processed, including Ctrl-C. In cooked mode, Ctrl-C
|
|
|
|
is processed by the terminal, and terminates U-Boot. Valid options
|
|
|
|
are:
|
|
|
|
|
|
|
|
-t raw-with-sigs Raw mode, Ctrl-C will terminate U-Boot
|
|
|
|
-t raw Raw mode, Ctrl-C is processed by U-Boot
|
|
|
|
-t cooked Cooked mode, Ctrl-C terminates
|
|
|
|
|
2017-07-21 21:18:46 +00:00
|
|
|
config SCIF_CONSOLE
|
|
|
|
bool "Renesas SCIF UART support"
|
|
|
|
depends on SH || ARCH_RMOBILE
|
|
|
|
help
|
|
|
|
Select this to enable Renesas SCIF UART. To operate serial ports
|
|
|
|
on systems with RCar or SH SoCs, say Y to this option. If unsure,
|
|
|
|
say N.
|
|
|
|
|
2014-10-23 13:26:11 +00:00
|
|
|
config UNIPHIER_SERIAL
|
2015-05-29 08:30:01 +00:00
|
|
|
bool "Support for UniPhier on-chip UART"
|
2015-08-28 11:14:21 +00:00
|
|
|
depends on ARCH_UNIPHIER
|
2016-08-25 10:00:37 +00:00
|
|
|
default y
|
2014-10-23 13:26:11 +00:00
|
|
|
help
|
2015-05-29 08:30:01 +00:00
|
|
|
If you have a UniPhier based board and want to use the on-chip
|
|
|
|
serial ports, say Y to this option. If unsure, say N.
|
2015-07-27 21:47:23 +00:00
|
|
|
|
2015-12-09 11:50:05 +00:00
|
|
|
config XILINX_UARTLITE
|
|
|
|
bool "Xilinx Uarlite support"
|
2016-01-26 10:24:19 +00:00
|
|
|
depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || 4xx)
|
2015-12-09 11:50:05 +00:00
|
|
|
help
|
|
|
|
If you have a Xilinx based board and want to use the uartlite
|
|
|
|
serial ports, say Y to this option. If unsure, say N.
|
|
|
|
|
2016-05-08 06:30:16 +00:00
|
|
|
config MESON_SERIAL
|
|
|
|
bool "Support for Amlogic Meson UART"
|
|
|
|
depends on DM_SERIAL && ARCH_MESON
|
|
|
|
help
|
|
|
|
If you have an Amlogic Meson based board and want to use the on-chip
|
|
|
|
serial ports, say Y to this option. If unsure, say N.
|
|
|
|
|
2016-03-31 21:12:14 +00:00
|
|
|
config MSM_SERIAL
|
|
|
|
bool "Qualcomm on-chip UART"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
help
|
|
|
|
Support Data Mover UART used on Qualcomm Snapdragon SoCs.
|
|
|
|
It should support all Qualcomm devices with UARTDM version 1.4,
|
|
|
|
for example APQ8016 and MSM8916.
|
|
|
|
Single baudrate is supported in current implementation (115200).
|
2016-05-17 14:36:00 +00:00
|
|
|
|
2018-08-27 10:25:24 +00:00
|
|
|
config OMAP_SERIAL
|
|
|
|
bool "Support for OMAP specific UART"
|
|
|
|
depends on DM_SERIAL
|
2018-08-27 10:27:08 +00:00
|
|
|
default y if (ARCH_OMAP2PLUS || ARCH_K3)
|
2018-08-27 10:25:24 +00:00
|
|
|
select SYS_NS16550
|
|
|
|
help
|
|
|
|
If you have an TI based SoC and want to use the on-chip serial
|
|
|
|
port, say Y to this option. If unsure say N.
|
|
|
|
|
2018-06-14 18:08:38 +00:00
|
|
|
config OWL_SERIAL
|
|
|
|
bool "Actions Semi OWL UART"
|
|
|
|
depends on DM_SERIAL && ARCH_OWL
|
|
|
|
help
|
|
|
|
If you have a Actions Semi OWL based board and want to use the on-chip
|
|
|
|
serial port, say Y to this option. If unsure, say N.
|
|
|
|
Single baudrate is supported in current implementation (115200).
|
|
|
|
|
2016-11-14 20:40:25 +00:00
|
|
|
config PXA_SERIAL
|
|
|
|
bool "PXA serial port support"
|
|
|
|
help
|
|
|
|
If you have a machine based on a Marvell XScale PXA2xx CPU you
|
|
|
|
can enable its onboard serial ports by enabling this option.
|
|
|
|
|
2018-12-15 06:05:15 +00:00
|
|
|
config SIFIVE_SERIAL
|
|
|
|
bool "SiFive UART support"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
help
|
|
|
|
This driver supports the SiFive UART. If unsure say N.
|
|
|
|
|
2017-02-21 12:37:07 +00:00
|
|
|
config STI_ASC_SERIAL
|
|
|
|
bool "STMicroelectronics on-chip UART"
|
|
|
|
depends on DM_SERIAL && ARCH_STI
|
|
|
|
help
|
|
|
|
Select this to enable Asynchronous Serial Controller available
|
|
|
|
on STiH410 SoC. This is a basic implementation, it supports
|
|
|
|
following baudrate 9600, 19200, 38400, 57600 and 115200.
|
|
|
|
|
2018-01-12 08:23:49 +00:00
|
|
|
config STM32_SERIAL
|
2017-07-26 13:48:39 +00:00
|
|
|
bool "STMicroelectronics STM32 SoCs on-chip UART"
|
2018-03-12 09:46:10 +00:00
|
|
|
depends on DM_SERIAL && (STM32F4 || STM32F7 || STM32H7 || ARCH_STM32MP)
|
2017-07-26 13:48:39 +00:00
|
|
|
help
|
2018-03-12 09:46:10 +00:00
|
|
|
If you have a machine based on a STM32 F4, F7, H7 or MP1 SOC
|
|
|
|
you can enable its onboard serial ports, say Y to this option.
|
2017-09-13 16:00:05 +00:00
|
|
|
If unsure, say N.
|
2017-07-26 13:48:39 +00:00
|
|
|
|
2017-11-06 08:16:05 +00:00
|
|
|
config ZYNQ_SERIAL
|
|
|
|
bool "Cadence (Xilinx Zynq) UART support"
|
2018-04-12 15:39:46 +00:00
|
|
|
depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_ZYNQMP_R5)
|
2017-11-06 08:16:05 +00:00
|
|
|
help
|
|
|
|
This driver supports the Cadence UART. It is found e.g. in Xilinx
|
|
|
|
Zynq/ZynqMP.
|
|
|
|
|
2018-11-15 02:08:02 +00:00
|
|
|
config MTK_SERIAL
|
|
|
|
bool "MediaTek High-speed UART support"
|
|
|
|
depends on DM_SERIAL
|
|
|
|
help
|
|
|
|
Select this to enable UART support for MediaTek High-speed UART
|
|
|
|
devices. This driver uses driver model and requires a device
|
|
|
|
tree binding to operate.
|
|
|
|
The High-speed UART is compatible with the ns16550a UART and have
|
|
|
|
its own high-speed registers.
|
|
|
|
|
2017-07-06 08:33:27 +00:00
|
|
|
config MPC8XX_CONS
|
|
|
|
bool "Console driver for MPC8XX"
|
2018-03-16 16:20:41 +00:00
|
|
|
depends on MPC8xx
|
2017-07-06 08:33:27 +00:00
|
|
|
default y
|
|
|
|
|
|
|
|
choice
|
|
|
|
prompt "Console port"
|
|
|
|
default 8xx_CONS_SMC1
|
|
|
|
depends on MPC8XX_CONS
|
|
|
|
help
|
|
|
|
Depending on board, select one serial port
|
|
|
|
(CONFIG_8xx_CONS_SMC1 or CONFIG_8xx_CONS_SMC2)
|
|
|
|
|
|
|
|
config 8xx_CONS_SMC1
|
|
|
|
bool "SMC1"
|
|
|
|
|
|
|
|
config 8xx_CONS_SMC2
|
|
|
|
bool "SMC2"
|
|
|
|
|
|
|
|
endchoice
|
|
|
|
|
|
|
|
config SYS_SMC_RXBUFLEN
|
|
|
|
int "Console Rx buffer length"
|
|
|
|
depends on MPC8XX_CONS
|
|
|
|
default 1
|
|
|
|
help
|
|
|
|
With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
|
|
|
|
the maximum receive buffer length for the SMC.
|
|
|
|
This option is actual only for 8xx possible.
|
|
|
|
If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
|
|
|
|
must be defined, to setup the maximum idle timeout for
|
|
|
|
the SMC.
|
|
|
|
|
|
|
|
config SYS_MAXIDLE
|
|
|
|
int "maximum idle timeout"
|
|
|
|
depends on MPC8XX_CONS
|
|
|
|
default 0
|
|
|
|
|
|
|
|
config SYS_BRGCLK_PRESCALE
|
|
|
|
int "BRG Clock Prescale"
|
|
|
|
depends on MPC8XX_CONS
|
|
|
|
default 1
|
|
|
|
|
|
|
|
config SYS_SDSR
|
|
|
|
hex "SDSR Value"
|
|
|
|
depends on MPC8XX_CONS
|
|
|
|
default 0x83
|
|
|
|
|
|
|
|
config SYS_SDMR
|
|
|
|
hex "SDMR Value"
|
|
|
|
depends on MPC8XX_CONS
|
|
|
|
default 0
|
|
|
|
|
2015-07-25 17:46:26 +00:00
|
|
|
endmenu
|