mirror of
https://github.com/DarkFlippers/unleashed-firmware
synced 2024-12-03 01:39:17 +00:00
60 lines
No EOL
3.1 KiB
Markdown
60 lines
No EOL
3.1 KiB
Markdown
# How to use Flipper as a new SubGHz remote (not clone of original remote)
|
||
|
||
## Somfy Telis
|
||
|
||
1. Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> Somfy Telis 433Mhz
|
||
2. Open your new remote file
|
||
3. Long press (hold) the ‘Prog’ button on a remote that is already registered to the device, until the blinds move shortly up and down.
|
||
4. Press and hold the ‘Prog’ button on the flipper (Left Arrow), until the blinds move shortly up and down again.
|
||
5. Done?
|
||
|
||
## BFT Mitto
|
||
|
||
1. Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> BFT Mitto 433Mhz
|
||
2. Open your new remote file
|
||
3. You need to be in minimum 3 meters to receiver
|
||
4. Original Remote: Press hidden button on back of remote with a pin or paper clip OR press Button 1 & 2 together until remote LED lights.
|
||
5. Original Remote: Momentarily press button that opens device
|
||
6. Long press (Right Arrow) - (0xF button - Btn:F) on Flipper for like 3-5 sec
|
||
7. Done?
|
||
|
||
## Nice Flor S
|
||
|
||
- Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> Nice FloR-S 433Mhz
|
||
- Open your new remote file
|
||
|
||
### Coding using an existing remote
|
||
To enter the code of a new remote control without using your receiver, you will need
|
||
an authorised remote control (note: the first remote control must always be entered
|
||
using the receiver key). Now, with the two remote controls (your already coded
|
||
remote, and your new remote), which we shall call NEW (the one whose code we want
|
||
to enter) and OLD (the authorised one), position yourself within 3m of the gate/garage
|
||
receiver and then:
|
||
1. Press and hold the `Send` button on the flipper for at least 5 seconds and then
|
||
release.
|
||
2. Press the button on the already programmed remote 3 times slowly.
|
||
3. Press the `Send` button on the flipper slowly and then release.
|
||
|
||
### Coding directly to your receiver
|
||
Your new remote will program to your receiver as per your original remote
|
||
instructions, so please refer to your manual. But for a typical NICE FLOX2R Receiver,
|
||
the programming procedure is as follows:
|
||
1. Press the learning button on your receiver for 1-2 seconds. The LED will turn on
|
||
for 5 seconds. Within 5 seconds, complete the next step.
|
||
2. Press a `Send` button on your flipper until the LED on your receiver turns off.
|
||
3. Release the remote button and wait for 2 seconds.
|
||
4. Press the `Send` button on your flipper again. The LED on your receiver
|
||
will now flash 3 times. This indicates that your remote has been successfully
|
||
coded. If this does not happen, repeat the whole procedure from the
|
||
beginning, and try again.
|
||
5. Wait 5 seconds. Press the button on your new remote to test if it opens your
|
||
garage/gate.
|
||
|
||
|
||
#### Follow links below to find more detailed instructions!!!
|
||
|
||
#### Materials used:
|
||
- [Somfy Telis](https://pushstack.wordpress.com/somfy-rts-protocol/)
|
||
- [BFT Mitto](https://www.retroremotes.com.au/wp-content/uploads/2017/03/BFT-MITTO-2-4-19-6-17.pdf)
|
||
- [NICE FLOX2R Receiver Programming](https://apollogateopeners.com/store/pdf/apollo-flor-s-receiver-programming-guide.pdf)
|
||
- [Nice Flor S Programming](https://motepro.com.au/Instructions/Nice.pdf) |