u-boot/board/st/stm32mp1/board.c
Patrick Delaunay db4ff0df65 stpmic1: update register names
Alignment with  STPMIC1 datasheet
  s/MAIN_CONTROL_REG/MAIN_CR/g
  s/MASK_RESET_BUCK/BUCKS_MRST_CR/g
  s/MASK_RESET_LDOS/LDOS_MRST_CR/g
  s/BUCKX_CTRL_REG/BUCKX_MAIN_CR/g
  s/VREF_CTRL_REG/REFDDR_MAIN_CR/g
  s/LDOX_CTRL_REG/LDOX_MAIN_CR/g
  s/USB_CTRL_REG/BST_SW_CR/g
  s/STPMIC1_NVM_USER_STATUS_REG/STPMIC1_NVM_SR/g
  s/STPMIC1_NVM_USER_CONTROL_REG/STPMIC1_NVM_CR/g
and update all the associated defines.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12 16:09:13 +02:00

102 lines
2.2 KiB
C

// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
/*
* Copyright (C) 2018, STMicroelectronics - All Rights Reserved
*/
#include <common.h>
#include <dm.h>
#include <asm/io.h>
#include <asm/arch/ddr.h>
#include <power/pmic.h>
#include <power/stpmic1.h>
#ifdef CONFIG_DEBUG_UART_BOARD_INIT
void board_debug_uart_init(void)
{
#if (CONFIG_DEBUG_UART_BASE == STM32_UART4_BASE)
#define RCC_MP_APB1ENSETR (STM32_RCC_BASE + 0x0A00)
#define RCC_MP_AHB4ENSETR (STM32_RCC_BASE + 0x0A28)
/* UART4 clock enable */
setbits_le32(RCC_MP_APB1ENSETR, BIT(16));
#define GPIOG_BASE 0x50008000
/* GPIOG clock enable */
writel(BIT(6), RCC_MP_AHB4ENSETR);
/* GPIO configuration for EVAL board
* => Uart4 TX = G11
*/
writel(0xffbfffff, GPIOG_BASE + 0x00);
writel(0x00006000, GPIOG_BASE + 0x24);
#else
#error("CONFIG_DEBUG_UART_BASE: not supported value")
#endif
}
#endif
#ifdef CONFIG_PMIC_STPMIC1
int board_ddr_power_init(void)
{
struct udevice *dev;
int ret;
ret = uclass_get_device_by_driver(UCLASS_PMIC,
DM_GET_DRIVER(pmic_stpmic1), &dev);
if (ret)
/* No PMIC on board */
return 0;
/* VTT = Set LDO3 to sync mode */
ret = pmic_reg_read(dev, STPMIC1_LDOX_MAIN_CR(STPMIC1_LDO3));
if (ret < 0)
return ret;
ret &= ~STPMIC1_LDO3_MODE;
ret &= ~STPMIC1_LDO12356_VOUT_MASK;
ret |= STPMIC1_LDO_VOUT(STPMIC1_LDO3_DDR_SEL);
ret = pmic_reg_write(dev, STPMIC1_LDOX_MAIN_CR(STPMIC1_LDO3),
ret);
if (ret < 0)
return ret;
/* VDD_DDR = Set BUCK2 to 1.35V */
ret = pmic_clrsetbits(dev,
STPMIC1_BUCKX_MAIN_CR(STPMIC1_BUCK2),
STPMIC1_BUCK_VOUT_MASK,
STPMIC1_BUCK2_1350000V);
if (ret < 0)
return ret;
/* Enable VDD_DDR = BUCK2 */
ret = pmic_clrsetbits(dev,
STPMIC1_BUCKX_MAIN_CR(STPMIC1_BUCK2),
STPMIC1_BUCK_ENA, STPMIC1_BUCK_ENA);
if (ret < 0)
return ret;
mdelay(STPMIC1_DEFAULT_START_UP_DELAY_MS);
/* Enable VREF */
ret = pmic_clrsetbits(dev, STPMIC1_REFDDR_MAIN_CR,
STPMIC1_VREF_ENA, STPMIC1_VREF_ENA);
if (ret < 0)
return ret;
mdelay(STPMIC1_DEFAULT_START_UP_DELAY_MS);
/* Enable LDO3 */
ret = pmic_clrsetbits(dev,
STPMIC1_LDOX_MAIN_CR(STPMIC1_LDO3),
STPMIC1_LDO_ENA, STPMIC1_LDO_ENA);
if (ret < 0)
return ret;
mdelay(STPMIC1_DEFAULT_START_UP_DELAY_MS);
return 0;
}
#endif