mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-20 03:38:43 +00:00
c59e1b4d07
Specifics: 1) 36-bit only 2) Booting from NOR flash only 3) Environment stored in NOR flash only 4) No SPI support 5) No DIU support Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
106 lines
2.9 KiB
C
106 lines
2.9 KiB
C
/*
|
|
* Copyright 2010 Freescale Semiconductor, Inc.
|
|
* Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
|
|
* Timur Tabi <timur@freescale.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License as published by the Free
|
|
* Software Foundation; either version 2 of the License, or (at your option)
|
|
* any later version.
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
|
|
#include <asm/fsl_ddr_sdram.h>
|
|
#include <asm/fsl_ddr_dimm_params.h>
|
|
|
|
unsigned int fsl_ddr_get_mem_data_rate(void)
|
|
{
|
|
return get_ddr_freq(0);
|
|
}
|
|
|
|
void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd, unsigned int ctrl_num)
|
|
{
|
|
int ret;
|
|
|
|
/*
|
|
* The P1022 has only one DDR controller, and the board has only one
|
|
* DIMM slot.
|
|
*/
|
|
ret = i2c_read(SPD_EEPROM_ADDRESS1, 0, 1, (u8 *)ctrl_dimms_spd,
|
|
sizeof(ddr3_spd_eeprom_t));
|
|
if (ret) {
|
|
debug("DDR: failed to read SPD from address %u\n",
|
|
SPD_EEPROM_ADDRESS1);
|
|
memset(ctrl_dimms_spd, 0, sizeof(ddr3_spd_eeprom_t));
|
|
}
|
|
}
|
|
|
|
typedef struct {
|
|
u32 datarate_mhz_low;
|
|
u32 datarate_mhz_high;
|
|
u32 n_ranks;
|
|
u32 clk_adjust; /* Range: 0-8 */
|
|
u32 cpo; /* Range: 2-31 */
|
|
u32 write_data_delay; /* Range: 0-6 */
|
|
u32 force_2T;
|
|
} board_specific_parameters_t;
|
|
|
|
static const board_specific_parameters_t bsp[] = {
|
|
/*
|
|
* lo| hi| num| clk| cpo|wrdata|2T
|
|
* mhz| mhz|ranks|adjst| | delay|
|
|
*/
|
|
{ 0, 333, 1, 5, 31, 3, 0},
|
|
{334, 400, 1, 5, 31, 3, 0},
|
|
{401, 549, 1, 5, 31, 3, 0},
|
|
{550, 680, 1, 5, 31, 5, 0},
|
|
{681, 850, 1, 5, 31, 5, 0},
|
|
{ 0, 333, 2, 5, 31, 3, 0},
|
|
{334, 400, 2, 5, 31, 3, 0},
|
|
{401, 549, 2, 5, 31, 3, 0},
|
|
{550, 680, 2, 5, 31, 5, 0},
|
|
{681, 850, 2, 5, 31, 5, 0},
|
|
};
|
|
|
|
void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm,
|
|
unsigned int ctrl_num)
|
|
{
|
|
unsigned long ddr_freq;
|
|
unsigned int i;
|
|
|
|
/* set odt_rd_cfg and odt_wr_cfg. */
|
|
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
|
|
popts->cs_local_opts[i].odt_rd_cfg = 0;
|
|
popts->cs_local_opts[i].odt_wr_cfg = 1;
|
|
}
|
|
|
|
/*
|
|
* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
|
|
* freqency and n_banks specified in board_specific_parameters table.
|
|
*/
|
|
ddr_freq = get_ddr_freq(0) / 1000000;
|
|
for (i = 0; i < ARRAY_SIZE(bsp); i++) {
|
|
if (ddr_freq >= bsp[i].datarate_mhz_low &&
|
|
ddr_freq <= bsp[i].datarate_mhz_high &&
|
|
pdimm->n_ranks == bsp[i].n_ranks) {
|
|
popts->clk_adjust = bsp[i].clk_adjust;
|
|
popts->cpo_override = bsp[i].cpo;
|
|
popts->write_data_delay = bsp[i].write_data_delay;
|
|
popts->twoT_en = bsp[i].force_2T;
|
|
break;
|
|
}
|
|
}
|
|
|
|
popts->half_strength_driver_enable = 1;
|
|
|
|
/* Per AN4039, enable ZQ calibration. */
|
|
popts->zq_en = 1;
|
|
|
|
/*
|
|
* For wake-up on ARP, we need auto self refresh enabled
|
|
*/
|
|
popts->auto_self_refresh_en = 1;
|
|
popts->sr_it = 0xb;
|
|
}
|