mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-17 10:18:38 +00:00
9774462e34
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and stemmy, disable ATAG support. A large number of platforms had enabled support but never supported a kernel so old as to require it. Further, some platforms are old enough to support both, but are well supported by devicetree booting, and have been for a number of years. This is because some of the ATAGs related functions have been re-used to provide the same kind of information, but for devicetree or just generally to inform the user. When needed still, rename these functions to get_board_revision() instead, to avoid conflicts. In other cases, these functions were simply unused, so drop them. Cc: Andre Przywara <andre.przywara@arm.com> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Phil Sutter <phil@nwl.cc> Cc: Stefan Bosch <stefan_b@posteo.net> Signed-off-by: Tom Rini <trini@konsulko.com>
95 lines
2.3 KiB
C
95 lines
2.3 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* (C) Copyright 2007-2008
|
|
* Stelian Pop <stelian@popies.net>
|
|
* Lead Tech Design <www.leadtechdesign.com>
|
|
*
|
|
* (C) Copyright 2009-2015
|
|
* Daniel Gorsulowski <daniel.gorsulowski@esd.eu>
|
|
* esd electronic system design gmbh <www.esd.eu>
|
|
*
|
|
* Configuation settings for the esd MEESC board.
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* SoC must be defined first, before hardware.h is included.
|
|
* In this case SoC is defined in boards.cfg.
|
|
*/
|
|
#include <asm/hardware.h>
|
|
|
|
/*
|
|
* Warning: changing CONFIG_SYS_TEXT_BASE requires
|
|
* adapting the initial boot program.
|
|
* Since the linker has to swallow that define, we must use a pure
|
|
* hex number here!
|
|
*/
|
|
|
|
/* ARM asynchronous clock */
|
|
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* 32.768 kHz crystal */
|
|
#define CONFIG_SYS_AT91_MAIN_CLOCK 16000000/* 16.0 MHz crystal */
|
|
|
|
/* Misc CPU related */
|
|
|
|
/*
|
|
* Hardware drivers
|
|
*/
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_BOOTFILESIZE
|
|
|
|
/*
|
|
* SDRAM: 1 bank, min 32, max 128 MB
|
|
* Initialized before u-boot gets started.
|
|
*/
|
|
#define PHYS_SDRAM ATMEL_BASE_CS1 /* 0x20000000 */
|
|
#define PHYS_SDRAM_SIZE 0x02000000 /* 32 MByte */
|
|
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
|
|
#define CONFIG_SYS_SDRAM_SIZE PHYS_SDRAM_SIZE
|
|
|
|
/*
|
|
* Initial stack pointer: 4k - GENERATED_GBL_DATA_SIZE in internal SRAM,
|
|
* leaving the correct space for initial global data structure above
|
|
* that address while providing maximum stack area below.
|
|
*/
|
|
#define CONFIG_SYS_INIT_SP_ADDR \
|
|
(ATMEL_BASE_SRAM0 + 16 * 1024 - GENERATED_GBL_DATA_SIZE)
|
|
|
|
/* NAND flash */
|
|
#ifdef CONFIG_CMD_NAND
|
|
# define CONFIG_SYS_MAX_NAND_DEVICE 1
|
|
# define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3 /* 0x40000000 */
|
|
# define CONFIG_SYS_NAND_DBW_8
|
|
# define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
|
|
# define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
|
|
# define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15)
|
|
# define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PA(22)
|
|
#endif
|
|
|
|
/* Ethernet */
|
|
#define CONFIG_MACB
|
|
#define CONFIG_RMII
|
|
#define CONFIG_NET_RETRY_COUNT 20
|
|
#undef CONFIG_RESET_PHY_R
|
|
|
|
/* hw-controller addresses */
|
|
#define CONFIG_ET1100_BASE 0x70000000
|
|
|
|
#ifdef CONFIG_SYS_USE_DATAFLASH
|
|
|
|
/* bootstrap + u-boot + env in dataflash on CS0 */
|
|
|
|
#elif CONFIG_SYS_USE_NANDFLASH
|
|
|
|
/* bootstrap + u-boot + env + linux in nandflash */
|
|
|
|
#endif
|
|
|
|
#define CONFIG_SYS_CBSIZE 512
|
|
|
|
#endif
|