u-boot/arch/arm/mach-kirkwood/include/mach/config.h
Trevor Woerner a0aba8a2eb CONFIG_SYS_[DI]CACHE_OFF: convert to Kconfig
CONFIG_SYS_[DI]CACHE_OFF had been partially converted to Kconfig
parameters; only for the ARC architecture. This patch turns these two
parameters into Kconfig items everywhere else they are found.

All of the include/configs/* and defconfig changes in this patch are
for arm machines only. The Kconfig changes for arc, nds32, riscv,
and xtensa have been included since these symbols are found in code
under arch/{arc,nds32,riscv,xtensa}, however, no currently-defined
include/configs/* or defconfigs for these architectures exist which
include these symbols.

These results have been confirmed with tools/moveconfig.py.

Acked-by: Alexey Brodkin <abrodkin@snopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Re-migrate for a few more boards]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-18 08:15:34 -04:00

115 lines
3.2 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2011
* Marvell Semiconductor <www.marvell.com>
* Written-by: Lei Wen <leiwen@marvell.com>
*/
/*
* This file should be included in board config header file.
*
* It supports common definitions for Kirkwood platform
*/
#ifndef _KW_CONFIG_H
#define _KW_CONFIG_H
#if defined (CONFIG_KW88F6281)
#include <asm/arch/kw88f6281.h>
#elif defined (CONFIG_KW88F6192)
#include <asm/arch/kw88f6192.h>
#else
#error "SOC Name not defined"
#endif /* CONFIG_KW88F6281 */
#include <asm/arch/soc.h>
#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */
/*
* By default kwbimage.cfg from board specific folder is used
* If for some board, different configuration file need to be used,
* CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
*/
#ifndef CONFIG_SYS_KWD_CONFIG
#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
#endif /* CONFIG_SYS_KWD_CONFIG */
/* Kirkwood has 2k of Security SRAM, use it for SP */
#define CONFIG_SYS_INIT_SP_ADDR 0xC8012000
#define CONFIG_I2C_MVTWSI_BASE0 KW_TWSI_BASE
#define MV_UART_CONSOLE_BASE KW_UART0_BASE
#define MV_SATA_BASE KW_SATA_BASE
#define MV_SATA_PORT0_OFFSET KW_SATA_PORT0_OFFSET
#define MV_SATA_PORT1_OFFSET KW_SATA_PORT1_OFFSET
/*
* NAND configuration
*/
#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_KIRKWOOD
#define CONFIG_SYS_NAND_BASE 0xD8000000 /* MV_DEFADR_NANDF */
#define NAND_ALLOW_ERASE_ALL 1
#endif
/*
* Ethernet Driver configuration
*/
#ifdef CONFIG_CMD_NET
#define CONFIG_NETCONSOLE /* include NetConsole support */
#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
#endif /* CONFIG_CMD_NET */
/*
* USB/EHCI
*/
#ifdef CONFIG_CMD_USB
#define CONFIG_EHCI_IS_TDI
#endif /* CONFIG_CMD_USB */
/*
* IDE Support on SATA ports
*/
#ifdef CONFIG_IDE
#define __io
#define CONFIG_IDE_PREINIT
#define CONFIG_MVSATA_IDE_USE_PORT1
/* Needs byte-swapping for ATA data register */
#define CONFIG_IDE_SWAP_IO
/* Data, registers and alternate blocks are at the same offset */
#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100)
#define CONFIG_SYS_ATA_REG_OFFSET (0x0100)
#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100)
/* Each 8-bit ATA register is aligned to a 4-bytes address */
#define CONFIG_SYS_ATA_STRIDE 4
/* Controller supports 48-bits LBA addressing */
#define CONFIG_LBA48
/* CONFIG_IDE requires some #defines for ATA registers */
#define CONFIG_SYS_IDE_MAXBUS 2
#define CONFIG_SYS_IDE_MAXDEVICE 2
/* ATA registers base is at SATA controller base */
#define CONFIG_SYS_ATA_BASE_ADDR MV_SATA_BASE
#endif /* CONFIG_IDE */
/*
* I2C related stuff
*/
#if defined(CONFIG_CMD_I2C) && !defined(CONFIG_DM_I2C)
#ifndef CONFIG_SYS_I2C_SOFT
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
#endif
#define CONFIG_SYS_I2C_SLAVE 0x0
#define CONFIG_SYS_I2C_SPEED 100000
#endif
/* Use common timer */
#define CONFIG_SYS_TIMER_COUNTS_DOWN
#define CONFIG_SYS_TIMER_COUNTER (MVEBU_TIMER_BASE + 0x14)
#define CONFIG_SYS_TIMER_RATE CONFIG_SYS_TCLK
#endif /* _KW_CONFIG_H */