u-boot/include/configs/pg-wcom-expu1.h
Aleksandar Gerasimovski a7fd6fa1c2 board/km: add support for expu1 design based on nxp
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.

The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.

Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-06-17 11:46:11 +05:30

53 lines
1.4 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2020 Hitachi ABB Power Grids
*/
#ifndef __CONFIG_PG_WCOM_EXPU1_H
#define __CONFIG_PG_WCOM_EXPU1_H
#define WCOM_EXPU1
#define CONFIG_HOSTNAME "EXPU1"
#define CONFIG_KM_UBI_PARTITION_NAME_BOOT "ubi0"
#define CONFIG_KM_UBI_PARTITION_NAME_APP "ubi1"
/* CLIPS FPGA Definitions */
#define CONFIG_SYS_CSPR3_EXT (0x00)
#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(CONFIG_SYS_CLIPS_BASE) | \
CSPR_PORT_SIZE_8 | \
CSPR_MSEL_GPCM | \
CSPR_V)
#define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024)
#define CONFIG_SYS_CSOR3 (CSOR_GPCM_ADM_SHIFT(0x4) | \
CSOR_GPCM_TRHZ_40)
#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x6) | \
FTIM0_GPCM_TEADC(0x7) | \
FTIM0_GPCM_TEAHC(0x2))
#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x2) | \
FTIM1_GPCM_TRAD(0x12))
#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x3) | \
FTIM2_GPCM_TCH(0x1) | \
FTIM2_GPCM_TWP(0x12))
#define CONFIG_SYS_CS3_FTIM3 0x04000000
/* PRST */
#define WCOM_CLIPS_RST 0
#define WCOM_QSFP_RST 1
#define WCOM_PHY_RST 2
#define WCOM_TMG_RST 3
#define KM_DBG_ETH_RST 15
/* QRIO GPIOs used for deblocking */
#define KM_I2C_DEBLOCK_PORT QRIO_GPIO_A
#define KM_I2C_DEBLOCK_SCL 20
#define KM_I2C_DEBLOCK_SDA 21
/* ZL30343 on SPI */
#define WCOM_ZL30343_CFG_ADDR 0xe8070000
#define WCOM_ZL30343_SPI_BUS 0
#define WCOM_ZL30343_CS 0
#include "km/pg-wcom-ls102xa.h"
#endif /* __CONFIG_PG_WCOM_EXPU1_H */