u-boot/arch/arm/mach-sunxi
Icenowy Zheng 3cfecee49c sunxi: set the default CPUx frequency of H5 to 816MHz
Some H5 boards are designed to start at 1.1V CPUx voltage (e.g. Nano Pi
NEO2), which may not work properly at 1008MHz if the chip's quality is
not so good.

Lower the default CPUx frequency of H5 to 816MHz.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-12-02 21:55:25 +05:30
..
dram_timings sunxi: add LPDDR3 timing from stock boot0 2017-06-08 22:37:55 +05:30
board.c arm: sunxi: Move spl_boot_device in a separate function 2017-10-03 19:12:06 +02:00
clock.c sunxi: add gtbus-initialisation for sun9i 2016-10-30 11:38:04 +01:00
clock_sun4i.c sunxi: Move cpu independent code to mach directory 2016-04-01 09:52:28 +02:00
clock_sun6i.c sunxi: switch PRCM to non-secure on H3/H5 SoCs 2017-08-11 15:49:39 +05:30
clock_sun8i_a83t.c sunxi: Move cpu independent code to mach directory 2016-04-01 09:52:28 +02:00
clock_sun9i.c sunxi: add initial clock setup for sun9i for SPL 2016-10-30 11:38:04 +01:00
cpu_info.c sunxi: add basic V3s support 2017-04-21 09:23:17 +02:00
dram_helpers.c ARM: Rework and correct barrier definitions 2016-08-05 07:23:57 -04:00
dram_sun4i.c sunxi: Move cpu independent code to mach directory 2016-04-01 09:52:28 +02:00
dram_sun6i.c sunxi: Move cpu independent code to mach directory 2016-04-01 09:52:28 +02:00
dram_sun8i_a23.c sunxi: Move cpu independent code to mach directory 2016-04-01 09:52:28 +02:00
dram_sun8i_a33.c sunxi: Move cpu independent code to mach directory 2016-04-01 09:52:28 +02:00
dram_sun8i_a83t.c sunxi: Move cpu independent code to mach directory 2016-04-01 09:52:28 +02:00
dram_sun9i.c sunxi: DRAM initialisation for sun9i 2016-10-30 11:38:04 +01:00
dram_sunxi_dw.c sunxi: add LPDDR3 DRAM type support for DesignWare-like DRAM controller 2017-06-08 22:37:55 +05:30
gtbus_sun9i.c sunxi: add gtbus-initialisation for sun9i 2016-10-30 11:38:04 +01:00
Kconfig sunxi: set the default CPUx frequency of H5 to 816MHz 2017-12-02 21:55:25 +05:30
Makefile sunxi: Add selective DRAM type and timing 2017-06-08 22:37:55 +05:30
p2wi.c sunxi: Move cpu independent code to mach directory 2016-04-01 09:52:28 +02:00
pinmux.c sunxi: Move cpu independent code to mach directory 2016-04-01 09:52:28 +02:00
pmic_bus.c sunxi: Enable AXP221s in I2C mode with the R40 SoC 2017-04-20 13:30:00 +02:00
prcm.c sunxi: Move cpu independent code to mach directory 2016-04-01 09:52:28 +02:00
rmr_switch.S sunxi: A64: do an RMR switch if started in AArch32 mode 2017-01-04 16:37:42 +01:00
rsb.c sunxi: Move cpu independent code to mach directory 2016-04-01 09:52:28 +02:00
usb_phy.c sunxi: usb_phy: invert the USB phy_ctl condition 2017-10-03 19:12:06 +02:00