u-boot/include/configs/presidio_asic.h
Tom Rini 82cd1e3da0 Convert CONFIG_LAST_STAGE_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_LAST_STAGE_INIT

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-12 14:18:17 -05:00

82 lines
2.4 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2020 Cortina Access Inc.
*
* Configuration for Cortina-Access Presidio board
*/
#ifndef __PRESIDIO_ASIC_H
#define __PRESIDIO_ASIC_H
#define CONFIG_REMAKE_ELF
#define CONFIG_SUPPORT_RAW_INITRD
#define CONFIG_SYS_INIT_SP_ADDR 0x00100000
#define CONFIG_SYS_BOOTM_LEN 0x00c00000
/* Generic Timer Definitions */
#define COUNTER_FREQUENCY 25000000
#define CONFIG_SYS_TIMER_RATE COUNTER_FREQUENCY
#define CONFIG_SYS_TIMER_COUNTER 0xf4321008
/* note: arch/arm/cpu/armv8/start.S which references GICD_BASE/GICC_BASE
* does not yet support DT. Thus define it here.
*/
#define GICD_BASE 0xf7011000
#define GICC_BASE 0xf7012000
#define CONFIG_SYS_TIMER_BASE 0xf4321000
/* Use external clock source */
#define PRESIDIO_APB_CLK 125000000
#define CORTINA_PER_IO_FREQ PRESIDIO_APB_CLK
/* Cortina Serial Configuration */
#define CORTINA_UART_CLOCK (PRESIDIO_APB_CLK)
#define CORTINA_SERIAL_PORTS {(void *)CONFIG_SYS_SERIAL0, \
(void *)CONFIG_SYS_SERIAL1}
#define CONFIG_SYS_SERIAL0 PER_UART0_CFG
#define CONFIG_SYS_SERIAL1 PER_UART1_CFG
/* BOOTP options */
#define CONFIG_BOOTP_BOOTFILESIZE
/* SDRAM Bank #1 */
#define DDR_BASE 0x00000000
#define PHYS_SDRAM_1 DDR_BASE
#define PHYS_SDRAM_1_SIZE 0x80000000 /* 2GB */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
/* Console I/O Buffer Size */
#define CONFIG_SYS_CBSIZE 256
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define KSEG1_ATU_XLAT(x) (x)
/* HW REG ADDR */
#define NI_READ_POLL_COUNT 1000
#define CA_NI_MDIO_REG_BASE 0xF4338
#define NI_HV_GLB_MAC_ADDR_CFG0_OFFSET 0x010
#define NI_HV_GLB_MAC_ADDR_CFG1_OFFSET 0x014
#define NI_HV_PT_BASE 0x400
#define NI_HV_XRAM_BASE 0x820
#define GLOBAL_BLOCK_RESET_OFFSET 0x04
#define GLOBAL_GLOBAL_CONFIG_OFFSET 0x20
#define GLOBAL_IO_DRIVE_CONTROL_OFFSET 0x4c
/* max command args */
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_EXTRA_ENV_SETTINGS "silent=y\0"
/* nand driver parameters */
#ifdef CONFIG_TARGET_PRESIDIO_ASIC
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
#endif
#endif /* __PRESIDIO_ASIC_H */