u-boot/include/configs/exynos5-common.h
Tom Rini 308520b8f2 global: Remove unused CONFIG symbols
This removes the following unreferenced CONFIG symbols:
   CONFIG_FDTADDR
   CONFIG_FDTFILE
   CONFIG_FLASH_SECTOR_SIZE
   CONFIG_FSL_CPLD
   CONFIG_HDMI_ENCODER_I2C_ADDR
   CONFIG_I2C_MVTWSI
   CONFIG_I2C_RTC_ADDR
   CONFIG_IRAM_END
   CONFIG_IRAM_SIZE
   CONFIG_KSNET_MDIO_PHY_CONFIG_ENABLE
   CONFIG_L1_INIT_RAM
   CONFIG_MACB_SEARCH_PHY
   CONFIG_MIU_2BIT_21_7_INTERLEAVED
   CONFIG_MTD_NAND_VERIFY_WRITE
   CONFIG_MVGBE_PORTS
   CONFIG_NETDEV
   CONFIG_NUM_DSP_CPUS
   CONFIG_PHY_BASE_ADR
   CONFIG_PHY_INTERFACE_MODE
   CONFIG_PSRAM_SCFG
   CONFIG_RAMBOOT_SPIFLASH
   CONFIG_RAMBOOT_TEXT_BASE
   CONFIG_RD_LVL
   CONFIG_ROCKCHIP_SDHCI_MAX_FREQ
   CONFIG_SETUP_INITRD_TAG
   CONFIG_SH_QSPI_BASE
   CONFIG_SMDK5420
   CONFIG_SOCRATES
   CONFIG_SPI_ADDR
   CONFIG_SPI_FLASH_QUAD
   CONFIG_SPI_FLASH_SIZE
   CONFIG_SPI_HALF_DUPLEX
   CONFIG_SPI_N25Q256A_RESET
   CONFIG_TEGRA_SLINK_CTRLS
   CONFIG_TPM_TIS_BASE_ADDRESS
   CONFIG_UBOOT_SECTOR_COUNT
   CONFIG_UBOOT_SECTOR_START
   CONFIG_VAR_SIZE_SPL
   CONFIG_VERY_BIG_RAM

And also:
   BL1_SIZE
   PHY_NO
   RESERVE_BLOCK_SIZE

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-12-22 10:31:48 -05:00

100 lines
2.6 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2013 Samsung Electronics
*
* Configuration settings for the SAMSUNG EXYNOS5 board.
*/
#ifndef __CONFIG_EXYNOS5_COMMON_H
#define __CONFIG_EXYNOS5_COMMON_H
#include "exynos-common.h"
/* Power Down Modes */
#define S5P_CHECK_SLEEP 0x00000BAD
#define S5P_CHECK_DIDLE 0xBAD00000
#define S5P_CHECK_LPA 0xABAD0000
/* Offset for inform registers */
#define INFORM0_OFFSET 0x800
#define INFORM1_OFFSET 0x804
#define INFORM2_OFFSET 0x808
#define INFORM3_OFFSET 0x80c
/* select serial console configuration */
#define EXYNOS5_DEFAULT_UART_OFFSET 0x010000
/* MMC SPL */
#define COPY_BL2_FNPTR_ADDR 0x02020030
#define PHYS_SDRAM_1 CFG_SYS_SDRAM_BASE
#define PHYS_SDRAM_1_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_2 (CFG_SYS_SDRAM_BASE + SDRAM_BANK_SIZE)
#define PHYS_SDRAM_2_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_3 (CFG_SYS_SDRAM_BASE + (2 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_3_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_4 (CFG_SYS_SDRAM_BASE + (3 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_4_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_5 (CFG_SYS_SDRAM_BASE + (4 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_5_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_6 (CFG_SYS_SDRAM_BASE + (5 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_6_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_7 (CFG_SYS_SDRAM_BASE + (6 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_7_SIZE SDRAM_BANK_SIZE
#define PHYS_SDRAM_8 (CFG_SYS_SDRAM_BASE + (7 * SDRAM_BANK_SIZE))
#define PHYS_SDRAM_8_SIZE SDRAM_BANK_SIZE
/* SPI */
/* Ethernet Controllor Driver */
#ifdef CONFIG_CMD_NET
#define CONFIG_ENV_SROM_BANK 1
#endif /*CONFIG_CMD_NET*/
/* Enable Time Command */
/* USB */
/* USB boot mode */
#define EXYNOS_COPY_USB_FNPTR_ADDR 0x02020070
#define EXYNOS_USB_SECONDARY_BOOT 0xfeed0002
#define EXYNOS_IRAM_SECONDARY_BASE 0x02020018
#define BOOT_TARGET_DEVICES(func) \
func(MMC, mmc, 2) \
func(MMC, mmc, 1) \
func(MMC, mmc, 0) \
func(PXE, pxe, na) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
#ifndef MEM_LAYOUT_ENV_SETTINGS
/* 2GB RAM, bootm size of 256M, load scripts after that */
#define MEM_LAYOUT_ENV_SETTINGS \
"bootm_size=0x10000000\0" \
"kernel_addr_r=0x42000000\0" \
"fdt_addr_r=0x43000000\0" \
"ramdisk_addr_r=0x43300000\0" \
"scriptaddr=0x50000000\0" \
"pxefile_addr_r=0x51000000\0"
#endif
#ifndef EXYNOS_DEVICE_SETTINGS
#define EXYNOS_DEVICE_SETTINGS \
"stdin=serial\0" \
"stdout=serial\0" \
"stderr=serial\0"
#endif
#ifndef EXYNOS_FDTFILE_SETTING
#define EXYNOS_FDTFILE_SETTING
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
EXYNOS_DEVICE_SETTINGS \
EXYNOS_FDTFILE_SETTING \
MEM_LAYOUT_ENV_SETTINGS \
BOOTENV
#endif /* __CONFIG_EXYNOS5_COMMON_H */