u-boot/arch/mips/cpu/start.S
Tom Rini a2ac2b964b Convert CONFIG_SKIP_LOWLEVEL_INIT et al to Kconfig
This converts the following to Kconfig:
   CONFIG_SKIP_LOWLEVEL_INIT
   CONFIG_SKIP_LOWLEVEL_INIT_ONLY

In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31 17:47:49 -04:00

284 lines
5.3 KiB
ArmAsm

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Startup Code for MIPS32 CPU-core
*
* Copyright (c) 2003 Wolfgang Denk <wd@denx.de>
*/
#include <asm-offsets.h>
#include <config.h>
#include <asm/asm.h>
#include <asm/regdef.h>
#include <asm/mipsregs.h>
#ifndef CONFIG_SYS_INIT_SP_ADDR
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \
CONFIG_SYS_INIT_SP_OFFSET)
#endif
#ifdef CONFIG_32BIT
# define STATUS_SET 0
#endif
#ifdef CONFIG_64BIT
# define STATUS_SET ST0_KX
#endif
.set noreorder
.macro init_wr sel
MTC0 zero, CP0_WATCHLO,\sel
mtc0 t1, CP0_WATCHHI,\sel
mfc0 t0, CP0_WATCHHI,\sel
bgez t0, wr_done
nop
.endm
.macro uhi_mips_exception
move k0, t9 # preserve t9 in k0
move k1, a0 # preserve a0 in k1
li t9, 15 # UHI exception operation
li a0, 0 # Use hard register context
sdbbp 1 # Invoke UHI operation
.endm
.macro setup_stack_gd
li t0, -16
PTR_LI t1, CONFIG_SYS_INIT_SP_ADDR
and sp, t1, t0 # force 16 byte alignment
PTR_SUBU \
sp, sp, GD_SIZE # reserve space for gd
and sp, sp, t0 # force 16 byte alignment
move k0, sp # save gd pointer
#if CONFIG_VAL(SYS_MALLOC_F_LEN) && \
!CONFIG_IS_ENABLED(INIT_STACK_WITHOUT_MALLOC_F)
li t2, CONFIG_VAL(SYS_MALLOC_F_LEN)
PTR_SUBU \
sp, sp, t2 # reserve space for early malloc
and sp, sp, t0 # force 16 byte alignment
#endif
move fp, sp
/* Clear gd */
move t0, k0
1:
PTR_S zero, 0(t0)
PTR_ADDIU t0, PTRSIZE
blt t0, t1, 1b
nop
#if CONFIG_VAL(SYS_MALLOC_F_LEN) && \
!CONFIG_IS_ENABLED(INIT_STACK_WITHOUT_MALLOC_F)
PTR_S sp, GD_MALLOC_BASE(k0) # gd->malloc_base offset
#endif
.endm
ENTRY(_start)
/*
* U-Boot entry point.
* Do not add instructions to the branch delay slot! Some SoC's
* like Octeon might patch the final U-Boot binary at this location
* with additional boot headers.
*/
b reset
nop
#if defined(CONFIG_MIPS_INSERT_BOOT_CONFIG)
/*
* Store some board-specific boot configuration. This is used by some
* MIPS systems like Malta.
*/
.org 0x10
.word CONFIG_MIPS_BOOT_CONFIG_WORD0
.word CONFIG_MIPS_BOOT_CONFIG_WORD1
#endif
#if defined(CONFIG_ROM_EXCEPTION_VECTORS)
/*
* Exception vector entry points. When running from ROM, an exception
* cannot be handled. Halt execution and transfer control to debugger,
* if one is attached.
*/
.org 0x200
/* TLB refill, 32 bit task */
uhi_mips_exception
.org 0x280
/* XTLB refill, 64 bit task */
uhi_mips_exception
.org 0x300
/* Cache error exception */
uhi_mips_exception
.org 0x380
/* General exception */
uhi_mips_exception
.org 0x400
/* Catch interrupt exceptions */
uhi_mips_exception
.org 0x480
/* EJTAG debug exception */
1: b 1b
nop
.org 0x500
#endif
reset:
mtc0 zero, CP0_COUNT # clear cp0 count for most accurate boot timing
#if __mips_isa_rev >= 6
mfc0 t0, CP0_CONFIG, 5
and t0, t0, MIPS_CONF5_VP
beqz t0, 1f
nop
b 2f
mfc0 t0, CP0_GLOBALNUMBER
#endif
#ifdef CONFIG_ARCH_BMIPS
1: mfc0 t0, CP0_DIAGNOSTIC, 3
and t0, t0, (1 << 31)
#else
1: mfc0 t0, CP0_EBASE
and t0, t0, MIPS_EBASE_CPUNUM
#endif
/* Hang if this isn't the first CPU in the system */
2: beqz t0, 4f
nop
3: wait
b 3b
nop
/* Init CP0 Status */
4: mfc0 t0, CP0_STATUS
and t0, ST0_IMPL
or t0, ST0_BEV | ST0_ERL | STATUS_SET
mtc0 t0, CP0_STATUS
/*
* Check whether CP0 Config1 is implemented. If not continue
* with legacy Watch register initialization.
*/
mfc0 t0, CP0_CONFIG
bgez t0, wr_legacy
nop
/*
* Check WR bit in CP0 Config1 to determine if Watch registers
* are implemented.
*/
mfc0 t0, CP0_CONFIG, 1
andi t0, (1 << 3)
beqz t0, wr_done
nop
/* Clear Watch Status bits and disable watch exceptions */
li t1, 0x7 # Clear I, R and W conditions
init_wr 0
init_wr 1
init_wr 2
init_wr 3
init_wr 4
init_wr 5
init_wr 6
init_wr 7
b wr_done
nop
wr_legacy:
MTC0 zero, CP0_WATCHLO
mtc0 zero, CP0_WATCHHI
wr_done:
/* Clear WP, IV and SW interrupts */
mtc0 zero, CP0_CAUSE
/* Clear timer interrupt (CP0_COUNT cleared on branch to 'reset') */
mtc0 zero, CP0_COMPARE
#ifdef CONFIG_MIPS_CACHE_DISABLE
/* Disable caches */
PTR_LA t9, mips_cache_disable
jalr t9
nop
#endif
#ifdef CONFIG_MIPS_CM
PTR_LA t9, mips_cm_map
jalr t9
nop
#endif
#ifdef CONFIG_MIPS_INIT_STACK_IN_SRAM
#ifdef CONFIG_MIPS_SRAM_INIT
/* Initialize the SRAM first */
PTR_LA t9, mips_sram_init
jalr t9
nop
#endif
/* Set up initial stack and global data */
setup_stack_gd
# ifdef CONFIG_DEBUG_UART
/* Earliest point to set up debug uart */
PTR_LA t9, debug_uart_init
jalr t9
nop
# endif
#endif
#if !CONFIG_IS_ENABLED(SKIP_LOWLEVEL_INIT)
# ifdef CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD
/* Initialize any external memory */
PTR_LA t9, lowlevel_init
jalr t9
nop
# endif
#endif
#ifdef CONFIG_MIPS_MACH_EARLY_INIT
bal mips_mach_early_init
nop
#endif
#ifdef CONFIG_MIPS_CACHE_SETUP
/* Initialize caches... */
PTR_LA t9, mips_cache_reset
jalr t9
nop
#endif
#if !CONFIG_IS_ENABLED(SKIP_LOWLEVEL_INIT)
# ifndef CONFIG_SYS_MIPS_CACHE_INIT_RAM_LOAD
/* Initialize any external memory */
PTR_LA t9, lowlevel_init
jalr t9
nop
# endif
#endif
#ifndef CONFIG_MIPS_INIT_STACK_IN_SRAM
/* Set up initial stack and global data */
setup_stack_gd
# ifdef CONFIG_DEBUG_UART
/* Earliest point to set up debug uart */
PTR_LA t9, debug_uart_init
jalr t9
nop
# endif
#endif
move a0, zero # a0 <-- boot_flags = 0
PTR_LA t9, board_init_f
jr t9
move ra, zero
END(_start)