u-boot/doc/README.mpc8315erdb
Anton Vorontsov 2e95004deb mpc83xx: Add NAND boot support for MPC8315E-RDB boards
The core support for NAND booting is there already, so this patch
is pretty straightforward.

There is one trick though: top level Makefile expects nand_spl to
be in nand_spl/board/$(BOARDDIR), but we can fully reuse the code
from mpc8313erdb boards, and so to not duplicate the code we just
symlink nand_spl/board/freescale/mpc8315erdb to mpc8313erdb.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>

o silence make during ln echo
o update documentation
o and avoid:

$ ./MAKEALL MPC8315ERDB_NAND
Configuring for MPC8315ERDB board...
sdram.o: In function `fixed_sdram':
/home/r1aaha/git/u-boot/nand_spl/board/freescale/mpc8313erdb/sdram.c:72: undefined reference to `udelay'

by renaming udelay -> __udelay in the spirit of commit
3eb90bad65 "Generic udelay() with watchdog
support".

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2010-01-07 18:33:52 -06:00

105 lines
2.4 KiB
Text

Freescale MPC8315ERDB Board
-----------------------------------------
1. Board Switches and Jumpers
S3 is used to set CONFIG_SYS_RESET_SOURCE.
To boot the image at 0xFE000000 in NOR flash, use these DIP
switch settings for S3 S4:
+------+ +------+
| | | **** |
| **** | | |
+------+ ON +------+ ON
4321 4321
(where the '*' indicates the position of the tab of the switch.)
To boot the image at the beginning of NAND flash, use these
DIP switch settings for S3 S4:
+------+ +------+
| * | | *** |
| *** | | * |
+------+ ON +------+ ON
4321 4321
(where the '*' indicates the position of the tab of the switch.)
When booting from NAND, use u-boot-nand.bin, not u-boot.bin.
2. Memory Map
The memory map looks like this:
0x0000_0000 0x07ff_ffff DDR 128M
0x8000_0000 0x8fff_ffff PCI MEM 256M
0x9000_0000 0x9fff_ffff PCI_MMIO 256M
0xe000_0000 0xe00f_ffff IMMR 1M
0xe030_0000 0xe03f_ffff PCI IO 1M
0xe060_0000 0xe060_7fff NAND FLASH (CS1) 32K
0xfe00_0000 0xfe7f_ffff NOR FLASH (CS0) 8M
When booting from NAND, NAND flash is CS0 and NOR flash
is CS1.
3. Definitions
3.1 Explanation of NEW definitions in:
include/configs/MPC8315ERDB.h
CONFIG_MPC83xx MPC83xx family
CONFIG_MPC831x MPC831x specific
CONFIG_MPC8315 MPC8315 specific
CONFIG_MPC8315ERDB MPC8315ERDB board specific
4. Compilation
Assuming you're using BASH (or similar) as your shell:
export CROSS_COMPILE=your-cross-compiler-prefix-
make distclean
make MPC8315ERDB_config (or MPC8315ERDB_NAND_config for u-boot-nand.bin)
make all
5. Downloading and Flashing Images
5.1 Reflash U-boot Image using U-boot
NOR flash:
tftp 40000 u-boot.bin
protect off all
erase fe000000 fe1fffff
cp.b 40000 fe000000 xxxx
protect on all
You have to supply the correct byte count with 'xxxx'
from the TFTP result log.
NAND flash:
=>tftpboot $loadaddr <filename>
=>nand erase 0 0x80000
=>nand write $loadaddr 0 0x80000
...where 0x80000 is the filesize rounded up to
the next 0x20000 increment.
5.2 Downloading and Booting Linux Kernel
Ensure that all networking-related environment variables are set
properly (including ipaddr, serverip, gatewayip (if needed),
netmask, ethaddr, eth1addr, rootpath (if using NFS root),
fdtfile, and bootfile).
Then, do one of the following, depending on whether you
want an NFS root or a ramdisk root:
=>run nfsboot
or
=>run ramboot
6 Notes
The console baudrate for MPC8315ERDB is 115200bps.