strsep() changes the address that its first argument points to.
We cannot use the changed address as argument of free().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
U-Boot offers a EFI_LOAD_FILE2_PROTOCOL which the Linux EFI stub can use to
load an initial RAM disk. Update the function comments of the
implementation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This adds the driver for the PWM controller found in the Amlogic SoCs.
This PWM is only a set of Gates, Dividers and Counters:
PWM output is achieved by calculating a clock that permits calculating
two periods (low and high). The counter then has to be set to switch after
N cycles for the first half period.
The hardware has no "polarity" setting. This driver reverses the period
cycles (the low length is inverted with the high length) for
PWM_POLARITY_INVERSED.
Disabling the PWM stops the output immediately (without waiting for the
current period to complete first).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The AXG pmx driver gpio request offset needs the pin base to have the
correct pin number.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.
This adds this dynamic switching right before booting Linux
and the configuration steps in the boards documentation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[narmstrong: fixed warning by replacing min() by min_t()]
Use the newly added VIM3 board support instead of the generic W400.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The VIM3 will need a specific code to enable PCIe if enabled in the MCU,
thus add a specific board support for VIM3 & VIM3L.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This imports the G12A & SM1 SoC and boards DT changes from the Linux
commit 9123e3a74ec7 ("Linux 5.9-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the correcly architectured USB Glue node for Meson AXG and the
S400 board in -u-boot.dtsi until support in upstream Linux then
backported.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the board_usb_init()/cleanup() for USB gadget for AXG based
on the code for the G12A architecture.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The registers which are managed by the meson-gxl-usb3 PHY driver are
actually "USB control" registers (which are "glue" registers which
manage OTG detection and routing of the OTG capable port between the
DWC2 peripheral-only controller and the DWC3 host-only controller).
Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-gxl-usb
driver supports the USB control registers on GXL and GXM SoCs (these
were previously managed by the meson-gxl-usb3 PHY driver).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The USB support was initialy done with a set of PHYs and dwc3-of-simple
because the architecture of the USB complex was not understood correctly
at the time (and proper documentation was missing...).
But with the G12A family, the USB complex was correctly understood and
implemented correctly.
This adds a proper driver for the glue, based on the G12A one, but with
enough changes to require a different driver in U-Boot.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This imports the AXG, GXL & GXM SoC and boards DT changes from the Linux
commit b3a9e3b9622a ("Linux 5.8-rc1").
This change also removes GXL & GXM u-boot.dtsi hacks for USB gadget.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl960JkcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDaWCACYjvloDzXQaYaauWwR
whFwgkUAQ8yjadj/12We/X2b7HGisNFNE80e/V4MU8RrJDFZmohZdLWMfRKez29X
d+BG+OzVXxHWozny7ZQ2g1yYJbgCI7sVUeemQjUBZJ6aKPneQlVfwyfT2l88wOVK
yQMqS+ZyVogihR9/NHCOlJHog+6OOoBmc16w1tymM6QcO8ZsYeA66ed8SLnjDb3N
Rg2Ll2RR/lHuD/Fpxt1aUhybXFKSIOr4Qopo5X0hw5B3ibkp6JXGRE2wIwQYw6CA
q+sKTg37CSzylipkQ5EOGdLcXD7r3KIGkSbUMb8wvt6dROarnIuQ+zJeF3sr+l2H
hSoU
=vHqZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for 2021.01 cycle:
This feature set includes a new CPU driver for at91 family, new driver
for PIT64B hardware timer, support for new at91 family SoC named sama7g5
which adds: clock support, including conversion of the clock tree to
CCF; SoC support in mach-at91, pinctrl and mmc drivers update. The
feature set also includes updates for mmc driver and some other minor
fixes and features regarding building without the old Atmel PIT and the
possibility to read a secondary MAC address from a second i2c EEPROM.
- stm32mp: convert drivers to APIs which support live DT
- stm32mp: gpio: minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl93OLYACgkQ4rK92eCq
k3VQ3ggAlv+e3IXylevdLrCGtoPNb0mC3pB7fKcXedZ7YOHi+ag6MfLKFb3K8UCV
1h8iUX3XpGxOuOzOlqu89UFZBZXkbKP3bPnOJD8AliTEcZN/rTdZK43qYbAVM3tL
UvOtCXMzujmGwJsJqLQmXKK761fpcJFzEisajX+d6cz+at3oMF2Yoa/1RcC8Z7fi
DHWaUME132H5A9pzmt84N83neJNgMmFIDyHBWjNSMkvdiE5jz8MAPFrua8FDyymS
w0QmKmN0ub+5kJqXu4X/LCMZUjYozC3lfNbnwRIkXXKJtQuGEea963bBi7Gastdb
gSCQKmrwjtxa4/g/bpalDTMAvirKnQ==
=Q/62
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201003' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm into next
- stm32mp: DT alignment with Linux 5.9-rc4
- stm32mp: convert drivers to APIs which support live DT
- stm32mp: gpio: minor fixes
Currently, the return value of dev_read_u32_default is stored in an u32,
causing the subsequent "if (function < 0)" to always be false:
u32 function;
...
function = dev_read_u32_default(config, "brcm,function", -1);
if (function < 0) {
debug("Failed reading function for pinconfig %s (%d)\n",
config->name, function);
return -EINVAL;
}
Make "function" variable an int to fix this.
Cc: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Factor out reading IP base address to ofdata_to_platdata function, which
is designed for this purpose. Also, drop the dev->priv NULL check, since
this is already done by the dm core when allocating space using
priv_auto_alloc_size feature. (in drivers/core/device.c ->
device_ofdata_to_platdata).
Cc: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add test on the size of ofnode_phandle_args result to avoid access
to uninitialized elements in args[] field.
This patch avoids the issue when gpio-ranges cell size is not 3 as
expected, for example:
gpio-ranges = <&pinctrl 0>;
instead of
gpio-ranges = <&pinctrl 0 112 16>;
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Move the variables definition at the beggining of the function
gpio_stm32_probe().
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
DT alignment with Linux kernel v5.9-rc4 for the STM32MP15x soc
device tree files and the STMicroelectronics boards device tree files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
According to doc/README.distro fdt_addr must not be set when DTB is not
available from hardware. So remove this entry.
Use address 32MB above the start of DRAM for kernel_addr_r. This way
we likely can avoid the self-relocation of the compressed kernel image
before it decompresses to offset 0x8000 from start of DRAM.
Use address 128MB above the start of DRAM for fdt_addr_r, since this is
the maximum location for the end of the kernel. So we avoid overwriting
the DTB.
Use 512k above that for ramdisk_addr_r. This should be enough for the
DTB, rest of DRAM can be used for initrd.
Place boot script / extlinux.conf at offset 0 / 1MB from start of DRAM.
This space is available for processing in U-Boot.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The u-boot,dm-spl DT props are missing on AV96, hence the pinmux and
flash0 nodes are not included in the reduced SPL DT. This prevents
SPI NOR boot from working at all. Fix this by filling them in.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Upon further discussion on the mailing list, we should not get in the
situation where the generic code path to set ethaddr/etc correctly does
not work. Revert this until someone can further debug the smc911x
driver regarding this issue.
This reverts commit 387cbf096e.
Signed-off-by: Tom Rini <trini@konsulko.com>
The R8A774A1 is compatible with the generic rcar-gen3-xhci controller.
This patch adds the compatibility flag, to support the xHCI controller.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Use readx_poll_sleep_timeout() to poll the register status
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use macros with parameter to fill ep_info2, then some macros
for MASK and SHIFT can be removed
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use TRB_TX_TYPE() instead of (TRB_DATA_OUT/IN << TRB_TX_TYPE_SHIFT)
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For normal TRB fields:
use TRB_LEN(x) instead of ((x) & TRB_LEN_MASK);
and use TRB_INTR_TARGET(x) instead of
(((x) & TRB_INTR_TARGET_MASK) << TRB_INTR_TARGET_SHIFT)
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There some vendor quirks for MTK xHCI 0.96 host controller:
1. It defines some extra SW scheduling parameters for HW
to minimize the scheduling effort for synchronous and
interrupt endpoints. The parameters are put into reserved
DWs of slot context and endpoint context.
2. Its TDS in Normal TRB defines a number of packets that
remains to be transferred for a TD after processing all
Max packets in all previous TRBs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
