Certain SoCs with K3 architecture have integrated a C66 Corepac DSP
subsystem and an advanced C71 DSPs. Introduce a remoteproc driver
that that does take care of loading an elf to any of the specified
DSPs and start it.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Some Texas Instruments K3 family of SoCs have one of more Digital Signal
Processor (DSP) subsystems that are comprised of either a TMS320C66x
CorePac and/or a next-generation TMS320C71x CorePac processor subsystem.
Add the device tree bindings document for the C66x DSP devices on these
SoCs. The added example illustrates the DT nodes for the first C66x DSP
device present on the K3 J721E family of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
SoCs with K3 architecture have an integrated Arm Cortex-R5F subsystem
that is comprised of dual-core Arm Cortex-R5F processor cores. This R5
subsytem can be configured at boot time to be either run in a LockStep
mode or in an Asymmetric Multi Processing (AMP) fashion in Split-mode.
This subsystem has each Tightly-Coupled Memory (TCM) internal memories
for each core split between two banks - TCMA and TCMB.
Add a remoteproc driver to support this subsystem to be able to load
and boot the R5 cores primarily in LockStep mode or split mode.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
The Texas Instruments K3 family of SoCs have one of more dual-core
Arm Cortex R5F processor subsystems/clusters (R5FSS). Add the device
tree bindings document for these R5F subsystem devices. These R5F
processors do not have an MMU, and so require fixed memory carveout
regions matching the firmware image addresses. The nodes require more
than one memory region, with the first memory region used for DMA
allocations at runtime. The remaining memory regions are reserved
and are used for the loading and running of the R5F remote processors.
The added example illustrates the DT nodes for the single R5FSS device
present on K3 AM65x family of SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Power domain for the remote cores needs to be handled in a right
sequence as mandated by the spec. Introduce tisci helper apis
that can control power-domains of remote cores. TISCI clients
can use this api and control the remote cores power domain instead
of hooking it to power-domain layer.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Introduce rproc_elf_get_boot_addr() that returns the entry point of
the elf file. This api auto detects the 64/32 bit elf file and returns
the boot addr accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Introduce a common remoteproc elf loader and checker functions that
automatically detects the 64 bit elf file or 32 bit elf file and
loads/checks the sections accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
The current rproc-elf-loader supports loading of only 32 bit elf files.
Introduce support for loading of 64 bit elf files in rproc-elf-loader.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
rproc_elf32_load_image() rely on user to send a valid address for elf loading.
Instead do a sanity check on the address passed by user. This will help
all rproc elf users to not call sanity_check explicitly before calling
elf_loading.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Introduce a new parameter "size" that accepts size of the region to
remoteproc ops callback device_to_virt(). This can enforce more checks
on the region that device_to_virt() is dealing with.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
am65x ROM support booting over UART. And U-Boot built for am65x EVM
supports UART boot as well. Add the UART boot procedure into the README
also providing a corresponding example command sequence for execution
on a host PC.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Activate early console functionality on AM654x devices to allow for an
alternate serial port to be used to support UART-based boot. This is so
that System Firmware (SYSFW) can get loaded over the serial port prior
to the main console being brought up and made available.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Although we currently use the MAIN_UART0 for R5 SPL console output there
are cases where we require access to the MCU_UART0 as well for example in
case of UART-based Y-Modem boot. To support these scenarios add related
DTS definitions to be able to use that UART early on.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
In order to allow booting TI K3 family SoCs via Y-Modem add support for
loading System Firmware by tapping into the associated SPL core loader
function.
In this context also make sure a console is available and if not go
ahead and activate the early console feature which allows bringing up
an alternate full console before the main console is activated. Such
an alternate console is typically setup in a way that the associated
UART can be fully initialized prior to SYSFW services being available.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Implement an early console functionality in SPL that can be used before
the main console is being brought up. This helps in situations where the
main console is dependent on System Firmware (SYSFW) being up and running,
which is usually not the case during the very early stages of boot. Using
this early console functionality will allow for an alternate serial port
to be used to support things like UART-based boot and early diagnostic
messages until the main console is ready to get activated.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Expose SPL's Y-Modem core loader function via the common SPL header
file so it can be re-used for purposes other than loading U-Boot itself.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
During FIT reading through ymodem_read_fit() the function
xyzModem_stream_read() is being used which returns zero once the end
of a stream has been reached. This could lead to an premature exit from
ymodem_read_fit() with certain-sized FIT images reporting that zero
bytes overall were read. Such a premature exit would then result in an
-EIO failure being triggered within the spl_load_simple_fit() caller
function and ultimately lead to a boot failure.
Fix this logic by simply aborting the stream read loops and continuing
with the regular code flow which ultimately would lead to returning
the number of bytes to be read ('size') as expected by the callers of
ymodem_read_fit().
Fixes: fa715193c0 ("spl: Add an option to load a FIT containing U-Boot from UART")
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
The doc currently uses sandbox_defconfig as examples of enabling
debug/verbose output of binman. However during a sandbox build it
does not call binman at all. Change it to qemu-x86_defconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this produces a 16-byte file. It is intended to start 16 bytes
before the end of ROM and pads with zeroes to readh the end.
But binman sometimes wants to add an image-header at the very end of ROM.
Furthermore binman automatically pads the data if it is finishes early.
Drop the padding in resetvec and let binman handle it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This is not used anywhere now, so drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Since x86 users binman now, we don't need this compile-time define.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Many of the Kconfig options do not apply to FSP2. Update them to use the
FSP_VERSION1 condition instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Move the code to determine the size of a cache record into a function so
we can use it elsewhere in this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The write functions do actually change the contents of memory so it is not
correct to use 'const'. Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a field to the PCI emulator per-device data which records which device
is being emulated. This is useful when the emulator needs to check the
device for something.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: rebase the patch against u-boot-x86/master to get it applied cleanly]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present when these fail to boot there is no message, just a hang. Add a
panic so it is obvious that something when wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For the correct power cycle sequence with stm32_sdmmc2, the write of the
power cycle value in PWRCTL field of SDMMC_POWER register is now done in
stm32_sdmmc2_host_power_cycle() and no more in stm32_sdmmc2_pwrcycle().
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Some MMC peripherals require specific power cycle sequence, where some
registers need to be written between the regulator is turned off and then
back on. This is the case for the MMC IP embedded in STM32MP1 SoC.
In STM32MP157 reference manual [1], the power cycle sequence is:
1. Reset the SDMMC with the RCC.SDMMCxRST register bit. This will reset
the SDMMC to the reset state and the CPSM and DPSM to the Idle state.
2. Disable the Vcc power to the card.
3. Set the SDMMC in power-cycle state. This will make that the
SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are driven low, to prevent the card
from being supplied through the signal lines.
4. After minimum 1ms enable the Vcc power to the card.
5. After the power ramp period set the SDMMC to the power-off state for
minimum 1ms. The SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are set to
drive “1”.
6. After the 1ms delay set the SDMMC to power-on state in which the
SDMMC_CK clock will be enabled.
7. After 74 SDMMC_CK cycles the first command can be sent to the card.
The step 3. cannot be handled by the current framework implementation.
A new callback (host_power_cycle) is created, and called in
mmc_power_cycle(), after mmc_power_off().
The incorrect power cycle sequence has shown some boot failures on
STM32MP1 with some SD-cards, especially on cold boots when the input
frequency is low (<= 25MHz).
Those failures are no more seen with this correct power cycle sequence.
[1] https://www.st.com/resource/en/reference_manual/DM00327659.pdf
Signed-off-by: Yann Gautier <yann.gautier@st.com>
In SPL, all the available mmc devices gets initialized during boot.
This might not work in cases where clocks are not available for
certain mmc devices(other than boot device) and the support for
enabling device might not be ready.
Texas Instruments' K3 J721E device having a central system controller
(dmsc) is one such example falling in this category. Below is the
sequence for the failing scenario:
- ROM comes up in SD mode and loads SPL by just initialing SD card.
- SPL loads dmsc firmware from SD Card.
Since ROM has enabled SD, SPL need not enable the SD, just need
to re initialize the card. But SPL is trying to initialize other MMC
instances which are in disabled state. Since dmsc firmware is not yet
available, devices cannot be enabled. So in SPL, initialize only the
mmc device that is needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The EEPROM contains eth1 MAC address as well, use it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Update board environment to match the one used in deployment.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Update headers generated by quartus to the latest version.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Pick minor changes from the downstream DT, disable MMC, add GMAC0 node
and adjust PHY skew settings for GMAC1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Build the keystone 3 platforms with the keystone 2 platforms, in order
to get back more room in the "catch-all" build jobs.
Signed-off-by: Tom Rini <trini@konsulko.com>
As both "catch-all" ARM jobs are nearing their time limit, move all of
the bcm SoC boards into a single job.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdnCy/AAoJEB6zHgIOrC/Izp4IAJVDE0oyOYcwBoCsAqa8zvMJ
/G815T1TGyc6674TQ+Px47t+1O9InClag576E1ttKVSZHnTqH9AW1aGdVqYFgmwu
bbk7a/N2bSYc1ZruiH1YMzwVMTmwaIvn9cvNeBMkQ0cXBP6R7m9DsupaTG9mNsll
7wNFF6gZCOXQEOL6hgxerxr6UM2xaQMpSqfYhfYfmHyU0S86Cr1J7dORL1MHhZ4/
WLVuxCPpgeTwiZ0i9TerC0eH0agPQ2dmtDPAQFn+RihVS29YNDTaR+a4XVKJJ6hs
Y/77d0JYmPSY5JgYLAdjqx+GQKKqy9kpdHJz+sXCiolDdYHmG3c+4zQzrLzkH+k=
=Y0qG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2020.01-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features and fixes for 2020.01 cycle
The feature set includes support for two new boards from Microchip AT91:
The sama5d27_wlsom1_ek , an evaluation kit which includes the SAMA5D2
SOC packaged in a 256 MB LPDDR2 SIP, on a SOM including wireless, which
is placed on evaluation kit with sd-card, ethernet, LCD, Camera sensor,
QSPI, etc
The sam9x60ek, an evaluation kit for the new SoC based on ARM926j , the
SAM9X60 . The evaluation kit includes NAND flash, QSPI, Ethernet, Audio,
Camera sensor connector, etc.
The full support for sam9x60ek will come at a later time. There are
still missing bits regarding the clock support and power management
controller.
The major corrections in this pull request are:
Fixes for the SetVariable() boot service.
Device path node for NVMe drives.
Disable CONFIG_CMD_NVEDIT by default.
-----BEGIN PGP SIGNATURE-----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=nzgb
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc1
The major corrections in this pull request are:
Fixes for the SetVariable() boot service.
Device path node for NVMe drives.
Disable CONFIG_CMD_NVEDIT by default.
- Python3 conversion of genboardscfg.py
- Resync Kconfiglib.py
- Switch to running CI on Ubuntu "bionic" to facilitate Python 3.6 being
the minimum we use and test.
In order to run all filesystem tests we need to have newer ext4 tools,
move up to Ubuntu 18.04 'bionic' for our base. We need to change
slightly how we invoke the provided grub-mkimage. This will also make
future python3 work easier.
Signed-off-by: Tom Rini <trini@konsulko.com>
When running as another user we might not be able to use '..' for
certain directories and this is the default for buildman. Specify an
output directory instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
We may not always be able to write to the default output directory so
have a temporary directory for our output be created.
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Suggested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the reverting of a previous change to spl_boot_device,
this board needs a new solution to determining if we're booting
from MMC1 or MMC2.
This patch creates board_boot_order function which overrides the
standard, and returns not only MMC1, or MMC2, but also can fall
back to NAND or the serial downloader should other boot options
fail.
Signed-off-by: Adam Ford <aford173@gmail.com>
