This converts the following to Kconfig:
CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
Signed-off-by: Tom Rini <trini@konsulko.com>
All of these symbols are not referenced anywhere else in the code, so
remove them.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_OHCI_SWAP_REG_ACCESS
CONFIG_SYS_USB_OHCI_CPU_INIT
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
CONFIG_SYS_USB_OHCI_SLOT_NAME
CONFIG_USB_ATMEL
CONFIG_USB_ATMEL_CLK_SEL_PLLB
CONFIG_USB_ATMEL_CLK_SEL_UPLL
CONFIG_USB_OHCI_LPC32XX
CONFIG_USB_OHCI_NEW
Signed-off-by: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The generic arm linker script contains this section:
.bss __rel_dyn_start (OVERLAY) : {
...
}
The (OVERLAY) syntax in the description causes the .bss section to be
included in the NOR area of the image:
$ objdump -t -j .bss spl/u-boot-spl
SYMBOL TABLE:
0000c61c l d .bss 00000000 .bss
0000c640 l O .bss 00000040 __value.0
0000c68c g O .bss 00000000 __bss_end
0000c61c g O .bss 00000000 __bss_start
0000c680 g O .bss 0000000c stdio_devices
This is what the custom linker script tries to avoid, as the NOR area is
read-only.
Remove the OVERLAY syntax to fix the BSS location:
$ objdump -t -j .bss spl/u-boot-spl
SYMBOL TABLE:
83000000 l d .bss 00000000 .bss
83000000 l O .bss 00000040 __value.0
0000c61c g O .bss 00000000 __image_copy_end
8300004c g O .bss 00000000 __bss_end
83000000 g O .bss 00000000 __bss_start
83000040 g O .bss 0000000c stdio_devices
This restores the state of the linker script before the patch that fixed
the linker lists issue.
Fixes: f6810b749f ("aspeed/ast2600: Fix SPL linker script")
Signed-off-by: Joel Stanley <joel@jms.id.au>
The EVB has an EEPROM on bus 3 and a LM75 temp sensor on bus 7. Enable
those busses we can test the I2C driver.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The same as the upstream Linux device tree, each i2c bus has a property
specifying the reset line.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Set the pinctrl groups for each I2C bus. These are essential to
I2C operating correctly.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Mark the memory node with u-boot,dm-spl so we can use it
from early SPL on both R5 and A53.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The spl_enable_dcache() function calls dram_init_banksize()
to get the total memory size. Normally the dram_init_banksize()
setups the memory banks, while the total size is reported
by ddr_init(). This worked so far for K3 since we set the
gd->ram_size in dram_init_banksize() as well.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
implement overrides for spl_spi_boot_bus() and spl_spi_boot_cs()
lookup functions according to bootmode selection, so as to support
both QSPI and OSPI boot using the same build.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
This converts the following to Kconfig:
CONFIG_KIRKWOOD_EGIGA_INIT
CONFIG_KIRKWOOD_PCIE_INIT
CONFIG_KIRKWOOD_RGMII_PAD_1V8
CONFIG_KM_DISABLE_PCIE
Signed-off-by: Tom Rini <trini@konsulko.com>
The way that secure boot is implemented today on NXP ARM platforms does
not reuse the elements found in include/config_fsl_chain_trust.h to
construct CONFIG_SECBOOT but instead board header files have their
environment setup as needed and then fsl_setenv_chain_of_trust() will
set secureboot in the environment. Remove a large number of unused
defines here.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move setting of SPL_UBOOT_KEY_HASH to a non-NULL value to Kconfig. As
part of this, change fsl_secboot_validate(...) to check that it is
passed a non-empty string, rather than non-NULL.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Make all of the CHAIN_OF_TRUST options be under a single menu and add a
comment for the rest, so the resulting config file reads more clearly.
Remove duplicate CHAIN_OF_TRUST options from
board/congatec/common/Kconfig. Remove duplicate NXP_ESBC config
questions and move to arch/Kconfig.nxp.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_KEY_REVOCATION
CONFIG_SYS_FSL_SFP_BE
CONFIG_SYS_FSL_SFP_LE
CONFIG_SYS_FSL_SFP_VER_3_0
CONFIG_SYS_FSL_SFP_VER_3_2
CONFIG_SYS_FSL_SFP_VER_3_4
CONFIG_SYS_FSL_SRK_LE
This partly means making sure to enable SYS_FSL_ERRATUM_A007186 only for
when CHAIN_OF_TRUST is enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_SEC_MON
CONFIG_SYS_FSL_SEC_MON_BE
CONFIG_SYS_FSL_SEC_MON_LE
Signed-off-by: Tom Rini <trini@konsulko.com>
We rename the S5P specific "CONFIG_PWM" to CONFIG_PWM_S5P and move it to
Kconfig. Given the usage of CONFIG_PWM_NX, we have that select this new
symbol.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmK9nEUcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyEu0B/4v1EQOMBL+VXns8Ipo
Xeq+RDUX/24XcB5s6sTcNlWzvYuX6Z7DCGJ0loK5JxelrOy+YNkRbTRMom1eW9Kn
9dmKa0bcO7auJEww3Nln1IFyx+FXQFGR1V3g1U4535l8b7urTioIK0MUSrG/GLpe
Rlbh31GAYtrGvl06W1F7mwhg7/0AT8IhUFaY9G7s7gKA5muGQQ7ED4nKVoZPeTAl
lrQ/Ecym1ND7aOhd/vuEBtgoGxDWzwf8piT8qykJluJKzBV1Hic0RXCNBmtrTORz
b1GOOpRUgcnTv9U8j4PRyYGKDnmS2OmV2AwL8+V9UJfJgQrkcRlbgpCysIPmMBzo
YPRt
=D79P
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.10 cycle:
This feature set includes mostly fixes and alignments: DT alignment with
Linux for sama7g5, removal of invalid eeprom compatibles, removal of
extra debug_uart_init calls for all at91 boards, support for pio4 driver
pioE bank, and other minor fixes and enhancements for sam9x60 and
sama5d2_icp boards.
On versal platform, enable apb linear mode for apb read and write
execute operations amd disable it when using dma reads. This is done by
xilinx_pm_request() secure calls when CONFIG_ZYNQMP_FIRMWARE is enabled,
else we use direct raw reads and writes in case of mini U-Boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-5-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When flash operated at non default mode like DDR, flash need to be reset
to operate in SDR mode to read flash ids by spi-nor framework. Reset the
flash to the default state before using the flash. This reset is handled
by a gpio driver, in case of mini U-Boot as gpio driver is disabled, we
do raw read and write access by the registers.
Versal platform utilizes spi calibration for read delay programming, so
incase by default read delay property is set in DT. We make sure not to
use read delay from DT by overwriting read_delay with -1.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Introduce board/siemens/common/Kconfig and have it hold FACTORYSET to
start with. Use select for this on the boards that need it.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
of U-Boot usage.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since bb5930d5c9 ("exynos: video: Convert several boards to driver
model for video") there have been no callers of any of the exynos_lcd_*
family of functions. Remove these from the boards, and then remove
unused logo and related code as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
We want to keep all of the default values for SPL_LDSCRIPT in the same
place both for overall clarity as well as not polluting unrelated config
files.
Signed-off-by: Tom Rini <trini@konsulko.com>
The commit 99e2fbcb69 ("linker_lists: Rename sections to remove .
prefix") changed the name of the linker list sections. As the Aspeed SPL
linker wasn't in the tree yet, it missed the change.
This updates the SPL linker to match arch/arm/cpu/u-boot-spl.lds which
Aspeed was copied from.
Fixes: 442a69c143 ("configs: ast2600: Move SPL bss section to DRAM space")
Signed-off-by: Joel Stanley <joel@jms.id.au>
The memory on this board is microchip 24aa025e48 which is compatible with
at24c02 with a page size of 16.
Fix the compatible accordingly.
Reported-by: Sergiu Moga <sergiu.moga@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
microchip,24aa025e48 does not exist in the bindings of this driver.
It can be replaced with atmel,at24c02 which is a standard compatible
and the memory is compatible with this one, depending on the page size.
microchip 24aa02e48 has a page size of 8, while 24aa025e48 has a page
size of 16 bytes.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
Change the compatible of the qspi child node to
`jedec,spi-nor` so that it can be properly found
when probing the bus.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
This patch adds support for the SHA-256 Secure Hash Algorithm for CPUs
that have support for the SHA-256 part of the ARM v8 Crypto Extensions.
It greatly improves sha-256 based operations, about 17x faster on iMX8M
evk board. ~12ms vs ~208ms for a 20MiB kernel sha-256 verification.
asm implementation is a simplified version of the Linux version (from
Ard Biesheuvel).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
This patch adds support for the SHA-1 Secure Hash Algorithm for CPUs
that have support for the SHA-1 part of the ARM v8 Crypto Extensions.
It greatly improves sha-1 based operations, about 10x faster on iMX8M
evk board. ~12ms vs ~165ms for a 20MiB kernel sha-1 verification.
asm implementation is a simplified version of the Linux version (from
Ard Biesheuvel).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
"size-cells" of the nand controller node should be 0 as the "reg"
property of the nand device node contains the chip select number and not
address information.
The patch fixes the below compilation warning
arch/arm/dts/zynq-zc770-xm011.dtb: Warning (reg_format):
/axi/memory-controller@e000e000/nand-controller@0,0/nand@0:reg: property
has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6e90665a2dad7fe8ade10b8f57101f8144963791.1655288559.git.michal.simek@amd.com
