Linux kernel binding is using atmel,24c01 compatible string. On the
other hand there is atmel,24c01a which is not listed in the kernel.
Add compatible string without "a" suffix to be compatible with Linux
kernel binding.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Simplify the code a bit by using dev_read_addr_ptr() instead of
dev_read_addr(). This avoids having to cast explicitly to the
struct nomadik_mtu_regs.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Nomadik GPIO is a fairly simple GPIO module used in the ST-Ericsson
Ux500 SoCs (and some older Nomadik SoCs). It uses registers where
each GPIO is represented as a single bit, plus "set" and "clear"
registers that allow updating the state without having to read the
existing state.
The driver implements support for it for use together with DM_GPIO
and the existing ste-dbx5x0.dtsi device tree.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The original U-Boot port for the ST-Ericsson U8500 SoC was dropped
in commit 68282f55b8 ("arm: Remove unused ST-Ericsson u8500 arch").
Most of the drivers related to the old port were removed, but the
db8500_gpio.c driver was forgotten for some reason. There is no way
to select it and it does not compile anymore because of missing
headers, so let's just remove it.
The new port for U8500 introduced in commit 689088f9da
("arm: Add support for ST-Ericsson U8500 SoC") fully embraces the
new Driver Model and device trees where possible, so this is
preparation to add a new, simplified GPIO driver based on DM_GPIO.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fix find_boot_device() to set bootdev_root if it finds the
bootdev from BootNext. Currently it sets the bootdev_root only
when it finds bootdev from BootOrder.
Fixes: c74cd8bd08 ("efi_loader: capsule: add capsule_on_disk support")
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Accked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If multiple capsules are applied, the FMP drivers for the individual
capsules can expect the value of CapsuleLast to be accurate. Hence
CapsuleLast must be updated after each capsule.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
* Use log category LOGC_EFI. This allows to remove 'EFI:' prefixes in
messages.
* Rephrase some of the messages.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When reading a directory using EFI_FILE_PROTOCOL.Read() provide file
attributes and timestamps.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When reading a directory in the UEFI file system we have to return file
attributes and timestamps. Copy this data to the directory entry structure.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Aside from the usual fixes and updates one visible change is the
MMC update, which fixes some lingering bugs and gives a decent speed
increase on some boards (9->19 MB/s on H6, 21->43 MB/s on A64 eMMC).
I am keeping an watchful eye on bug reports here, to spot any correctness
regressions.
Another change is finally the enablement of the first USB host port on
many boards without micro-USB (data) sockets, like the Pine64 family.
That doubles the number of usable USB ports from 1 to 2 on those boards.
Some smaller fixes, 4GB DRAM support (on the H616) and a new board (ZeroPi)
conclude this first round of changes.
Compile-tested for all 157 sunxi boards, boot-tested on Pine H64,
Pine64-LTS, OrangePi Zero 2 and BananaPi M2 Berry.
Summary:
- DT update for H3/H5/H6
- Enable first USB port on boards without micro-USB
- ZeroPi board support
- 4GB DRAM support for H616 boards
- MMC fixes and speed improvement
- some fixes
At the moment the Allwinner MMC driver parses the bus-width and
non-removable DT properties itself, in the probe() routine.
There is actually a generic function provided by the MMC framework doing
this job, also it parses more generic properties like broken-cd and
advanced transfer modes.
Drop our own code and call mmc_of_parse() instead, to get all new
features for free.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
To avoid the complexity of DMA operations (with chained descriptors), we
use repeated MMIO reads and writes to the SD_FIFO_REG, which allows us
to drain or fill the MMC data buffer FIFO very easily.
However those MMIO accesses are somewhat costly, so this limits our MMC
performance, to between 17 and 22 MB/s, but down to 9.5 MB/s on the H6
(partly due to the lower AHB1 frequency).
As it turns out we read the FIFO status register after *every* word we
read or write, which effectively doubles the number of MMIO accesses,
thus effectively more than halving our performance.
To avoid this overhead, we can make use of the FIFO level bits, which are
in the very same FIFO status registers.
So for a read request, we now can collect as many words as the FIFO
level originally indicated, and only then need to update the status
register.
We don't know for sure the size of the FIFO (and it seems to differ
across SoCs anyway), so writing is more fragile, which is why we still
use the old method for that. If we find a minimum FIFO size available on
all SoCs, we could use that, in a later optimisation.
This patch increases the eMMC read speed on a Pine64-LTS from about
22MB/s to 44 MB/s. SD card reads don't gain that much, but with 23 MB/s
we now reach the practical limit for 3.3V SD cards.
On the H6 we double our transfer speed, from 9.5 MB/s to 19.7 MB/s.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Newer SoCs have a self calibration feature, which avoids us writing hard
coded phase delay values into the controller.
Consolidate the code by avoiding unnecessary #ifdefs, and also enabling
the feature for all those newer SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
All SoCs since the Allwinner A64 (H5, H6, R40, H616) feature the so
called "new timing mode", so enable this in Kconfig for those SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Among the SoCs using the "new timing mode", only the A83T needs to
explicitly switch to that mode.
By just defining the symbol for that one odd A83T bit to 0 for any other
SoCs, we can always OR that in, and save the confusing nested #ifdefs.
Clean up the also confusing new_mode setting on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Most Allwinner SoCs which use the so called "new timing mode" in their
MMC controllers actually use the double-rate PLL6/PERIPH0 clock as their
parent input clock. This is interestingly enough compensated by a hidden
"by 2" post-divider in the mod clock, so the divider and actual output
rate stay the same.
Even though for the H6 and H616 (but only for them!) we use the doubled
input clock for the divider computation, we never accounted for the
implicit post-divider, so the clock was only half the speed on those SoCs.
This didn't really matter so far, as our slow MMIO routine limits the
transfer speed anyway, but we will fix this soon.
Clean up the code around that selection, to always use the normal PLL6
(PERIPH0(1x)) clock as an input. As the rate and divider are the same,
that makes no difference.
Explain the hardware differences in a comment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When enabling PHYS_64BIT on 32-bit platforms, we get two warnings about
pointer casts in sunxi_mmc.c. Those are related to MMIO addresses, which
are always below 1GB on all Allwinner SoCs, so there is no problem with
anything having more than 32 bits.
Add the proper casts to make it compile cleanly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The delay and bus-width setup are slightly different across the
Allwinner SoC generations, and we covered this so far with some
preprocessor conditionals.
Use the more readable IS_ENABLE() instead.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The H616 is our first supported Allwinner SoC which goes beyond the 4GB
address space "barrier", by having more than 32 address bits.
Lift the preliminary 3GB DRAM limit for the H616, and update the page
table setup on the way, to actually map that last GB as well.
As not all devices are actually capable of dealing with more than 32
bits (the DMA in the EMAC for instance), we also limit U-Boot's own
DRAM usage to 4GB on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
We hardcode the pinctrl setting for the MMC controllers in boards.c,
since we need them also in the SPL, where there is no DT yet.
Add the respective setting for the H616 SoC, to enable eMMC on boards
with this SoC as well.
Also to make diagnosing this problem easier, print a warning if a board
tries to setup MMC2 pins without a respective SoC setting being defined.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan at amarulasolutions.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec at siol.net>
ZeroPi is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner H3 SOC.
ZeroPi features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 256MB/512MB DDR3 RAM
- microsd slot
- 10/100/1000Mbps Ethernet
- Debug Serial Port
- DC 5V/2A power-supply
Signed-off-by: Yu-Tung Chang <mtwget@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
OrangePi PC2 board has DRAM with ODT, so enable it.
H5 SoC is also connected to voltage regulator. It's default value is
reasonable at reset, but might be too low when rebooting with a lower
voltage programmed. In order to avoid instability, enable driver for it
and set it to appropriate voltage.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
[Andre: remove original ZQ value change, adjust commit message]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Most clock factors and dividers in the H6 PLLs use a "+1 encoding",
which we were missing on two occasions.
This fixes the MMC clock setup on the H6, which could be slightly off due
to the wrong parent frequency:
mmc 2 set mod-clk req 52000000 parent 1176000000 n 2 m 12 rate 49000000
Also the CPU frequency (PLL1) was a tad too high before.
For PLL5 (DRAM) we already accounted for this +1, but in the DRAM code
itself, not in the bit field macro. Move this there to be aligned with
what the other SoCs and other PLLs do.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Recent Allwinner platforms (starting with the H3) only use the MUSB
controller for peripheral mode and use HCI for host mode. As a result,
extra steps need to be taken to properly route USB signals to one or
the other. More precisely, the following is required:
* Routing the pins to either HCI/MUSB (controlled by PHY);
* Enabling USB PHY passby in HCI mode (controlled by PMU).
The current code will enable passby for each PHY and reroute PHY0 to
MUSB, which is inconsistent and results in broken USB peripheral support.
Passby on PHY0 must only be enabled when we want to use HCI. Since
host/device mode detection is not available from the PHY code and
because U-Boot does not support changing the mode dynamically anyway,
we can just mux the controller to MUSB if it is enabled and mux it to
HCI otherwise.
This fixes USB peripheral support for platforms with PHY0 dual-route,
especially H3/H5 and V3s.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Update the H3 DT files from the Linux 5.12 release.
The changes update some boards, and don't affect U-Boot, but fix Gigabit
Ethernet when this DT is passed on to the Linux kernel.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Update the H5 DT files from the Linux 5.12 release.
The changes don't affect U-Boot at all, but fix Gigabit Ethernet when
this DT is passed on to the Linux kernel. It also introduces DVFS.
This also updates the shared sunxi-h3-h5.dtsi, but that only adds nodes
that are of no concern to U-Boot.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Update the H6 DT files from the Linux 5.12 release.
The changes are minimal (many LED node renames), but also help to enable
USB port 0 in U-Boot (later), enable the RSB device (not yet used in
U-Boot), and also introduce an MMC frequency limit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
As seen with clang-12:
warning: __asm_invalidate_l3_dcache changed binding to STB_WEAK
As we indeed use ENTRY and then declare the function weak manually. Use
the WEAK declarative from <linux/linkage.h> instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
On arm64, board info is not applicable and kernel command line patched into
the DT, so the LMB reservation here makes no sense anymore. On legacy arm32,
this might still be necessary on systems which do not use DT or use legacy
ATAGS. Disable this LMB reservation on arm64.
This also permits Linux DT to specify reserved memory node at address close
to the end of DRAM bank, i.e. overlaping with U-Boot location. Since after
boot, U-Boot will be no more, this is OK.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hai Pham <hai.pham.ud@renesas.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Rini <trini@konsulko.com>
Fix following compilation issue when SYS_DCACHE_OFF is enable:
drivers/misc/scmi_agent.c:128: undefined reference to `mmu_set_region_dcache_behaviour'
when SYS_DCACHE_OFF is enable, mmu_set_region_dcache_behaviour() must be
defined.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
On implementations that support VHE, the layout of the CPTR_EL2
register depends on whether HCR_EL2.E2H is set. If the bit is
set, CPTR_EL2 uses the same layout as CPACR_EL1 and can in fact
be accessed through that register. In that case, jump to the
EL1 code to enable access to the FP/SIMD registers. This allows
U-Boot to run on systems that pass control to U-Boot in EL2 with
EL2 Host mode enabled such as machines using Apple's M1 SoC.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Acked-by: Marc Zyngier <maz@kernel.org>
The cavium,bdk node is a non-standard dt node used by the BDK and
therefore it is removed from the dt before booting Linux. Do not
require this node to exist as it won't for standard dt's.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Extend CONFIG_SYS_BAUDRATE_TABLE and include all standard baudrates and
also nonstandard up to the 6 MBaud. U-Boot's A3720 UART driver can use
baudrates from 300 Baud to 6 MBaud.
This changes all A3720 boards, since all of them include either
mvebu_armada-37xx.h or turris_mox.h config file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Unfortunately the UART driver in current Linux for Armada 3700 expects
UART's parent clock to be XTAL and calculats baudrate divisor according
to XTAL clock. Therefore we must switch back to XTAL clock before
booting kernel.
Implement .remove method for this driver with DM_FLAG_OS_PREPARE flag
set.
If current baudrate is unsuitable for XTAL clock then we do not change
anything. This can only happen if the user either configured unsupported
settings or knows what they are doing and has kernel patches which allow
usage of non-XTAL parent clock.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Using TBG clock as parent clock for UART allows us using higher
baudrates than 230400.
Turris MOX with external FT232RL USB-UART works fine up to 3 MBaud
(which is maximum for this USB-UART controller), while EspressoBIN with
integrated pl2303 USB-UART also works fine up to 6 MBaud.
Slower baudrates with TBG as a parent clock can be achieved by
increasing TBG dividers and oversampling divider. When using the slowest
TBG clock, minimal working baudrate is 300.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Setting DM_FLAG_PRE_RELOC for Armada 3720 clock drivers (TBG and
peripheral clocks) makes it possible for serial driver to retrieve clock
rates via clk API.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
UART parent clock is by default the platform's xtal clock, which is
25 MHz.
The value defined in the driver, though, is 25.8048 MHz. This is a hack
for the suboptimal divisor calculation
Divisor = UART clock / (16 * baudrate)
which does not use rounding division, resulting in a suboptimal value
for divisor if the correct parent clock rate was used.
Change the code for divisor calculation to round to closest value, i.e.
Divisor = Round(UART clock / (16 * baudrate))
and change the parent clock rate value to that returned by
get_ref_clk().
This makes A3720 UART stable at standard UART baudrates between 1800 and
230400.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
With the spear family of platforms gone, remove references to them from
the build jobs.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
While this platform has not yet been converted, there is active efforts
to do so. Keep the platform for now.
This reverts commit aa697e6904.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Remove a large number of platforms that did not migrate to DM_PCI or
DM_USB by 2 years past the migration deadline and do not have a
migration imminent.
If MUSB support is disabled, these parts of the code will fail to build.
Cc: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tom Rini <trini@konsulko.com>
